Panasonic EH-NA65 Moisture Infusion Nanoe Hair Dryer Instruction Manual
- June 14, 2024
- Panasonic
Table of Contents
- Safety precautions
- IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
- **** WARNING
- **** WARNING
- **** CAUTION
- OPERATING INSTRUCTIONS
- Parts identification
- How to use the hair dryer
- Troubleshooting
- Specifications
- USER MAINTENANCE INSTRUCTIONS
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
**Panasonic EH-NA65 Moisture Infusion Nanoe Hair Dryer Instruction Manual
**
Safety precautions
To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to equipment or property, always observe the following safety precautions
Explanation of symbols
The following symbols are used to classify and describe the level of
hazard, injury, and property damage caused when the denotation is disregarded
and improper use is performed.
DANGER
Denotes a potential hazard that will result in serious injury or death.
WARNING
Denotes a potential hazard that could result in serious injury or death
CAUTION
Denotes a hazard that could result in minor injury
The following symbols are used to classify and describe the type of instructions to be observed.
This symbol is used to alert users to a specific operating procedure that must not be performed.
This symbol is used to alert users to a specific operating procedure that must be followed in order to operate the unit safely.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
KEEP AWAY FROM WATER
DANGER
As with most electrical appliances, electrical parts are \electrically live
even when the switch is off.
To reduce the risk of death by electric shock:
- Always “unplug” it immediately after using.
- Do not use while bathing.
- Do not place or store this appliance where it can fall or be pulled into a tub or sink.
- Do not place in or drop into water or other liquid.
- If an appliance falls into water, “unplug it” immediately. Do not reach into the water.
WARNING
To reduce the risk of burns, electrocution, fire, or injury to persons:
- An appliance should never be left unattended when plugged in.
- Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities
- Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been damaged or dropped into water. Return the appliance to a service center for examination and repair.
- Keep the cord away from heated surfaces. Do not wrap the cord around the appliance.
- Never block the air openings of the appliance or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
- Never use while sleeping.
- Never drop or insert any object into any opening.
- Do not use outdoors or operate where aerosol(spray) products are being used or where oxygen is being administered.
- Do not use an extension cord with this appliance.
- Do not direct hot air toward eyes or other heat sensitive areas.
- Attachments may be hot during use. Allow them to cool before handling.
- Do not place appliance on any surface while it is operating.
- While using the appliance, keep your hair away from the air inlets.
- Do not use with voltage converter.
- Do not use in countries with 220/240 volt electrical systems- use only with 120 volt electrical systems.
SAVE THESE INSTRUCTIONS
**** WARNING
-
Do not store within the reach of children or infants.
Do not let them use it. -
Doing so may cause burn, electric shock, or injury.
Never modify, disassemble, or repair. -
Doing so may cause ignition or injury due to abnormal operation. Contact an authorized service center for repair.
Do not damage or modify, or forcefully bend, pull, or twist the cord.
Also, do not place anything heavy on or pinch the cord. -
Doing so may cause electric shock or fire due to a short circuit.
Do not use with the cord bundled. -
Doing so may cause fire or electric shock.
Do not wrap the cord tightly around the main body when storing. -
Doing so may cause the wire in the cord to break with the load, and may cause electric shock or fire due to a short circuit.
**** WARNING
Do not use when the power plug or cord is damagedor hot.
-
Doing so may cause burn, electric shock, or fire due to a short circuit.
Never use the appliance if the power plug fits loosely in a household outlet. -
Doing so may cause burn, electric shock, or fire due to a short circuit.
Do not connect or disconnect the power plug to a household outlet with a wet hand. -
Doing so may cause electric shock or injury.
Do not use the appliance with a wet hand. -
Doing so may cause electric shock or fire due to a short circuit.
Do not leave the area with the main switch left on. -
Doing so may cause fire.
Do not store the appliance in a bathroom or location with high humidity. Also, do not place in a location where water may spill (such as top of a vanity). -
Doing so may cause electric shock or fire.
Do not block, or insert hair pins or other foreign objects into the air inlet, air outlet, or nanoe™ outlet. -
Doing so may cause fire, electric shock, or burn.
Do not use in proximity of flammable materials (such as alcohol, benzine, thinner, spray, hair care product, nail polish remover). -
Doing so may cause an explosion or fire
-
Do not immerse the appliance in water.
Do not use this hair dryer near water.
Do not use this hair dryer near bathtubs, showers, basins or other vessels containing water. -
Doing so may cause electric shock or fire.
This symbol on the hair dryer means “Do not use this hair dryer near
water”.
Immediately stop using and remove the power plug if there is an abnormality or
failure.
-
Failure to do so may cause fire, electric shock, or injury.
< Abnormality or failure cases > -
Air is not emitted
-
Unit stops sporadically
-
Interior becomes red hot and smoke is emitted
-
Immediately request inspection or repair at an authorized service center.
Use the household outlet alone: do not use with an extension cord. – Failure to do so may cause fire or electric shock.
Fully insert the power plug. -
Failure to do so may cause fire or electric shock.
Always ensure the appliance is operated on an electric power source matched to the rated voltage indicated on the appliance. -
Failure to do so may cause fire, electric shock, or burn.
-
When you see sparks around the air outlet while using the hot air setting, stop use and remove the lint on the air outlet and air inlet.
-
Failure to do so may cause burn or fire.
Always turn OFF the main switch and disconnect the power plug from the household outlet after use. -
Failure to do so may cause fire or burn.
Disconnect the power plug by holding onto it instead of pulling on the cord. -
Failure to do so may cause the wire in the cord to break, and may cause burn, electric shock, or fire due to a short circuit.
Regularly clean the power plug to prevent dust from accumulating. -
Failure to do so may cause fire due to insulation failure caused by humidity.
Disconnect the power plug and wipe with a dry cloth.
When the hair dryer is used in a bathroom, unplug it after use since the proximity of water presents a hazard even when the hair dryer is switched off. -
Failure to do so may cause an accident or injury.
For additional protection, the installation of a residual current device (RCD) having a rated residual operating current not exceeding 30 mA is advisable in the electrical circuit supplying the bathroom. A sk your installer for advice. -
Failure to do so may cause an accident or injury.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. -
Failure to do so may cause an accident or injury.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard. -
Failure to do so may cause an accident or injury
**** CAUTION
Do not store the cord in a twisted state.
-
Doing so may cause the wire in the cord to break with the load, and may cause electric shock or fire due to a short circuit.
Do not drop or subject to shock. -
Doing so may cause electric shock or ignition.
Do not use with the air inlet damaged. -
Your hair may get dangled in the air inlet, which could damage the hair.
Do not touch the air outlet, set nozzle, quick‑dry nozzle, and diffuser, which will become very hot. -
Doing so may cause burn.
Do not use on children or infants. -
Doing so may cause burn
Never use the hair dryer with the filter removed. -
Your hair may get dangled in the air inlet, which could damage the hair.
Do not wash the filter in water. -
Doing so may cause fire or electric shock.
Be careful about where you point the hair dryer, and be sure to keep your hair at least 10 cm (4˝) away from the air inlet. -
Your hair may get dangled in the air inlet, which could damage the hair.
Please keep a distance of over 3 cm (1˝) between the air outlet and your hair. -
Failure to do so may result in your hair being burned.
Only use for drying or styling human hair. (Do not use on pets, or to dry clothing, shoes, etc.) -
Failure to do so may cause fire or burn
OPERATING INSTRUCTIONS
This product is intended for household use only.
This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug cannot be inserted fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
This appliance is also provided with an ALCI protective device that may make the appliance inoperable under some abnormal conditions (such as immersion of the appliance). If the appliance becomes inoperable, return the appliance to a service center for examination and repair. Every time using the appliance, check the safety plug to verify it is in proper working order. Plug the appliance in an electrical outlet and press the test button. The hair dryer should stop immediately. To resume operation, press the reset button.
This hair dryer is equipped with an automatic overheating protective device. If the hair dryer overheats, it will switch to cool air mode. Switch off the hair dryer and unplug it from the household outlet. Allow it to cool down for a few minutes before using it again. Check that no fluff, hair etc. is in the air inlets and outlets before switching it on again. The thermostat will automatically reset.
Parts identification
A Air outlet
B Set nozzle
C nanoe™ outlet
D nanoe™ lamp
E Cool‑shot button
F Handle
G Ring for hanging
H Cord
I Power plug
J Temperature selector
HOT: Hot air
WARM: Warm air
COOL: Cool air
K Main switch
HIGH: Strong airflow
LOW: Gentle airflow
OFF: Off
L Air inlet
M nanoe™ charge panel
N Quick‑dry nozzle
O Diffuser
-
Set nozzle
For precise styling -
Quick‑dry nozzle
For drying hair quickly
Attach the quick‑dry nozzle so this air outlet is vertical. -
Diffuser
For creating full-bodied hair with lots of volume and styling
How to use the hair dryer
Always check that the filter is securely attached before using.
- Select the temperature of the airflow with the temperature selector (J).
- Select the intensity of the airflow with the main switch (K).
Notes
- The air remains cool while the cool-shot button is held down.
- nanoe™ is produced when the main switch (K) is set to position “LOW” to “HIGH”.
- nanoe™ is invisible to the naked eye.
- If you are worried about hair damage, set the switch to “LOW: Set (Gentle airflow)” before use.
- Drops of water may blow out of the nanoe™ outlet (C) during use, but this is not a malfunction.
- A humming noise may come out of the nanoe™ outlet (C), but this is the sound of nanoe™ being discharged and is not a malfunction.
- The effects of nanoe™ might not be felt by the following people. People with crimpy hair, strong curly hair, very smooth hair, short hair, or who have had a hair straightening perm in the last three or four months.
- You may notice a characteristic odor when using this hair dryer. This is not harmful to the human body
About nanoe™
What is nanoe™?
(nanoe™ generation method: High-voltage discharge) nanoe™ is charged fine
water particles, generated by applying high voltage in order to split water.
Its diameter is smaller than 1/100 of steam, and it cannot be seen with the
naked eye. Since nanoe™ is generated by collecting water in the air, it may be
difficult to generate in certain cases depending on the environment.
(It is harder to collect water in the air when it is cold and humidity is low.)
How nanoe™ works
Generally hair has properties which make it easy to become positively
charged with electricity. These properties attract strongly negatively charged
nanoe™ which penetrates the hair with moisture. Furthermore, they make the
hair slightly acidic, tighten cuticles and keep your hair strong, elastic and
healthy
nanoe™ charge panel
When nanoe™ continues to strike hair, hair becomes negatively charged. As a
result, the nanoe™ and negatively charged hair repel each other, making it
difficult for nanoe™ to reach hair.
With the nanoe™ Charge System, by just gripping the panel together with the handle, the negative charge accumulated on hair is released.
Because of this, nanoe™ continues to penetrate into hair, supplying moisture and thoroughly moistening down to the tips of hair
Maintenance of the hair dryer
- Make sure to turn OFF the main switch and disconnect the power plug from the household outlet. (Except when performing maintenance on the air outlet)
Maintaining the hair dryer
Clean the housing only with a soft cloth slightly dampened with tap water or
soapy tap water.
Notes
- Do not use thinner, benzine, alcohol or other chemicals.
- Doing so may cause malfunction, cracking/discoloration of parts etc.
- Leaving the hair dryer with hair products or makeup still adhered to the handle or body may degrade the plastic, causing discoloration or cracking, and malfunction.
Maintaining the nanoe™ outlet
- Use commercially available cotton swabs. (We recommend the thin cotton swabs made for use with babies.)
- This maintenance allows the hair dryer to sustain the generated level of nanoe™ over a long period.
- Dampen the end of the cotton swab with tap water.
- A needle portion is located deep within the nanoe™ outlet. Using the swab, rub this portion gently about 5 times.
Maintaining the filter
-
At least once a month, when dust etc. has built up, detach the filter from the hair dryer and remove the dust etc. using a toothbrush or vacuum cleaner.
-
Use a commercially available toothbrush.
-
Pull on the catch on the bottom side of the filter to detach
-
Remove any dust etc. adhered to the filter or air inlet.
- Remove the dust etc. adhered to the outside of the filter using a vacuum cleaner. If this does not remove the dust, use the thick part of your fingers to push the dust etc. through the fine mesh on the internal side towards the metal mesh on the external side, and scrub away carefully with a toothbrush.
- Using the toothbrush, carefully scrub away any dust etc. from the internal side of the filter.
- Using a vacuum cleaner or toothbrush, carefully remove any dust etc. adhered to the air inlet.
- Rubbing forcefully with your nails may tear the filter, so please use a toothbrush.
- Attach the filter securely, starting with the upper side.
- Keep pressing until you hear a “click” from both upper and lower catches.
-
Maintaining the air outlet
- The hair dryer should be plugged into the household outlet only in case of maintenance for the air outlet.
- Use a commercially available toothbrush.
- Switch the temperature selector to “Cool” and blow away the dust etc. as you scrub with the toothbrush.
- During maintenance, do not block the air inlet with your hands etc.
- Be careful when using the hair dryer for the first time after maintenance, since it may blow out dust etc.
Scrub to remove any dust, hair etc. blocking the mesh.
Troubleshooting
Problem | Possible cause | Action |
---|
It switches frequently to cold air while using in “Hot” mode, or sparks can be
seen within the body
(These sparks are caused by the thermostat switch, the protective device, and
this is not a malfunction.)| Lint has accumulated on the air inlet or air
outlet
Hair or something is blocking the air inlet| Remove accumulated lint. Do not
block the air inlet
The hot air is abnormally hot
The power plug is abnormally hot.| The connection to the household outlet is
loose| Remove accumulated lint. Do not block the air inlet
Sparks are generated inside the nanoe™ outlet
The nanoe™ outlet emits a noise (crackling noise).| Abnormality caused by a
dirty electrode (needle portion)| Remove accumulated lint. Do not block the
air inlet outlet
If the problems still cannot be solved, contact the store where you purchased the unit or a service center authorized by Panasonic for repair
Specifications
Product name | Hair Dryer |
---|---|
Product model | EH‑NA65 |
Power source | 125 V 60 Hz |
Power consumption | 1875 W |
Accessories | Set nozzle, quick‑dry nozzle, diffuser |
This product is intended for household use only.
This message about…
- G ROUND
- F AULT
- C IRCUIT
- I NTERRUPTERS
*fYOU MUST USEYOUR HAIR DRYER IN THE BATHROOM, INSTALL A GFCI NOW!**
Your local electrician can help you decide which type is best for you- a
portable unit that plugs into the electrical outlet or a permanent unit
installed by your electrician. The National Electrical Code now requires
GFCI’s in the bathrooms, garages, and outdoor outlets of all new homes.
WHY DO YOU NEED A GFCI?
Electricity and water don’t mix. If your hair dryer falls in water while it’s
plugged in, the electric shock can kill you…even if the switch is “off”. A
regular fuse or circuit breaker won’t protect you under these circumstances. A
GFCI offers you far greater protection
A GFCI can save your life! Compared to that, the price is small!! Don’t
wait …install one now!
*GFCI is a sensitive device which reacts immediately to a small electric current leak by stopping the electricity flow
USER MAINTENANCE INSTRUCTIONS
This hair dryer is virtually maintenance free. No lubrication is needed. For proper operating performance, the hair dryer must be kept clean. When cleaning is needed, unplug the cord, and clean dust and lint from air intake openings with a small brush or the brush attachment of a vacuum cleaner. The outer surface of the hair dryer should be wiped clean with a damp cloth only.
This hair dryer should be stored out of reach of children.
Warning – To prevent the risk of electric shock, personal injury or fire, observe the following
- Do not perform any servicing. This hair dryer has no user-serviceable parts.
- Never allow the power supply cord to be pulled, twisted, or severely bent.
- Never wrap the cord tightly around the hair dryer. Damage will occur at the high flex point of entry into the hair dryer, causing it to rupture and short. Inspect the cord frequently for damage. Stop use immediately if damage is visible or unit stops or operates intermittently
FOR YOUR CONVENIENCE, WE HAVE ESTABLISHED A TOLL‑FREE (IN USA ONLY)
NATIONAL ACCESSORY PURCHASE HOT LINE AT
1-800-332-5368.
IN CANADA, CONTACT PANASONIC CANADA INC. AT THE ADDRESS OR TELEPHONE NUMBER ON THE BACK PAGE.
IN USA CONTACT:
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102
-5490
IN CANADA CONTACT: AU CANADA, COMMUNIQUEZ AVEC:
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
(905) 624 -5010
EN MEXICO CONTACTE CON:
Panasonic de México S.A. de C.V.
Félix Cuevas No. 6 Piso 2 y 3
Col. Tlacoquemecatl Del Valle
Del. Benito Juárez
México, D.F. C.P.03200
01 (55) 5488 -1000
EN PANAMA CONTACTE CON:
Panasonic Latin America. S.A.
P.O. Box 0816
-03164
Panama, Republic of Panama
(507) 229 -2955
-
Service
-
Assistance
-
Accessories
Dépannage
-
Assistance
-
Accessoires
Call 1-800-338-0552 (In USA)
http://www.panasonic.com/shavers/
http://www.panasonic.com/consumersupport/
Call 1-800-561-5505 (In Canada)
Composer le 1-800-561-5505 (Au Canada)
http://www.panasonic.ca/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>