Whynter BOR-326FS Indoor Outdoor Beverage Refrigerator Instruction Manual

Whynter BOR-326FS Indoor Outdoor Beverage Refrigerator Instruction Manual

Safety Precautions

APPLIANCE SAFETY
Your safety and the safety of others are very important to us.

To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic precautions

⚠ This is the Safety Alert Symbol. This symbol alerts you to potential hazards that may result in serious injury. All safety messages will follow the Safety Alert Symbol and either the words” DANGER” or “WARNING”.

⚠DANGER⚠ Danger means that failure to heed this safety statement may result in severe injury or death.

⚠ WARNING ⚠ Warning means that failure to heed this safety statement may result in extensive product dam-age, serious injury, or death.

CAUTION Caution means that failure to heed this safety statement may result in minor or moderate injury, or property or equipment damage.

All safety messages will alert you to know what the potential hazard is, tell you how to reduce the chance of injury, and let you know what can happen if the instructions are not followed.

IMPORTANT SAFEGUIDES
⚠ Before the appliance is used, it must be properly positioned and installed as described in this manual, please read the manual carefully. To reduce the risk of fire, electrical shock or injury when using the appliance, follow basic precaution, including the following:

⚠DANGERA⚠

• Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do not use an extension cord.

• Do not use if the power supply cord is damaged. If damaged, it must be replaced by a qualified electrician.

• It is recommended that a separate circuit, serving only your appliance be provided. Use receptacles that cannot be turned off by a switch or pull chain.

• Never clean appliance parts with flammable fluids or harsh chemicals. These fumes can create a fire hazard or explosion.

• Do not store or use gasoline or other flammable vapours and liquids in the vicinity of the appliance or any other appliance.

• Before proceeding with cleaning and maintenance operations, make sure to unplug the appliance.

• Do not connect or disconnect the electric plug with wet hands.

• Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.

• This appliance is intended for use in residential applications and should not be used in a commercial setting.

• In the event of leakage:
  – Disconnect from the mains
  – Air the room in which the appliance is located for several minutes and contact the Service Department for advice
  ⚠ WARNING⚠

• Use two or more people to move and install the appliance. Failure to do so can result in injury.

• All repairs, disassembly and modifications should be performed only by qualified technicians. Attempting to perform this yourself could result in fire, malfunction or injury.

• Never splash water directly onto the product or wash it with water without unplugging, as a short circuit could result.

• Never put flammable or volatile substances into the unit as explosion and fire could result.

• To ensure proper ventilation for your appliance, the front of the appliance must be completely unobstructed.
  Choose a well-ventilated area with temperatures above 60 ° F (16° C) and below 90 ° F (32 ° C). This appliance must be installed in an area protected from the element, such as wind, rain, water spray or drips.

• The appliance should not be located next to ovens, grills or other sources of high heat.

• The appliance must be installed with all electrical connections in accordance with state and local codes.

• The fuse (or circuit breaker) size should be 15 amperes.

• Use a dedicated wall outlet. Do not use an extension cord or multiple-outlet adapter as this could result in electrical shock, overheating and fire.

• It is important for the appliance to be levelled in order to work properly. For a stable installation, make sure the appliance is placed on a flat, level and solidsurface.

• Ensure that the surface on which the appliance is placed is strong enough to hold the appliance and the items stored inside.

• This appliance is not intended for use by young children or physically-challenged persons without supervision/assistance. Young children must be supervised to ensure safety around this or any appliance.

• Do not use solvent-based cleaning agents of abrasives on the interior. These cleaners may damage or discolour the interior.

• Keep fingers out of the “pinch point” areas. Clearance between the door and cabinet are necessarily small.
  Be careful closing the door when children are in the area.

• This appliance is designed for storing and cooling beverages. If food is stored inside, ensure that there is sufficient airflow between items. Please note that the temperature range for this appliance is optimized for beverage storage. Perishable food items may require a different storage environment.

• Do not place hot food or beverages into the appliance.

•  Close the beverage refrigerator door immediately after putting in any items to keep the internal temperature relatively constant.

• Avoid placing any objects on top of the appliance.

• This is an electrical appliance, to avoid injury from electrical shock do not operate the unit with wet hands, while standing on a wet surface or while standing in water.

• When positioning or moving the appliance, ensure that it is not turned up side down or unlevelled greater than 45 °

• Never pull the power cord to disconnect it from the outlet. Grasp the plug and pull it from the outlet.

•  Never lift, carry or drag the appliance by the power cord.

• This appliance is designed for household, non-commercial use only. Any other use will void the warranty.

• Do not move this appliance without emptying it and securing the door in a closed position.

• Do not plug into the power outlet before set up is completed.

• Do not damage, modify, excessively bend, strain, twist or bundle the power cord. Also, placing heavy objects on the power cord or binding it could damage the cord, possibly resulting in electrical shock or fire.

• Repair or replace any cord that is frayed. Do not use a cord that shows cracks or abrasions along its length.

Parts

Product Features

Ideal for your outdoor kitchen or a patio bar, the Whynter BOR-326FS Indoor/Outdoor Stainless Steel Refrigerator can just as easily be the featured in your indoor entertainment space.

Manufactured with premium components and materials, this well-appointed refrigeration unit enhances any setting and is built to maintain temperature requirements under a wider range of ambient conditions. The full stainless steel exterior provides both high end appeal and superior temperature control.

The unit features a front venting design for either freestanding or built-in usage, reversible door hinges for easier installation options and adjustable shelving to accommodate beverage cans, bottles or foodstuff.

• Full Stainless steel body
• Built-In Installation / Freestanding
• Indoor/Outdoor use
• Luxurious curved handlebar
• Reversible door swing
• 1 large, 2 medium, and 1 small shelf
• ETL + ETL-S® Sanitation Certified
• Energy Star Certified

TECHNICAL PATA

Installation

IMPORTANT SAFETY INSTRUCTIONS
⚠ WARNING
To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic precautions:

• Read all instructions before using the appliance.

  • DANGER or WARNING: An empty appliance can be a hazardous for children or small pets. If disposing of the appliance, remove gasket seals, latches, lids or the entire door to ensure the appliance is harmless.

• Never allow children to operate, play with, or crawl inside the appliance.

• Never clean appliance parts with flammable fluids or harsh chemicals. The fumes can create a fire hazard or explosion.

• Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other appliance.
  The fumes can create a fire hazard or explosion.

• Do not use any electrical appliances within the inside of the refrigerator, unless approved by the appliance’s manufacturer.

• Follow ventilation space requirements and ensure the vents are not blocked or covered.

• Do not use mechanical devices to accelerate the defrosting process. Refer to the recommended defrost process.

• Do not damage or alter the refrigeration circuit lines or the compressor.

INSTALLATION INSTRUCTIONS

BEFORE USING YOUR APPLIANCE

• Remove the exterior and interior packing.
• Before connecting the appliance to the power source, let it stand upright for approximately 4 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.
• Clean the interior surface with lukewarm water using a soft cloth.

INSTALLATION OF YOUR APPLIANCE

• The appliance is designed for built-in, recessed or freestanding installation.
• CAUTION: This appliance is designed for storing and cooling beverages. Do not store perishable food, medicine or other medical products.
• Place your appliance on a hard and level floor that is strong enough to support it when it is fully loaded.
• We do not recommend installing the appliance on carpet.
• To level your appliance, adjust the leveling legs at the bottom of the appliance if needed.
• For freestanding installation, 5 inches (127mm) of space between the back and sides of the appliance are suggested, which allows the proper air circulation to cool the compressor and condenser. Even for built-in installation, it is a must to keep a¼” (6.35mm) space on each side and at the top. And the air vent at the front of the appliance must never be covered or blocked in any way.
• NOTE: Do NOT install the appliance near an oven or other heating source. Heat sources may increase electrical consumption. For best performance, do not install the appliance behind a cabinet door or black the base grille.
• Avoid locating the appliance in area that may be exposed to excessive moisture.
• In a rainy or snowy environment, a waterproof covering is recommended.
• Never climb onto the unit. The unit could tip over or fall and cause material damage or personal injury.
• Plug in the appliance into an exclusive, grounded wall power outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a qualified electrician or an authorized service center.

BUILT-IN CABINET INSTRUCTIONS
These appliances are designed for both built-in or freestanding installation. For built-in installation, ensure proper service access and ventilation, allow at least¼” space on each side and at the top.

⚠ WARNING: Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by a qualified electrician or contact Whynter Service Department.

ELECTRICAL CONNECTION
This appliance requires a standard 115/120 Volt AC ~/60Hz electrical ground outlet with three-prong. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental injury.

The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance. This provides the best performance and also prevent overloading house wiring circuits that could cause a fire hazard from overheated. Never unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the appliance, be careful not to damage the power cord.

If installation in a damp location is unavoidable, have an electrician install a ground fault circuit interrupter (GFCI) electrical outlet. If no GFCI is installed, electrical shock could result.

EXTENSION CORP
Because of potential safety hazards, it is strongly recommended that you do not use an extension cord with this appliance. However, if you must use an extension cord, it is absolutely necessary that it be a UUCUL Listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes.

REVERSING THE DOOR SWING OF YOUR BEVERAGE OUTDOOR REFRIGERATOR Tools needed: Flathead screwdriver, Phillips screwdriver
IMPORTANT: Before you begin, unplug the refrigerator or disconnect power.

To remove door from hinges:

1. Using a flathead screwdriver, separate the hinge axis from hinge #1. Set aside.
2. Open the door about 20° around the axis of bottom hinge #2, then lift the door off bottom hinge #2 and set door aside.

To replace door on hinges:

1. Open the door and remove the door hole cover from the door top(Fig. A).

2. Remove two screws(1) from the lower hinge (2) of the door, remove the door(3) off from the upper right hinge.
   Remove the lower hinge and relocated it to the left side (Fig. B-1 to B-3).

3. Remove three screws from the upper right hinge(Fig. C) .

4. Remove the three screw hole covers item 6 from the top left of the cabinet(Fig. D)and install the three screw hole covers at the top right of the cabinet where the original upper right hinge was removed.

5. Install upper left hinge(4) with the three screws removed from the upper right hinge(Fig. E).

6. Install the door(3) by sliding it onto the upper left hinge pin, then secure the lower hinge pin(2) by using the screws(1) removed in step 2(Fig. F).

7. Install the door hole cover into the top right door hinge hole.

REVERSING THE DOOR HANDLE OF YOUR BEVERAGE OUTDOOR BEEBIGEBAJCB
Using a Phillips screwdriver, remove the two screws pre-installed on the left side of the door. The door has two screw holes on the rear side allowing you to install the handle. Align the handle with the screw holes and attach with the two screws. Tighten screws firmly but do not over tighten.

Operation and Controls

It is recommended you install the appliance in a place where the ambient temperature is between 72°- 78°F / 23°- 260C. If the ambient temperature is above or below recommended temperatures, the performance of the beverage refrigerator may be affected. For example, placing your appliance in extreme cold or hot conditions may cause interior temperatures to fluctuate.

NOTE:

• When using the beverage refrigerator for the first time or restarting after being shut off for a long period of time, there may be a few degrees variance between the set temperature and the LED readout. This is normal due the length of activation time. The unit should return to normal after running for a few hours.
• It is normal for there to be a temperature variance of 1 °-5° of the set temperature. This unit will not raise its internal temperature if the ambient temperature where the unit is located is lower than the set temperature.

CONTROL PANEL GUIDE

°F/°C SELECTOR
Select the temperature display setting in Fahrenheit or Celsius degree. To change the temperature from Fahrenheit to Celsius or from Celsius to Fahrenheit, press and hold the LIGHT key for 5 seconds.

WIRE SHEL,\/ES
NOTE: Do not cover any part of the wire shelves with aluminum foil or any other material that will prevent adequate air circulation within the cabinet .

This appliance is equipped with 1 large, 2 medium, and 1 small shelf. To prevent damage to the door gasket, make sure the door is opmed completely before pulling the shelves out.

• For easy access, shelves must be pulled approximately½ out of the railing.
• The shelves are designed with an emergency stop to prevent them being removed too far when loaded.
• When removing the shelves out of the railing, make sure to remove all items first.

To remove the shelves, pull the shelf forward until the notch aligns with the plastic post. Lift the shelf and to pull the shelf forward until it is completely removed from the internal compartment.

NORMAL SOUNDS
The unit is cooled by a compressor. The compressor pumps coolant through the cooling system, producing operating noise. Even when the compressor cuts out, noises caused by changes in temperature and pressure are unavoidable. Operating noise will be most audible immediately after the compressor comes on. It becomes quieter as the operating period continues.

The following noises are normal and occur from time to time:

• Gurgling sound, caused by the refrigerant flowing through the appliance’s coils,
• Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on.
• Cracking/popping sounds, resulting from the materials contraction and expansion due to temperature variations,
• Fan operating sound, to circulate the air within the beverage cabinet.
• Unusual noise is normally the result of improper installation.
• Where the unit is installed in open-plan kitchen or in partition walls, the level of operating noise will be heard more acutely. However, this is due to the surrounding architecture and not to the unit.

NOTE: An individual’s perception of noise is directly linked to the environment in which the unit is located, as well the specific type of models. Our appliances are in line with international standards for such appliance and in line with the latest technical developments. Please remember that the noise of the compressor and the coolant circulating in the system is unavoidable.

CONTENT STORAGE

Care and Maintenance

CLEANING YOUR APPLIANCE

• Turn off the power, unplug the appliance, and remove all contents from the appliance and store them in a suitable place.
• Clean the inside, the door seal and the inside of the glass with a clean, damp cloth.
• Never use detergents or other substances that emit Odors.
• Always keep the door closed when cleaning the outside of the appliance. Make sure no detergent Odors penetrate into the appliance.
• Clean the side panels and door surfaces with a clean and soft cloth. If necessary, use a moist cloth. Alternatively, use a microfiber cloth.
• The humidity tray should be handwasher with water and detergent. After cleaning, always make sure the tray is thoroughly rinsed with clean water before replacing.

PREMISES POWER FAILURE

• In the event of a power interruption, temperature settings automatically defaults to factory settings once power is restored.
• Factory default temperature setting is 40° F. To set a different desired temperature, refer to the “SETTING THE TEMPERATURE” and “°C and ° F SELECTOR” section on page 10.
• Most power failures are corrected within a few hours and should not affect the temperature of your appliance if you minimize the number of times the door is opened. If the power is going to be off for a longer period of time, you need to take the proper steps to protect your contents.

VACATION TIME

• Short vacations: Leave the appliance operating during vacations of less than two days.
• Long vacations: If the appliance will not be used for an extended period, remove all items and turn off the appliance. Clean and dry the interior thoroughly.

MOVING YOUR APPLIANCE

• Remove all items inside the appliance.
• Securely tape down (we recommend using painter’s tape) all loose items (shelves) inside your appliance.
• Turn the adjustable legs up to the base to avoid damage.
• Remove all wheel casters.
• Tape (we recommend using painter’s tape) the door shut.
• Be sure the appliance stays secure in the upright position during transportation and protect the exterior of appliance with a blanket, or similar item.

PREPARING FOR STORAGE
If the beverage refrigerator will not be used for a long time, or is to be moved to another place, it will be necessary to defrost the unit and dry the interior.

1. Disconnect the beverage refrigerator from the power supply by removing the power plug from the wall socket.
2. Leave the door open to allow for air circulation and to prevent mold, mildew and unpleasant smells.
   CAUTION: Store the unit out of the reach of children. If you have children, you may want to take additional precautions such as removing the door to prevent a child from being trapped inside the beverage refrigerator

NOTE:

• If the beverage refrigerator is unplugged, encounter power lost, or turned off; you must wait 3 to 5 minutes before restarting the beverage refrigerator.
• When the beverage refrigerator is used for the first time or restarted after having been shut off for a long time, there could be a few degrees variance between the temperature you select and the one indicated on the display. This is normal and it is due to the length of the inactivation time.

ENERGY SAYING TIPS

• The appliance should be located in the coolest area of the room or outside location, away from heat producing appliances, and out of any direct sunlight.
  • Ensure that the appliance is adequately ventilated. Never obstruct the air vents.
  • Close the door tightly and do not open the appliance too frequently or for a long period of time.
  • Store the content in an organized way.
  • Do not over load the appliance to allow air to circulate.

TRANSPORT OF THE BEVERAGE REFRIGERATOR
The ideal packaging for the beverage refrigerator is its original packaging. Please keep the original packaging handy and repack the beverage refrigerator if you need to transport the unit.

DEFROSTING
The unit uses an automatic defrost system in which the refrigerated surfaces of the unit defrost automatically.
Defrost water drains into a hole in the floor of the storage compartment and is channelled into a drain pan located at the back of the unit near the compressor. Heat transferred from the compressor evaporates any water that has collected in the pan. Be sure the drain hole in the floor of the unit is clear and unobstructed.

Troubleshooting

ONE YEAR LIMITED WARRANTY

This WHYNTER product is warranted to the original owner, purchased from an authorized Whynter dealer within the 48 U.S. continental states, for one year from the original purchase date against defects in material and workmanship under normal residential usage. Should your WHYNTER product prove defective within one year from the date of purchase, contact Wynter’s Customer Support Team with the serial number and proof of purchase to make a warranty claim. A Return Authorization Number must be issued before returning any parts or products. Parts or products received without a Whynter issued Return Authorization Number will be refused.
Under this warranty, Whynter will repair or replace any parts found defective with new or remanufactured parts or exchange the defective product with a new, refurbished, or remanufactured product at our discretion. All defective products and parts covered by this warranty will be repaired or replaced on a mail-in basis to Wynter’s Service Center. This warranty is not transferable. After the expiration of the warranty, the cost of labor and parts will be the responsibility of the original owner.
Return freight is prepaid by Whynter within two months of purchase. After two months to one year, the customer will be responsible for the return freight cost to Wynter’s Service Center. Please package the product carefully in its original packaging to avoid damage in transit. Whynter is not responsible for damage resulting from shipper mishandling or improper packaging. Please retain the original box and packaging materials.

THIS WARRANTY DOES NOT COVER:

• Acts of God, such as fire, flood, hurricanes, earthquakes and tornadoes .
• Improper power supply such as power surge, low voltage, defective household wiring or inadequate fuses .
• Use in commercial or industrial applications .
• Damage, accidental or otherwise, to the WHYNTER Beverage Refrigerator while in the possession of a consumer not caused by a defect in material or workmanship
• Damage caused by consumer misuse, tampering, or failure to follow the maintenance or care and special handling provisions in the instructions.
• Damage to the finish of the case, or other appearance parts caused by wear .
• Damage caused by repairs or alterations to the product by anyone other than authorized by the manufacturer.
• Removal, Replacement Packaging, Freight and Insurance cost for the warranty service .

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. WHYNTER SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

The warranty, product contents and specifications are subject to change at any time without notice; please refer to www.whynter.com for the most current information.

To register your warranty, please visit www.whynter.com and fill out the on line Warranty Registration form. Please be sure to include a copy of your purchase invoice.
To obtain service or information, contact Whynter LLC via email at support@whynter.com or call 866-WHYNTER (866-949-6837).
Copyright© 2022 Whynter LLC
www.whynter.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>