RADIOMASTER T8 Lite 2.4g Remote Control System User Manual
- June 6, 2024
- Radiomaster
Table of Contents
T8 Lite
USER MANUAL
WWW.RADIOMASTERRC.COM
Introduction
Thank you for purchasing the RadioMaster T8 Lite 2.4g remote control system.
The system is powerful and versatile and can be used by beginners to
professionals. In order to ensure the correct and safe use of this product,
please read this manual carefully before use. The information contained in
this manual is subject to change without notice.
-RadioMaster team.
Safety notice
Many remote-control models are equipped with powerful motors and sharp
propellers. When using or maintaining models, proceed with caution. When
performing assembly or maintenance, make sure to disconnect the power to the
model and remove the propellers.
Do not operate the T8 Lite remote-control system under the following
conditions:
- In severe weather or strong wind conditions, such as rain, hail, snow, storms, or highly electromagnetic environments.
- In any situation where visibility is limited.
- In areas where people, property, high-voltage power lines, public roads, vehicles, or animals may be present.
- If you feel tired or unwell, or under the influence of drugs or alcohol.
- If the remote control or model seems to be damaged or not working properly.
- In areas with high 2.4GHz interference or where 2.4GHz radio is prohibited.
- When the battery voltage is too low.
- In areas where local regulations prohibit the use of aviation models.
Switches and Functions
Charging Instructions
The T8 Lite has a built-in 1000mah 3.7v Battery. The built in USB-C charger
will charge your batteries by connecting the supplied USB-C cable to any
suitable USB power outlet. We suggest using a regular 1-2amp 5v USB power
adapter.
Charge status and battery Level:
The 5 LEDs below the neck strap loop indicate the charging status. When the
LEDs light up from left to right the T8 Lite is charging. Each of the 5 LEDs
indicates 20% of the battery capacity. 5 LEDs shows 100% charge, 4 LEDs 80%,3
LEDs 60%, 2 LEDs 40%, 1 LED 20%. When the power of the radio is low and the T8
Lite requires charging all 5 battery status LEDs will flash at the same time.
Please recharge the battery before using the radio any further
Status
|
Indicator light
---|---
Power Level| Five indicator lights indicate 0-100% power,and on average each
indicator indicates 20% power
Recharge| The indicator light flashes from 1 to 5 cycles, indicating that it
is charging, and all the indicator lights are always on after the charging is
completed
Power on/off
Power on: Press and hold the power button, the five status LEDs will light up
sequentially followed by a beep. Let go of the power button after you hear the
beep.
Power off: Press and hold the power button, the five status LEDs will turn off
sequentially followed by a beep. Let go of the power button after you hear the
beep.
Default channel order:
CH1 | CH2 | CH3 | CH4 | CH5 | CH6 | CH7 | CH8 |
---|---|---|---|---|---|---|---|
Aileron | Elevator | Throttle | Rudder | SA | |||
2Position | SB | ||||||
3Position | SC | ||||||
3Position | SD |
2Positio
Binding your T8 Lite
Bind mode for D8 protocol receivers
- Turn on the transmitter and keep the throttle at its lowest position. Press and hold the bind button for longer than 1 second, the transmitter will start beeping in a beep-beep-beep pattern, signaling D8 mode. If the transmitter beeps in a beep (x2)-beep(x2)-beep(x2) pattern, this means the transmitter is in D16 mode and the bind button should be pressed momentarily to return to D8 mode.
- Power on the receiver, press the bind button on the receiver within 3 seconds to enter bind mode on the receiver.
- The red light on the receiver will flash, signaling that the unit has bound successfully. Turn the receiver off and on again for the unit to function correctly.
Note: D8 receivers made by different manufacturers may have different binding procedures. Refer to the user manual for precise binding instructions.
Bind mode for D16 protocol receivers
- Turn on the transmitter and keep the throttle at its lowest position. Press and hold the bind button for longer than 1 second, the transmitter will start beeping in a beep(x2)-beep(x2)-beep(x2) pattern, signaling D16 mode. If the transmitter beeps in a beep-beep-beep pattern, this means the transmitter is in D8 mode and the bind button should be pressed momentarily to return to D16 mode.
- Power on the receiver, press the bind button on the receiver within 3 seconds to enter bind mode on the receiver.
- The red light on the receiver will flash, signaling that the unit has bound successfully. Turn the receiver off and on again for the unit to function correctly.
Note: D16 receivers made by different manufacturers may have different binding procedures. Refer to the user manual for precise binding instructions.
Specifications
Size: | 16013045mm |
---|---|
Weight: | 218g |
Frequency: | 2.400GHZ-2.480GHZ |
RF Module: | Multi-Protocol Module Compatible Single-chip(CC2500) |
Protocol Options: | D8/D16 |
Transmission power: | 20dbm |
Antenna gain: | 2db |
Range: | ~1km @ 20dbm (depending on the receiver) |
Battery: | Built-in 3.7v 1000mah Lithium battery |
Charging: | Built-in USB-C charging |
Channels: | Up to 8 channels (depending on the model/receiver) |
Gimbal: | High-precision potentiometer sensor gimbal |
Warranty and Support
If there is any problem with your remote-control hardware, please keep the
proof of purchase and contact the retailer where you purchased the T8 Lite.
Technical support can be found at https://www.radiomasterrc.com Or join our
Facebook group for community support
https://www.facebook.com/radiomasterrc
| EU Simple Declaration of Conformity
RadioMaster declares the radio equipment T8/T8 Pro/T8 Lite is in compliance
with EU directives Directive 2014/53/EU. Full text of the declaration of
conformity is available at the following website
www.radiomasterrc.com
---|---
Manufactured by
Shenzhen RadioMaster Co., Ltd
Address: 5/F, Building 9, De Zhi Gao Technology Park, Yang Tian Road
Baoan District, Shenzhen, 518101, Guangdong, China
| FCC ID: FCC ID: 2AV3G-T8
FCC Information
This equipment has been tested and found to comply with the limits for Part 15
of the FCC rules. This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Full text
of the declaration of conformity is available at the following website
www.radiomasterrc.com
---|---
CAUTION:| Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment. This product contains a radio transmitter with wireless technology
which has been tested and found to be compliant with the applicable
regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz
frequency range.
---|---
Antenna Separation Distance
When operating your RadioMaster transmitter, please be sure to maintain a
separation distance of at least 20 cm between your body (excluding fingers,
hands, wrists, ankles, and feet) and the antenna to meet RF exposure safety
requirements as determined by FCC regulations.
| Visit our website to learn more https://www.radiomasterrc.com/
---|---
| Follow us on Facebook https://www.facebook.com/radiomasterrc/
| Follow us on Instagram https://www.instagram.com/radiomasterrc/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>