amazon basics B09JWQH8XG Low Profile TV Wall Mount Instruction Manual
- June 14, 2024
- amazon basics
Table of Contents
amazon Basics B09JWQH8XG Low Profile TV Wall Mount
Tools Needed
- Voltage detector
- Stud finder
Delivery Content
ASSEMBLY INSTRUCTIONS
Pre-Assemble Wall Brackets
- Connect the wall bracket (WP) with the wall bracket with the link plate (WP-2) by tightening the screws (P).
-
Drywall with wooden studs or wooden wall:
Drywall should have a maximum 0.63″ (16 mm) thickness, wood stud size at least 1.5 x 3.5″ (39 x 89 mm). Start drywall installation from 03. Concrete/masonry wall: Concrete wall should have at least 8″ (203 mm) thickness, size of each concrete block is at least 7.99 x 7.99 x 15.98″ (203 x 203 x 406 mm). Start concrete installation from 73. If the wall does not meet the above specifications, do not install the product, contact a professional for assistance.
-
Locate a wood stud with stud finder:
Use a stud finder to locate a wood stud. Mark the two sides of the stud to find the middle point of the stud. The studs must be capable of supporting 4 times the combined weight of the product and the TV.
-
Place drilling template:
Select the desired installation height and tape the drilling template (IT) on the wall aligning it with the stud marking. Check that the TV Center Line (2) on the template is at eye level to the location where you would be sitting. Place a spirit level on the Check Level line (1) of the drilling template (IT) to ensure that it is in a straight line.
-
Drill holes:
Drill 3″ (76 mm) deep holes through the 4 locations (A, B, C, and D) as marked on the template (IT) using a 1/4″ (6.5 mm) drill bit. Remove the drilling template (IT) after drilling.
-
Attach TV mount assembly: One adult holds the TV mount assembly. The second adult half-way tightens the brackets into each of the holes using the fasteners (A) and washers (B). Using a spirit level, check that the TV mount assembly is aligned vertically then fully tighten the fasteners. After this step, proceed to €11.
-
Select installation position: Select a suitable mounting position. Do not drill into any pipes or power lines beneath the surface during mounting hole preparation. Use a voltage/metal detector before drilling any holes to eliminate any such potential risks. The concrete wall must be capable of supporting 4 times the combined weight of the product and the TV.
-
Place drilling template:
Select the desired installation height and tape the drilling template (IT) on the wall. Check that the TV Center Line (2) on the template is at eye level to the location where you would be sitting. Place a spirit level on the Check Level line (1) of the drilling template (IT) to ensure that it is in a straight line.
-
Drill holes : Drill 3.75″ (95 mm) deep holes through the 4 locations (A, B, C and D) as marked on the template (IT) using a 3/8″ (9.5 mm) drill bit. Remove the drillina temolate /IT| after drilling Insert the wall oluas (C) into the drilled holes
-
Attach TV mount assembly: One adult holds the TV mount assembly. The second adult half-way tightens the brackets into each of the holes using the fasteners (A) and washers (B). Using a spirit level, check that the TV mount assembly is aligned vertically then fully tighten the fasteners.
-
Identify mounting pattern
-
To accommodate various TV models, the product comes with screws with different diameters and lengths. It may take a few tries to find the correct screw diameter and length for the TV. The thread on the screw should fit the thread insert on the back of the TV without being too short (unable to hold the TV) or too long (damaging the TV). To avoid damaging the TV, do not force the screws if they do not fit.
-
To accommodate various TV models, the product comes with spacers with different diameters and thicknesses. Take into account that the inner diameter of the spacer should match the fastener used. The spacer type is determined by TV’s enclosure type and its mounting holes.
1. Flat TVs with no obstructions: do not need spacers
2. TVs with inset mounting holes, (3) TVs with cable sockets protruding outwards, (4) TVs with curved backs: need spacers to provide enough clearing for the mounting plate-
Flat or curved TV
-
Install spacers (Brackets with flat TV):
Test the depth and diameter of the TV’s mounting holes using screws D, G and I (sizes M4, M6, and M8). Do not force any of the screws in. If there is resistance, stop immediately and try a screw with a smaller diameter. Find the suitable screws (D/G/I) and pair it with the corresponding washers (L/M). Do a test fit of all 4 holes before fully fastening the brackets to the TV. Proceed to 017).
-
Install spacers (Brackets with curved TV):
The goal of this step is to level the back of the curved TV into a flat surface. Test the depth and diameter of TV’s mounting holes using screws E, F, H, J and K (sizes M4, M6 and M8). Do not force any of the screws in. If there is resistance, stop immediately and try a screw with a smaller diameter. Then test the suitable screw with the corresponding washers (L/M) and spacers (0 or 0/N) to find the suitable combination. Do a test fit of all 4 holes before fully fastening the brackets to the TV. Proceed to 617.
-
Mount the TV to the wall plate: With 1 adult on either side of the TV, lift up the TV to hook the brackets (MA) onto the wall plate. Pull the strings of the brackets downwards, slowly release the TV and then the strings.
-
Loosen/tighten the 2 screws on the brackets (MA) to level the TV.
**Important Safety Instructions
**
Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included. When using the product, basic safety precautions should always be followed to reduce the risk of injury including the following:
CAUTION: Risk of injury and/or property damage!
- Do not exceed the maximum weight indicated. This wall mount is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in the collapse of the wall mount and the attached TV, causing possible injury and/or property damage.
- The product is suitable only for TVs with VESA hole patterns.
< 150 lbs (68 kg) The product is intended for TVs up to 150 lbs (68 kg) of weight and display size of 32″ – 86″ (81.3 – 218 cm). If your TV weighs more, this wall mount is NOT compatible.
- This product is for indoor private household use only and therefore should not be used in public places like restaurants or hotels.
- Be cautious when opening/closing (folding/unfolding) the product. Keep hands away from the folding mechanisms to prevent fingers from being trapped and pinched.
- Keep children and pets away while installing the product. This product contains small parts that could be a choking hazard if swallowed.
- Do not use this product if any parts are missing, damaged, or worn.
- Do not over-tighten the fasteners.
- Regularly examine the product for wear and tear. Stop using the product at first sign of damage or if parts become detached.
- Always support the TV with your hands when making adjustments. Make sure to tighten fasteners and other connections well, but do not over-tighten them.
- Never use an electric power tool to tighten fasteners.
- Strings of the brackets must be out of reach of children and pets. Do not cut, but hide away the strings after installation.
Installation
For additional illustrated mounting/assembly/installation steps, refer to the end of the written instructions. This product should be installed only by 2 adults. If in doubt, consult a professional.
- Refer to the instruction manual provided with the TV you are going to install on this product. It includes additional information for mounting, ventilation and suitable mounting locations. Compare the technical data and requirements to make sure that this product is suitable for the TV.
- Before mounting, determine the suitable mounting location. The product must be fixed to a wooden or masonry/concrete wall using fasteners that are appropriate for the mounting surface. Do not install on drywalls, wall boards or thin plywood. The mounting surface must be capable of supporting at least 4 times the weight of the product and the TV.
- The maximum wall covering thickness, such as gypsum drywall, lath, plastic, etc. should not be greater than 0.63″ (16 mm) for wood stud walls or 0.4″ (10 mm) for masonry walls.
- For wood stud walls: This product is designed to be mounted to 2″ x 4″ (51 mm x 102 mm) and Grade No. 2 wood studs that are spaced 16″ (406 mm) to 24″ (609 mm) on center. Wood studs should be 2″ x 4″ (51 mm x 102 mm), at minimum: 1.5″ x 3.5″ (38 mm x 89 mm).
- For concrete walls: The bracket must be installed into a solid concrete wall. Make sure the concrete wall is suited for Standard Test Method for Compression Strength of Cylindrical Concrete Specimens, ASTM C39, or equivalent.
- Do not drill into any pipes or power lines beneath the surface during mounting holes preparation. Use voltage/metal detector before drilling any holes to eliminate any such potential risks.
- Do not modify the structure of this product in any way.
- If the product is to be attached to any structure other than that specified in this user manual, only a licensed professional contractor/installer should perform this installation. The mounting surface must support, at minimum, 4 times the combined weight of the mounting bracket and the TV. It is the responsibility and liability of the installer to ensure the suitability of the supporting structure.
- Never install it onto furniture! This can lead to instability resulting in personal injuries and/or property damage.
NOTICE
The product is made to fit various TVs with different dimensions. Not all
fasteners delivered are needed for the installation of the product.
Before Assembly
DANGER : Risk of suffocation!
Keep any packaging materials away from children and pets – these materials are
a potential source of danger, e.g. suffocation.
- Remove all the packing materials.
- Remove and review all components before starting assembly.
- Check the product for transport damages.
Disposal
Dispose of the product according to local regulations. If in doubt, consult your local authorities.
Specification
- Display size: 32″ – 86″ (81.3 – 218 cm)
- Max. load: 150 lbs (68 kg)
- Mounting pattern:
- 7.87″ x 3.94″ (200 x 100 mm)
- 7.87″ x 7.87″ (200 x 200 mm)
- 11.8″ x 7.87″ (300 x 200 mm)
- 11.8″ x 11.8″ (300 x 300 mm)
- 15.7″ x 7.9″ (400 x 200 mm)
- 15.7″ x 11.8″ (400 x 300 mm)
- 15.7″ x 15.7″ (400 x 400 mm)
- 23.6″ x 15.7″ (600 x 400 mm)
- Profile: 1.3″ (33 mm)
- Net weight: 6.03 lbs (2.74 kg)
- Product dimensions (W xH x D): 28.76″ X 16.53″ X 1.3″ (73.06 x 42 x 3.3 cm)
Feedback and Help
We would love to hear your feedback. To ensure we are providing the best
customer experience possible, please consider writing a customer review.
Scan the QR Code below with your phone camera or QR reader:
US:
UK : amazon.co.uk/review/review-your- purchases#
If you need help with your Amazon Basics product, please use the website or number below.
US : amazon.com/gp/help/customer/contact-
us
UK : amazon.co.uk/gp/help/customer/contact-
us
+1 877-485-0385 (US Phone Number)
Scan the QR Code and scroll through the images to find an assembly or how-to video
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>