HYCHIKA BB729 HVLP Paint Sprayer Instruction Manual
- June 14, 2024
- HYCHIKA
Table of Contents
HYCHIKA BB729 HVLP Paint Sprayer
Product Information
Specifications
- Model: BB729
- Rated Power: 4.6A
- Rated Voltage: 120V
- Frequency: 60Hz
- Rated Speed: 32000RPM
- Wire Length: 3m
- Spray Distance: 8-10 inches
- Width: 8-12 inches
- Max Viscosity: 80DIN-s
- Tank Capacity: 800ml
Function
The Paint Sprayer BB729 is a versatile tool suitable for various painting
tasks such as furniture, fences, doors, windows, walls,ceilings, car
repairing, and high altitude operations.
Product Usage Instructions
Material Preparation
Before using the electric spray gun, it is important to prepare the
materials properly. Refer to the thinning chart and picture provided in the
user manual.
| Material | Viscosity (DIN-S) |
|---|---|
| Oil enamel | 25-60s |
| Oil-based primer | 30-60s |
| Oil stain | No thinning required |
| Clear sealer | No thinning required |
| Polyurethane | No thinning required |
| Lacquer | 25-30s |
| Varnish | 25-30s |
| Automotive finishes | 20-40s |
| Latex | 45-90s |
Steps to Use the Paint Sprayer
Step 1: Unscrew the paint container
Unscrew the paint container from the spray gun.
Step 2: Adjust the suction tube
- If spraying upward, the inclined end of the straw should point to the back of the gun.
- If spraying downward, the inclined end of the straw should point to the front of the gun.
Step 3: Pour material into the container
Pour the material into the container, making sure not to exceed the maximum capacity of 800ml.
Step 4: Connect the spray gun body to the motor
- Hold the spray gun by hand and align the slot on the spray gun with the slot on the motor. Insert it securely.
Step 5: Adjust the needle adjusting screw
- To decrease paint volume and lower paint thickness, adjust the screw to the left.
- To increase paint volume and increase paint thickness, adjust the screw to the right.
Step 6: Turn on the power switch and spray paint
Turn on the power switch and press the trigger to start spraying paint.
How To Spray Properly
- Correct: Keep stroke smooth and at an even speed.
- Incorrect: Do not flex the wrist while spraying.
FAQ
Q: What should I do if I encounter any problems with the product?
A: If you encounter any problems, please contact our after-sales email at
[email protected] for assistance.
If any problems, please contact our after-sales email: [email protected]
Technical parameters
Model:BB729
Rated power: 4.6A| Spray distance: 8-10 inch
Rated voltage:120V| Width: 8-12 inch
Frequency: 60Hz| Max viscosity: 80DIN-s
Rated speed: 32000RPM| Tank capacity:800ml
Wire length:3m|
Function
Suitable for painting furniture, fences, doors, windows, walls, ceiling, and for car repairing, high altitude operation and, and so on.
How to use
Before use the electric spray gun,material preparation is the first stage. Please refer to the thinning chart and picture.
DIN-S: The time for the liquid to run out of a funnel.
| Material | Viscosity(DIN-S) |
|---|---|
| Oil enamel | 25-60s |
| Oil based primer | 30-60s |
| Oil stain | No thinning required |
| Clear sealer | No thinning required |
| Polyurethane | No thinning required |
| Lacquer | 25-30s |
| Varnish | 25-30s |
| Automotive finishes | 20-40s |
| Latex | 45-90s |
- Unscrew the paint container from the spray gun.
- Adjust the suction tube
- If spraying upward, the inclined end of the straw should point to the back of the gun.
- If spraying downward, the inclined end of the straw should point to the front of the gun.
- Pour material into container, make sure not to exceed 800ml.
- Remove the motor
- Hold the spray gun with your hand.
- At the same time, hold the motor handle by hand and rotate it 90 ° counterclockwise.
- Pull out to remove the motor from the spray gun.
- Connect the spray gun body to the motor
- Hold the spray gun by hand, align the slot on the spray gun with the slot on the motor, and then insert it (as shown in the figure).
- Hold the motor handle by hand and rotate the right hand 90 ° clockwise.
- When the gun is parallel to the main engine, it is locked.
- Adjust the needle adjusting screw to meet your requirement.
- Adjust the screw to left to decrease paint volume, lower paint thickness
- Adjust the screw to right to increase paint volume, increase paint thickness
- Turn on the power switch and press the trigger to spray paint.
How To Spray Properly
EVEN COAT THROUGHOUT
Correct:
Keep stroke smooth and at even speed.
Incorrect:
Do not flex wrist while spraying.
Better Tools for Better Life
If any problems, please contact our after-sales email: [email protected]