SwitchBot W1201500 Door Alarm Contact Sensor User Manual

SwitchBot W1201500 Door Alarm Contact Sensor

PRODUCT INFORMATION

MODEL NO.: W1201500

In the Box

• Contact Sensor
• Magnet
• AAA Batteries x 2
• User Manual
• Screw Pack
• Sticker (adhered to Contact Sensor)
• Sticker (adhered to Magnet)

Device Instruction

Preparation

• A smartphone or tablet with Bluetooth 4.2 or above
• Download the Switch Bot app
• Create a SwitchBot account and sign in
• (Optional) If you intend to use the Cloud Service feature, you need to set up a SwitchBot Hub Mini (sold separately) and connect your phone to the internet

Getting Started

• Remove the Battery Case. Install two AAA batteries into the battery box following the “+” and “-“signs. Then put the Battery Case back.
• Open the Switch Bot app and sign in.
• On the app, tap the “+” icon on the top right of the homepage. Tap the “Contact Sensor” icon and follow the instructions to complete the setup.

Safety Information

• Keep the device away from humid or hot environments.
• Remove the batteries when not used for a long period of time.
• Do not attempt to disassemble, repair, or modify the device.
• Do not use any other batteries than those recommended.

Detection Range

1. Maximum Detection Distance: Sm
2. Maximum Detection Range (Horizontal): 90°
3. Maximum Detection Range (Vertical) : 55°

The data above is obtained from lab experiments conducted under 77°F (25°().

Light Sensor
A Light Sensor is used to detect whether it is bright or dark in the target environment. You can define the threshold for being bright or dark in the app. Navigate to the Settings page of Contact Sensor in the app for more information.

How to Install

Adhere to a door or a window

Peel off the protective film from the Contact Sensor and Magnet.

Line up the Contact Sensor and Magnet on the door or window and make sure the Magnet is aligned with the bottom of Contact Sensor. Stick the Contact Sensor on the door/window and Magnet on the frame or the other way around. Make sure the gap between the sensor and the magnet is less than 30mm when the door or window is closed. Apply pressure to the Contact Sensor and Magnet for 60 seconds so that they are firmly attached.

Mount to a surface using screws

1. Remove the Battery Case from the Contact Sensor. Mount the Battery Case to the target surface using the screws provided. You don’t need to peel the protective film off during this process.
2. Install the Contact Sensor back to the Battery Case, that has been mounted to the target surface.
3. Line up the Contact Sensor and the Magnet on the door or window and make sure the Magnet is aligned with the bottom of the Contact Sensor.
4. Peel the protective film off the Magnet and stick it to the surface near the Contact Sensor. Make sure the gap between the sensor and the magnet is less than 30mm when the door or window is closed.
5. Apply pressure to the Magnet for 60 seconds so it is firmly attached.

Important Notice

• Make sure the target surface is dry and clean.
• Avoid any heat sources, such as light bulbs.
• Avoid facing towards a glass door or window to reduce reflection and interference.
• Avoid facing towards constantly moving objects.

Battery Replacement. Firmware Update and Factory Reset

Battery Replacement
Remove the Battery Case. Follow the”+” and”-” marks, and replace the old batteries with new ones. Put the Battery Case back.

Firmware Update
Please make sure you have the up-to-date firmware by upgrading in time.

Factory Reset
Long press the Reset Button for 15 seconds or until the LED Indicator Light is on.

Note : After the device is reset, all settings will be set to the default values and the activity logs will be erased.

If you see a cloud icon showing up on the Contact Sensor device card, this means it is being scanned by Hub Mini. Navigate to the Settings page of Contact Sensor to enable Cloud Service from there. Scan the QR code below to view more solutions. https://support.switch-bot.com

Specification

• Model Number : W1201500
• Size : 70.5mm x 25.5mm x 23mm (Contact Sensor); 35mm x 12mm x 12.5mm (Magnet)
• Weight : 43g (Contact Sensor with batteries); 13g (Magnet)
• Battery Life : 2 x AAA batteries roughly 3 years (triggered 80 times door open & door close respectively. button press and light sensing 40 times and 20 times by local scenes under 77°F (25°C) by daily use)
• Working Condition : 14°F-140°F (-1 0°c -60°C), 20-85% RH
• Maximum Detection Distance : Sm, results obtained from lab experiments under 77°F (25°C)
• Maximum Detection Range : 90° horizontally and 55° vertically, results obtained from lab experiments under 77°F (25°C)

Return and Refund Policy
This product has a one-year warranty (starting from the purchasing day). The situations below do not fit the Return and Refund Policy.

• Intended damage or abuse.
• Inappropriate storage (drop-down or soaking in water).
• Modify or repair of product.
• Natural wearing of product.
• Natural disasters.

The batteries are not in the warranty.

Contact and Support

• Setup and Troubleshooting:
  support.switch-bot.com

• Support Email:
  support@wondertechlabs.com

• Feedback :
  If you have any concerns or problems when using our products, please kindly send feedback from the Profile> Feedback page in the SwitchBot app.

CE Warning
Manufacturer’s Name: Wean Technology (Shenzhen) Co., Ltd. This product is in a fixed location. To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the user’s body and the device, including the antenna. Use only the supplied or approved antenna. This device is in compliance with the essential requirements and other relevant provisions of Direc­tive 2014/53/EU. All essential radio test suites have been carried out.

1. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DIS- POSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
2. The device complies with RF specifications when the device used at 20cm from your body

FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

FCC RF exposure statement:
The equipment complies with the FCC Radiation exposure limit set forth for uncontrolled environments. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

UKCA DOC
Hereby, Woan Technology (Shenzhen) Co., Ltd. declares that the radio equipment type W1201500 is in compliance with UK Radio Equipment Regulations(SI 2017/1206).

The full text of the UK declaration of Conformity is available at the following internet address: www.switch-bot.com

FAQ’s

Is there any difference in using Contact Sensor on a door or window?

When installed to a window, the motion sensing feature will be automatically disabled because the cool air or hot air may interfere with the bulit-in motion sensor beneath the Reset Button which may trigger false alarms.

How to enable Cloud Service?

You need to purchase a Switch Bot Hub Mini sold separately and set it up under your account. Then navigate to the app Home page.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>