thermaltake TF3 1550W Toughpower Instructions

thermaltake TF3 1550W Toughpower Instructions

Warnings and Caution

1. Do not unplug the AC power cord when the power supply is in use. Doing so may cause damage to your components.
2. Do not place the power supply in high humidity and /or temperature environment.
3. High voltages exist in the power supply. Do not open the power supply case unless you are an authorized service technician or electrician. Doing so will void the warranty.
4. The power supply should be powered by the source indicated on the rating label.
5. Make sure all cables are plugged in properly. Loos and improper connections would damage the power supply and your system.
6. Please use only genuine Thermaltake modular cables with Thermaltake power supply models. Third-party cables might not be compatible and could cause serious damage to your system and power supply. The warranty is voided with the use of third-party cables.
7. All warranties and guarantees will be voided, if failure to comply with any\ of the warnings and cautions covered in this label

Components Check

• TOUGHPOWER TF3 power supply unit
• AC power cord
• User manual
• Mounting screws x 4
• Cable straps x 4

Power Connector Introduction

**|
|
|
|
| **| |
---|---|---|---|---|---|---|---
Main Power Connector (24 Pin)| CPU Connector (8 Pin / 4+4 Pin)| SATA Connector (5 Pin)| PCI-E Connector ( 6+2 Pin)| PCIe Connector (12+4 Pin)| Peripheral Connector (4 Pin)| Extra jumper accessory| Floppy Adapter (4 Pin)
1| 2| 16| 9| 2| 8| 1| 1

Output Specification

Continuous Power| AC INPUT| Input Voltage: 100 – 240V~ ; Input Current: 15.0A ; Frequency: 50 – 60H
---|---|---
1550W| DC OUTPUT| +3.3V| +5V| +12V| -12V| +5VSB
Max Output Current| 22.0A| 22.0A|  129.16A| 0.5A| 3.0A
Max Output Power| 120W| 1549.92W| 1549.92W| 15W

Installation Steps

Note : Make sure that your system is turned off and unplugged. Disconnect the AC power cord from your old power supply

1. Open your computer chassis; please refer to the instruction manual provided with your chassis.
2. Install the PSU into the case with the four screws provided.
3. If your motherboard requires a 24pin Main Power connector, please connect the 24pin Main Power connector to the motherboard.
4. For motherboard that only requires a 4pin ATX 12V (CPU) connector, please detach a 4pin connector from the 4+4pin ATX 12V connector and connect it to the motherboard. (Either one of the 4pin from the 4+4pin ATX 12V connector will work)
5. For motherboard that requires a single 8pin EPS connector, please use the 4+4pin connector from the power supply.
6. Connect other peripheral power connectors to devices such as hard drives,optical drives,etc.
7. Connect the 6+2pin or 12+4pin PCI-E power connector to the PCI-E graphics cards if required.
8. Close your computer case and connect the AC power cord to the power supply AC inlet.
9. This PSU is equipped with a turbo mode button, press this button, the fan speed is the turbo mode.

Total Protection

– Over Voltage Protection

– Under Voltage Protection

– Over Current Protection

EMI & SAFETY

EMI Regulatory & SAFETY Standards
CTÜVus, ICES, CB, CCC, CE, UKCA, LVD, TÜV and FCC certified

Environments

Trouble-Shooting

If the power supply fails to function properly, please follow the troubleshooting guide before application
for service:

1. Is the power cord plugged properly into electrical outlet and into the power supply AC inlet?
2. Please make sure the I/O switch on the power supply is switched to I position.
3. Please make sure all power connectors are properly connected to all the devices.
4. If connected to a UPS unit, is the UPS on and plugged in?

If the power supply is still unable to function properly after following the above instruction, please contact your local store or Tt branch office for after sales service. You may also refer to Thermaltake’s website for more technical support : thermaltake.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>