Hera OL RGB CCT Dimming 3 Channel LED RF Controller User Manual
- June 14, 2024
- Hera
Table of Contents
RGB/CCT/Dimming 3 Channel LED RF Controller
Model No.: OL/RGB/96/CS/RF
3 Channels/Step-less dimming/Wireless remote control
Auto-transmitting/Synchronize
Features
- Match with RF 2.4G single zone or multiple zone single color, dual color and RGB/RGBW remote control.
- One RF controller accept up to 10 remote control.
- 4096 levels 0-100% dimming smoothly without any flash.
- When using with RGB light, built in 10 dynamic mode, include jump or gradual change style.
- Auto-transmitting function: Controller automatically transmit signal to another controller with 30m control distance.
- Synchronize on multiple number of controllers.
- Light on/off fade time 3s selectable.
Technical Parameters
Input and Output
| Input voltage | 1 2 -2 4 VDC |
|---|---|
| Input current | 12.5A |
| O utput voltage | 3 x (12-24)VDC |
| Output current | 3CH,4A/CH |
| Output power | 1 4 4 -2 8 8 W (1 2 -2 4 V) |
| Output type | Constant voltage |
Environment
| Operation temperature | Ta: -30 ºC ~ +55 ºC |
|---|---|
| Case temperature (Max.) | Tc: + 85 ºC |
| IP rating | IP20 |
Warranty and Protection
| Warranty | 5 years |
|---|---|
| Protection | Reverse polarity Short circuit |
Dimming data
| Input signal | RF 2.4GHz |
|---|---|
| Control distance | 30m(Barrier-free space) |
| Dimming gray scale | 4096 (2^12) levels |
| Dimming range | 0 -100 % |
| Dimming curve | Logarithmic |
| PWM Frequency | 1000Hz (default) |
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
---|---
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED
Weight
| Gross weight | 0.038 kg |
|---|---|
| Net weight | 0.049 kg |
Mechanical Structures and Installations
Wiring Diagram
- V3 for RGB
- V3 for dual color
- V3 for single color
Match Remote Control (two match ways)
End user can choose the suitable match/ delete ways. Two options are offered for selection
Use the controller’s Match key
Match:
Short press match key, immediately press on/off key (single zone remote) or
zone key (multiple zone remote) on the remote.
The LED indicator fast flash a few times means match is successful.
Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast
flash a few times means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power of the receiver, then switch on power.
Repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power of the receiver, then switch on power.
Repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
Application notes
-
All the receivers in the same zone.
RF remote
Auto-transmitting: One receiver can transmit the signals from the remote to another receiver within 30m, as long as there is a receiver within 30m, the remote control distance can be extended.
Auto-synchronization: Multiple receivers within 30m distance can work synchronously when they are controlled by the same remote, under same dynamic mode and with same speed.
Receiver placement may offer up to 30m communication distance. Metals and other metal materials will reduce the range.
Strong signal sources such as WiFi routers and microwave ovens will affect the range.
We recommend for indoor applications that receiver placements should be no further apart than15m. -
Each receiver(one or more) in a different zone, like zone 1, 2, 3 or 4.
Light on/ off fade time
Long press match key 5s, then short press match key 3 times, the light on/off
time will be set to 3s, the indicator light blink 3 times.
Long press match key 10s, restore factory default parameter, the light on/off
time also restore to 0.5s.
RGB Dynamic mode list
| No. | Name | No. | Name |
|---|---|---|---|
| 1 | RGB jump | 6 | RGB fade in and out |
| 2 | RGB smooth | 7 | Red fade in and out |
| 3 | 6 color jump | 8 | Green fade in and out |
| 4 | 6 color smooth | 9 | Blue fade in and out |
| 5 | Yellow cyan purple smooth | 10 | White fade in and out |
Dual color control
CH1 =Wa rm white LED
CH2 =Cool white LED
Each channel can supply up to 9 6 W (@ 24V) and white balance can be
controlled as such:
| Color temperature | Cool white | Neutral white | Warm white |
|---|---|---|---|
| Power distribution | CH1=0W ,CH2=96W | CH1=48W ,CH2=48W | CH1=96W ,CH2=0W |
Malfunctions analysis & troubleshooting
| Malfunctions | Causes | Troubleshooting |
|---|---|---|
| No light | 1.No power. | |
| 2.Wrong connectionor insecure | 1. Check the power. |
2. Checkthe connection
W rong color| 1. Wrong connection of R/G/B wires.| 1. Reconnect R/G/B wires.
Uneven intensity between front and
reacwith voltage drop| 1. Output cable is too long.
2. Wire diameter is too small.
3. Overload beyond power supply capability
4. Overload beyond controller capability| 1. Reduce cable or loop supply
2. Change wider wire.
3. Replace higher power supply
4. Add power repeater.
No response from the remote| 1. The battey has no power
2. Beyond controllable distance.
3. The controller did not match the remote| 1. Replace battery.
2. Reduce remote distance.
3. Re-match the remote
FCC Warning
15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>