Yuusei DJ Lights with Stand RGB Party Bar Light Set User Manual
- June 14, 2024
- Yuusei
Table of Contents
Yuusei DJ Lights with Stand RGB Party Bar Light Set User Manual
Party Set USB
USER MANUAL
Unpacking Instructions
Read Manual before Operation
Dear user,
Thanks for choosing our Mix LED- laser device, believing this brand new
product will bring you unlimited marvel and happiness
Before operating this device, please read this manual thoroughly, and retain
it for future reference.
Warning Data
Please note the warnings in bold which will ensure the safe and smooth operation. These warnings are important to a certain extent.
Attention! Indicates a skill or other useful information for special situations.
Important! Indicates important information to protect personnel from laser incident or injury.
Caution! Prevent damage or injury from incorrect operation.
Warning!
If the external flexible cable or cord of this luminaire is damaged, it shall be replaced by aspecial cord or cord exclusively available from the manufacturer or his service agent. Shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for example by cracks or deep scratches.
The lamps shall be changed if it has become damaged or thermally deformed.
Unpacking Instructions
As receiving a fixture, carefully unpacking the carton, checking contents to ensure that all parts are in good condition. Informing the shipper immediately and retaining packing material for inspection if any parts damaged from shipping or device damaged. Keeping packing materials as evidence for shipper’s confirmation.
Attention!
This unit is in perfect condition before delivery, please check all accessories when unpacking the unit. User should follow this user manual to operate this unit, and make sure that you are clear on all laser safety information and unit operation before power it on. Any wrong operation will make this unit out of warranty.
Carefully moving after receiving it, checking whether there is any damage from shipping, and all the accessories in it.
Safety Instructions
Safety Instructions
To protect the environment, please try to recycle the packing material as much as possible.
The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other fluids, or metallic objects.
Don’t throw this product away just as general trash, please deal with the product follow the abandon electronic product regulation in your country.
Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture must be fixed at least 20cm from surrounding walls.
- To avoid condensation to be formed inside, allow this unit to adapt to the surrounding temperatures when bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause damages.
- Don’t cover any ventilation openings as this may result in overheating.
- Don’t install it on flammable object.
- Don not use it when maximum ambient temperature is higher than 40 degree.
- Unplug the unit when it is not used for a longer time or before replacing the bulb.
- Don’t open the top cover to avoid unit damage.
- Please use the original packing when the device is to be transported.
Never expose the lens to direct sunlight, even for a short period, this may damage the light effect or even cause fire!
Overhead Rigging & Product Installation
Attention! The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and /or damage to property. Overhead rigging required extensive experience! Working load limits should be respected, Certified installation materials should be used, the installed device should be inspected regularly for safety.
- Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
- Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The fixture must be fixed at least 50cm from surrounding walls
- The device should be installed out of reach of people and outside areas where persons may walk by or be seated.
- The device should be well fixed; a free swinging mounting is dangerous and may not be considered!
- Do not cover any ventilation opening as this may result in overheating
- Before the first time use, it must be inspected by professional staff to make sure safety, inspection regularly every year.
Before rigging make sure that installation area can hold the 10 times weight of device. Using the steel rope which can hold 12 times weight of device, through the eye-bolt for assisting hang installment.
AC Power
Please use the attached power, note that power voltage and frequency are the same as the marked voltage and frequency of device when connecting power. Every device’s power should be connected separately, so that device can be controlled individually.
Cable spec.:
Product Installation
DMX-512 connection
- Connection between laser lights and DMX must use the shied cable of diameter more than 0.5mm. Please use the attached 3 pin XLR plug/socket to connect the DMX output/input interface. The connection between socket and cable as below( note the plug/socket’s 3 pin number and position).
- Note, XLR plug/socket’ s 3pin can not be touched by inner hull, connection between pins is not allowed. Except above connection, XLR plug/socket can not be connected with XLR control line. Device receives international standard DMX512(1990) control signal.
- When using standard DMX512 control signal, the last device’s output interface must be connected to a DMX plug. This plug is putting a 120 ohm resistance between “canon” plug’ s 2 pin and 3 pin. Showing as below pic. Sticking this plug into the last device’s signal output interface, it will avoid the interference during the process of signal transmission.
Operation Instructions
Menu Operating Instruction
-
The keys description:
-
Menu description
Notes:
- The LED screen will flash once no signal detected when operating at SLAVE and DMX mode.
- The fixture will automatically save after one second while press the button.
- When switch on the power with “ENTER” button pressed and held, the unit will go in the programing mode for the firmware updating over DMX interface. Now the LED screen shows “DLOD” and waiting 30s for the updating, then it will run the on board program if nothing occurs. Please follow strictly the update procedure.
IR Remote Control
DMX Assignment
05CH Mode
09CH Mode
36CH Mode
Specification
- Party Set USB supports any combination of 10 different effect lights. Plug and play, intelligent control.
- The T-Bar includes 20 AUTO shows and 20 Sound shows with various speed settings to get the best effect.
- The party set provides you 4 DMX channel modes (5/9/36CH) to make you easier for the show programming and more control possibilities.
- All supported effect light units are powered by Micro-USB interface and can be operated the unit in standalone mode. Auto show and Sound activated shows are available.
- The height of the stand is adjustable, up to 2 meters
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>