EVOLUX EA-9000 WiFi LED Dimmable Smart Light Bulbs Smart Bulb User Guide
- June 14, 2024
- EVOLUX
Table of Contents
EVOLUX EA-9000 WiFi LED Dimmable Smart Light Bulbs Smart Bulb User Guide
PLEASE READ THIS INSTALLATION GUIDE BEFORE OPERATING YOUR PRODUCT
This appliance is not intended for use by persons (including children) whose
physical, sensory or mental capacities are different or reduced, or lack of
experience or knowledge.
Children should be supervised to ensure that they do not use the devices as
toys.
The operation of this device is subject to two conditions:
- This lamp may not cause harmful interference.
- This lamp must accept any interference, including interference that may be caused by undesired operation.
Safety instructions
Read and follow all safety instructions:
- The lamp is not waterproof. Avoid exposing it to splashing or dripping water.
- The operating temperature should be within -10 °C to 40 °C (14 °F to 104 °F).
- The lamp’s internal light source is unfixable. If it breaks, replace the entire lamp.
- Do not install the lamp with a dimming driver.
- Avoid installing the lamp near heat sources.
- Avoid installing the lamp near potentially dangerous sources (e.g., candles, liquid-filled objects).
Introduction
Control your Wi-Fi LED lamp with voice commands and explore a universe of
colors that will brighten your life.
Contents
Color LED Lamp
Quick guide
Diagram
Installation
Installing steps:
- Before installing the lamp, ensure to turn off the switch of the socket or the lamp holder.
- Screw the lamp into the socket, and turn on the switch or the lamp holder. The device will begin to flash.
- If the lamp does not flash, refer to the “troubleshooting” section to restore the lamp to
its factory default settings.
Pairing the device with the Amazon Alexa App
What´s needed:
A Wi-Fi router supporting the 2.4 GHz and 802.11 b/g/n bands. 5 GHz is not
supported.
A smartphone or tablet running iOS 8.0 (or above) or Android 4.3 (or above).
-
Download the Amazon Alexa app from the App Store (iOS device) or Google Play (Android devices).
-
Connect your smartphone to your home network, and ensure the smartphone’s Bluetooth is already on.
-
The lamp will rapidly flash (cold light, 6500K, 10% brightness, 2 times per second) when turning on the power supply. If the lamp does not flash, refer to the “troubleshooting” section to restore the lamp to factory default settings.
Attention: Please complete the pairing process within 5 minutes of powering on the device. -
Open the App and click Devices . + Select and then click Add Device.
-
Select Light -> Evolux, then select your corresponding device, and follow the onscreen instructions to complete pairing. If prompted by the App, scan the 2D barcode on the last page of this guide.
How to create lamps groups
Group multiple lamps to turn them on with a single voice command via Alexa. A group, for example, might include all the lights in the bedroom or the lights in the living room. Follow these steps to create a group:
- Click Devices .
- Select the lamp, then click Add group.
- Enter a name for your group or choose an option from the list. Select Next.
- Choose the lights you want to add to the group and click Save.
- Once set up, all you have to do is tell Alexa which group of lights you want to control. For example, say: “Alexa, turn on the living room.”
How to detect the lamp in the Amazon Alexa App
- Ask Alexa to discover your voice. Say, “Alexa, discover my devices.”
- Alexa will start to discover devices; this may take up a few seconds.
- When Alexa finds your devices, the device name will show on the device list.
Use of the device with Alexa
To use your device with Alexa, say, “Alexa, turn on the lamp.”
Technical specifications
Voltage: 120 VAC 60 Hz
Wattage: 9 W
Color rendering index (CRI): 80
Power factor: 0.5
Luminous Flux: 806 lm
Color: RGB CCT
Color temperature: 2 700 – 6 500 K
Lifespan: 25 000 hours
Base socket: E26
Operating temperature: -10 °C to 40 °C (14 °F to 104 °F).
Relative humidity: 80%
Wi-Fi frequency: 2.4 GHz
Wi-Fi protocol: IEEE 802.11b/g/n
Dimensions (W x H x D): 60 mm x 60 mm x 116 mm
Troubleshooting
-
Can´t connect the lamp to Amazon Alexa.
a. Verify that the Wi-Fi function of your smartphone is enabled.
Ensure you connect to a 2.4 GHz band (the 5 GHz band is not supported).
b. Ensure that the distance between the lamp and the modem is less than 50 ft or within the modem’s network coverage.
c. Check that the lamp enters configuration mode by verifying that it is blinking.
d. Make sure that the Bluetooth function on your smartphone is enabled. -
The lamp lost connection.
a. Check if the device is on.
b. Check that your home network is stable.
c. Go to Devices in the Amazon Alexa App and remove the lamp. Then reconnect it to the Wi-Fi network, following the on-screen instructions to complete the pairing. -
Is it possible to control groups with voice commands?
a. It is possible to group-control lamps with voice commands by creating a group from the Amazon Alexa App. -
Where can I find the barcode?
a. Find the barcode on the last page of this guide. -
What should I do if I do not have a barcode or the configuration has failed?
If you do not have a barcode or the configuration has failed, perform the following steps:
a. Select DON’T HAVE A BARCODE?
b. Turn on the device until the light starts flashing rapidly.
c. Press NEXT to continue with the configuration. -
How to restore to factory default settings?
a. Start with turning off the lamp for at least 5 seconds.
b. Immediately turn it on for 2 seconds, then turn it off.
c. Immediately turn it on again for 2 seconds, and then turn it off.
d. Then turn on the lamp and wait for 5 seconds. If the reset was successful, the lamp will start to blink (6 500 K, 10% brightness, 1 minute later go to 100% brightness).
FCC and ISED Canada Statement
This device complies with Part 15 of the FCC Rules and Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment on and off, the user is encouraged to try to correct the
interference by one or more of the following measures:
a. Reorient or relocate the receiving antenna.
b. Increase the separation between the equipment and receiver.
c. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
d. Consult the dealer or an experienced radio/TV technician for help.
FCC and IC Radiation Exposure Statement
This equipment complies with FCC and IC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 cm between the radiator & your body.
CAUTION This class B digital apparatus complies with CAN ICES-005(B).
Warranty
This product is warranted to last 1 year. If this product does not last the
stated warranty period, please contact us at
support@lloydscorp.com
This product is not guaranteed against wear or breakage due to misuse and/or
abuse.
IMPORTED INTO CANADA BY:
FUNZIONALE HOME INNOVATIONS
Tax ID: 765289665
M113-300 GREEN BANK RD, NEPEAN, ON K2H 0B6 evolux.tech
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>