THUNDER ET-0040V8-27 Remote Control Car Instruction Manual

THUNDER ET-0040V8-27 Remote Control Car

Thank you!

Thank you for purchasing the Thunder Remote Control Racecar.
This manual provides more information about this RC Car, please read the instructions before using.

Product Overview

• Thunder Remote Control Race car
  

• Remote Controller

• Instruction Manual

Package Contents

Includes:
1 (One) Thunder Remote Control Race car
7.87in. x 3.36in. x 2.36in. (20cm x 8.6cm x 6cm).
1 (One) Wheel Controller
4.25in. x 1.3in. x 9.9in. (10.8cm x 3.3cm x 25.5cm).
1 (One) Instruction Manual

Specifications

Thunder Remote Control Race car
Power supply: 3 x “AA” 1.5V Batteries (alkaline type preferred, not included)
Remote Controller:
Power supply: 2 x “AA” 1.5V Batteries (alkaline type preferred, not included)
Frequency: 27 MHz (Blue)
40 MHz (Red)
49 MHz (Green)

Remote Controller

Standard Control

Note: To avoid losing control, always pay attention when controlling the Remote Control Car.

Control Thunder Remote Control Race car to move forward

Control Thunder Remote Control Racecar to move backward

Standard Control

Control Thunder Remote Control Race car to turn left

Control Thunder Remote Control Race car to turn right

Racing With Friend

Please purchase other car with different frequency to race

Power On/Off

Slide the ON/OFF Switch to ON to tum on the Thunder Remote Control Racecar.
Slide the ON/OFF Switch to OFF to turn off the Thunder Remote Control Racecar.

Batteries Installation For Remote Control Car

To install batteries into the Thunder Remote Control Racecar, unscrew the screw on the battery box cover to open the cover. Insert 3 x “AA” 1.5V batteries (Not Included) into the battery box. Batteries should be placed as shown on the diagram. Replace the battery box cover and tighten the screw.

Notice:

When inserting the batteries, you must insert according to the correct polarity, the Thunder Remote Control Racecar woo, function if batteries are reversed.

Batteries Installation For Remote Controller

To install batteries into the Remote Controller, unscrew the screw on the battery box cover to open the cover. Insert 2 x “AA· 1.5V batteries (Not lidded) into the battery box. Batteries should be placed as shown on the diagram. Replace the battery box cover and lighten the screw.

Notice:

When inserting the batteries, you must insert according to the correct polarity, the Remote Controller wont function if batteries are reversed.

Performance Tips

1. Do not drive the Thunder Remote Control Racecar on grass, sand or go through water.
2. Do not drive the Thunder Remote Control Racecar in windy or rainy weather.
3. Do not drive the Thunder Remote Control Racecar into any sharp object.
4. Keep fingers, hair and loose do thing away from Thunder Remote Control Racecar.

Care and Maintenance

Always use dry and soft cloth to clean this product.
Avoid this product from being exposed to sunlight or heat.
Avoid immersing these toys in water, otherwise, the electronic parts may be damaged.
Check the product regularly. If any damages are discovered, please stop using immediately, until it is completely repaired in good working condition.

IMPORTANT: BATTERY INFORMATION

For AA Batteries

WARNING:TO AVOID BATTERY LEAKAGE

1. Be sure to insert the batteries correctly, and always follow the toy/game and battery manufacturers’ instructions.
2. Do not mix old and new batteries or alkaline. standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
3. Always remove weak or dead batteries from the product.
4. Remove the battery if the product is is left unused for a long period of time.

Warning

This product is suitable to be used by people who has operating experience in remote toy or aged no less than 8 years old.
Please do not put the product in your mouth to prevent choking hazard of small parts.
Please do not put the finger into available interspaces.
Please do not play the product in a brutal way such as throwing, crashing or twisting it.
Please store the smaller-sized product accessories in places that are out of reach of children, in order to avoid the occurrence of accidents.
Avoid placing the batteries in places in high temperatures and avoid exposure to heat When young children are operating the product, it shall be ensured that the adults are guiding and making sure the product control is within the viewing range of the controller (or instructor) so that it makes the control of the toy more convenient When the product is not in use, please switch off the power supplies of the toy, and remove the batteries from the product.
Please note that we wont take any responsibility for any wrong operation as this may result in severe injury or loss of property, and we cannot control the operating process during the time when the user assembles or uses this product.
Once this product is sold, we won l be responsible for any safety responsibility during the time the user operates or uses controls this products.

FCC Statement

This device complies with the part 15 of the FCC rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: changes or notifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/ TV technician for help.

RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC ID: 27 Mhz: 2ADM5-ET-0040V8-27
40 Mhz: 2ADM5-ET-0040V8-40
49 Mhz: 2ADM5-ET-0040V8-49

Distributed by 1616 Holdings, Inc.
701 Market Street, Suite 200
Philadelphia, PA 19106
Made In Shantou, China
Keep All Relevant Information for Future Reference Item# ET-0040-VS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>