Sweetcrispy D-THO-5524 Electric Standing Desk Instruction Manual
- June 14, 2024
- Sweetcrispy
Table of Contents
- D-THO-5524 Electric Standing Desk
- Electric Standing Desk
- Instruction Manual
- Specifications
- Step 1: Supplied Parts and Hardware
- Product Usage Instructions
- Step 1: Assembling the Desk Frame
- Step 2: Attaching the Desk Tabletop
- Step 3: Connecting the Control Panel
- Step 4: Powering the Desk
- Step 5: Operating the Electric Standing Desk
- Q: What is the maximum load capacity of the electric standing
- Q: Can I adjust the speed of the desk’s height adjustment?
D-THO-5524 Electric Standing Desk
Electric Standing Desk
Instruction Manual
D-THO-5524
Specifications
- Max. Speed: 24mm/s
- Operating Noise: (Not specified)
- Max. Load: (Not specified)
Step 1: Supplied Parts and Hardware
Before assembling the electric standing desk, ensure that you
have received all the necessary parts and hardware. The following
items should be included in the package:
- Desk frame
- Desk tabletop
- Control panel
- Screws
- Allen wrench
- Power cord
- Assembly instructions manual
Product Usage Instructions
Step 1: Assembling the Desk Frame
Begin by unpacking the desk frame and identifying the different
components. Follow the assembly instructions manual to connect the
different parts of the desk frame using the provided screws and
Allen wrench. Ensure that all connections are secure.
Step 2: Attaching the Desk Tabletop
Once the desk frame is assembled, place the desk tabletop on top
of the frame, aligning the mounting holes. Use the screws provided
to attach the tabletop to the frame. Make sure the tabletop is
centered and securely fastened to the frame.
Step 3: Connecting the Control Panel
Locate the control panel and connect it to the designated port
on the desk frame. Ensure that the connection is secure and the
control panel is positioned in a convenient location for easy
access.
Step 4: Powering the Desk
Plug the power cord into a power outlet and connect the other
end to the desk’s power input port. Make sure the power cord is not
tangled or stretched, and that it is safely routed away from foot
traffic.
Step 5: Operating the Electric Standing Desk
Once the desk is powered, use the control panel to adjust the
desk’s height. Press the up or down buttons to raise or lower the
desk respectively. The desk should smoothly transition to the
desired height. Release the button to stop the movement. Avoid
exceeding the maximum load capacity of the desk to prevent any
damage.
Frequently Asked Questions (FAQ)
Q: What is the maximum load capacity of the electric standing
desk?
A: The maximum load capacity of the electric standing desk is
not specified in the manual. However, it is recommended to avoid
exceeding heavy loads and follow any weight restrictions provided
by the manufacturer.
Q: Can I adjust the speed of the desk’s height adjustment?
A: No, the speed of the desk’s height adjustment is fixed at
24mm/s and cannot be adjusted.
Electric Standing Desk
Instruction Manual
D-THO-5524
Specifications
Height Adjustment Range 28.7″48″ (73122cm)
Power Input 100V240V
Step 1 Supplied Parts and Hardware
Max. Speed Operating Noise Max. Load
24mm/s
<55dB
176 lbs / 80kg
01 X1
02 X1
03 X1
Crossbar
04 X1
Left Desk Leg
M-A X1
Right Desk Leg
M-B X6
Transmission Rod
Set Screw
Bolt
M-E X1
M-F X1
Small Allen Wrench 3/32″ (2.5mm)
Large Allen Wrench 3/16″ (5mm)
Step 2 Supplied Parts and Hardware
05 X2
M-B X4
Side Plate
Bolt
Step 3 Supplied Parts and Hardware
06 X2
M-C X8
Leg Base
Bolt
M-F X1
Large Allen Wrench 3/16″ (5mm)
M-F X1
Large Allen Wrench 3/16″ (5mm)
Step 4 Supplied Parts and Hardware
07 X1
A X4
Desktop
08 X2
Wood Dowel Pin
09 X1
Headset Hook
C X10
Controller
M-G X8
Rubber Pad
Screw
Step 5 Supplied Parts and Hardware
10 X1
11 X2
AC Adapter
Cable Clip
Step 6 Supplied Parts and Hardware
12 X2
Cable Hole Cover
B X4
Desktop Panel Connector
M-D X14
Screw
Setting the Desk Legs to the Same Height
HEAVY! You may need assistance with this step.
04 03
Fig 1 a
Turn clockwise b Right Leg
Fig 2
a Turn anti-clockwise
b Right Leg
Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the right leg. Turn the rod to adjust the right leg so it’s level with the left leg. Turn the rod clockwise to lower the right leg or anti-clockwise to raise it.
Step 1 Setting the Desk Legs to the Same Height
04 02
04 02
M-E M-A 02 04
04 03
04 03
M-F M-Bx6
01
01
Step 2 Setting the Desk Legs to the Same Height
05 05
You may need assistance with this step.
05 M-Bx4
Step 3 Attaching the Leg Bases
M-F M-CX8
C 06
06 06
Step 4 Assembling and Attaching the Desktop
07 A 07
Assemble the desktop.
07
or
or
07
M-D M-D
B 07
08
or Philips
Drill
Screwdriver
(not included) (not included)
M-D or
09 07
Secure the desktop panels with the connectors. Then attach the hooks and controller to the desktop.
C 07
Place rubber pads on the desktop screw holes.
or Philips
Drill
Screwdriver
(not included) (not included)
or
M-G
Attach the frame to the desktop.
Step 5 Connecting the Cables
10 09
10 09
11
Step 6 Installing the Cable Hole Covers
12
Using the Controller
Raise the Desk
Press the v button to raise the desk continuously until it reaches the highest
position or the button is released.
Lower the Desk
Press the v button to lower the desk continuously until it reaches the lowest
position or the button is released.
Select Height Setting 1
Press the 1 button, and the desk will move to the height that was previously
set for that button.
Select Height Setting 2
Press the 2 button, and the desk will move to the height that was previously
set for that button.
Select Height Setting 3
Press the 3 button, and the desk will move to the height that was previously
set for that button.
Save Current Height Setting
Short-press the S button, and the screen will show. `S-‘ Press the 1 , 2 , or
3 button to save the current height setting to that button. When you press
the 1 , 2 , or 3 button, the desk will move to the height that was previously
set for that button. Any button-press will stop the desk.
Settings
Reset
Press and hold the v button until ‘rst’ is displayed. Continue holding until
the desk goes down to its lowest level and comes back up slightly. Release the
button, and reset is complete. If the button is released during the reset
procedure, reset will stop. The desk won’t work until reset is done correctly.
Child Lock
Press and hold the v and v buttons together for 5 seconds to turn child lock
on. The screen will show ‘LOC’ and the buttons will be disabled. Turn child
lock off the same way.
Settings Menu
Press and hold the S button for 5 seconds to enter the settings menu. Short-
press the S button to navigate through the menu. Short-press the v or v button
to adjust the settings. Long-press the v or v button to quickly adjust the
height settings. Press and hold the S button again to save the changes. ‘SUS’
will be displayed if saving is successful (or ‘FAL’ if saving fails). If there
is no button-press for 10 seconds, the settings menu will be exited
automatically.
Power-Saving Mode
The screen will turn off if there is no button-press for a minute. Any button-
press will turn the screen on again.
SC0 SC1 SC4 hot r-6 rst
Protection Mode Error Codes
Standby Overvoltage Protection: Standby voltage too high. Power off the desk,
check the connection between power and the controller, and power on again. If
error code persists, please contact technical support.
Power Supply Overvoltage Protection: Input voltage too high. If the correct AC
adapter is being used, power off the desk, check the connection between power
and the controller, and power on again. If error code persists, please contact
technical support.
Operating Overvoltage Protection: Operating voltage too high. Power off the
desk, check the connection between power and the controller, and power on
again. If error code persists, please contact technical support.
Overheating Protection: When the motor has been working continuously for too
long, it will stop operating to prevent overheating. Wait for at least 18
minutes (until error code disappears) before making any further height
adjustment.
Power Supply Overvoltage Protection (during use): Input voltage too high.
Error clears when power supply voltage returns to normal. If error code
persists, please contact technical support.
Reset Warning: Continue to complete reset.
E10
Short Circuit Protection: Power off, check the cable connections, and power back on again. If error persists, please contact technical support.
E11
Overloading Protection: Max load exceeded. Error code will persist for 20 seconds (DO NOT operate). Take the things off the desk and confirm there is no mechanical damage before trying again.
E12
Motor Phase Error Protection: Power off, check the cable connection between the motor and the controller, and power back on again. Then follow the reset instructions. If error code persists, please contact technical support.
E13 E14
Sensor Malfunction Warning: Motor sensor can’t be detected. Power off, check
the cable connection between the motor and the controller, and power back on
again. Then follow the reset instructions. If error code persists, please
contact technical support.
Anti-Collision System Warning: Impact detected. The desk will move 2″ (50mm)
in the opposite direction and stop.
E16
Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected. If error code persists, please contact technical support.
E17
Mechanical Failure Warning: Check if there is any structural damage or motor fault.
Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.