K NNER S HNEN KS JSP-1200 Jump Starter Owner’s Manual
- June 14, 2024
- K nner S hnen
Table of Contents
- KONNER S HNEN KS JSP-1200 Jump Starter
- Product Information
- Product Usage Instructions
- INTRODUCTION
- JUMP STARTER WITH AIR COMPRESSOR
- MAIN OVERVIEW
- TECHNICAL SPECIFICATION
- FUNCTIONS/OPERATION
- AIR COMPRESSOR FUNCTION
- EC Declaration of Conformity
- CONTACTS
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
KONNER S HNEN KS JSP-1200 Jump Starter
Product Information
Specifications
- Model: KS JSP-1200
- Battery: 14000 mAh
- Max. pneumatic pressure: Not specified
- USB output: Not specified
- USB input: Not specified
- Rated starting current: Not specified
- Peak current: Not specified
- Charging time: Not specified
- Net dimensions (LWH): Not specified
- Net weight: Not specified
- Operating temperature: Not specified
Product Usage Instructions
LED Emergency Lighting
To use the LED emergency lighting:
- Press and hold the key for 3 seconds to turn on the flashlight.
- The light button function changes from solid light to flashing SOS distress signal light.
- Press and hold again for three seconds to turn off the flashlight.
How to Start a Car with a Flat Battery
WARNING! The device is suitable only for 12V0 batteries! When starting the car, please confirm that the power of the product is more than 20%.
- Open the silicone stopper of the product and insert the battery clamp into the corresponding hole of the product.
- Connect the battery clamp to the positive and negative poles of the car battery (Red for the positive terminal and black for the negative terminal).
- Start the engine. Do not cycle the jump starter for more than 3 seconds, pause for 1 minute between jump start attempts. This is necessary to ensure safety and prevent damage to the jump starter.
FAQ
-
Q: What is the maximum pneumatic pressure of the product?
A: The maximum pneumatic pressure is not specified in the user manual. -
Q: What are the USB output and input specifications?
A: The user manual does not provide specific details about the USB output and input specifications.
Please, read this manual carefully before use!
INTRODUCTION
Thank you for your purchase of Könner & Söhnen® products. This manual contains
a brief description of safety, use and debugging. More information can be
found on the official manufacturer’s website in the support section: konner-
sohnen.com/manuals
You can also go to the support section and download the manual by scanning the
QR code, or on the website of the official importer of Könner & Söhnen®
products: www.konner-sohnen.com (for Europe),
uk.koenner-soehnen.com (for the UK), www
.konner-sohnen.com/en-us (for the USA).
Manufacturer reserves the right to make alterations into the generators, which
may not be reflected in this manual. Pictures and photos of the product may
vary from its actual appearance. At the end of this manual,
You may find contact information which you are free to use in case of any
issues occurrence. All data, specified in this operation manual is the most up
to date for the moment of its publishing. The current list of service centers
you can find at the website of official importer: www.konner-
sohnen.com (for Europe), www.konner-sohnen.com
/en-us (for the USA).
ATTENTION
- Failure to follow the recommendations marked with this sign may lead to serious injury of the operator or third parties.
- Useful information while operating the machine.
JUMP STARTER WITH AIR COMPRESSOR
Jump starter has following functions
Jump starter KS JSP-1200 can instantly start 12V vehicles up to 8.0-Liter petrol or 4.0-Liter diesel engines. To avoid safety risks, please do not jump start the car with an unsuitable low capacity.
MAIN OVERVIEW
- Air hose connector
- Air compressor switch
- Pressure down
- Mode selection
- Pressure up
- Intelligent digital display
- DC connector/Output for connecting the terminals of the jump starter
- Power switch
- Charging port
- USB outputs
- Smart clamp
- USB charging cable
- Nozzle adapters+Accessories storage bag
- Air hose
THE PACKAGE INCLUDES:
- Jump starter
- Packaging
- Operating instruction
IMPORTANT!
Manufacturer reserves the right to make changes and/or improvements in design, components set and technical attributes without notice and without incurring obligation. The pictures in this manual are schematical and may not match the parameters of original product
TECHNICAL SPECIFICATION
Model KS JSP-1200 parameters | Value |
---|---|
Battery | 14000 mAh |
Max. pneumatic pressure | 150 psi |
USB output | 2x5V/2А |
USB input | 5V/2А |
Rated starting current | 600 A |
Peak current | 1200 A |
Charging time | 4-5 hours |
Net dimensions (LхWхH) | 200×130×52 mm |
Net weight | 1.45 kg |
Operating temperature | (-20 °C) – (+60 °C) |
FUNCTIONS/OPERATION
HOW TO USE LED EMERGENCY LIGHTING
Press and hold the key for 3 seconds to turn on the flashlight, then the light
button function changes from solid light to flashing, SOS distress signal
light. Press and hold again for three seconds to turn off the flashlight.
HOW TO START A CAR WITH A FLAT BATTERY
When starting the car, please confirm that the power of the product is more than 20%.
- STEP 1: Open the silicone stopper of the product and insert the battery clamp into the corresponding hole of the product
- STEP 2: Сonnect the battery clamp to the positive and negative poles of the car battery (Red for the positive terminal and black for the negative terminal).
- STEP 3: Start the engine. Do not cycle the jump starter for more than 3 seconds, pause for 1 minute between jump-start attempts. This is necessary to let the jump starter battery cool down
- STEP 4: The plug is withdrawn from the jump starter first, and then the battery clips are removed from the positive and negative terminals.
When the connection is successful, the indicator lights up green. The red light indicates that the supply voltage is too low or that the positive and negative electrode terminals have been swapped.
DEVICE CHARGING FUNCTION:
- Plug the USB charging cable into the product 5V/2A USB interface. Plug the other end of the charging cable into the corresponding interface of the mobile phone or digital product. After connecting the cable, press the SWITCH key (device switch) to start power supply.
- The device is protected against overheating. If the device gets overheated, the red indicator light will be on continuously, and the buzzer will emit 2 beeps per second. Once the fault has been rectified, the buzzer will return to normal status. Overtemperature protection is is triggered at 80 °C.
- The device features protection against overcurrent. If the protection is triggered, the device will automatically shut down, the protection indicator will light up, and the buzzer will emit 4 beeps per second. After the fault has been rectified, the indicator will immediately return to normal status.
- It is recommended that you use an AC adapter with an output of at least 5V/1A or preferably 5V/2A for charging. It can be a smartphone or tablet charger.
- Insert the matching adapter and charger plug into the USB Type-C input port of the product
AIR COMPRESSOR FUNCTION
- Connect one end of the inflation line to the air hole
- Connect one end of the inflation cable to the tire
- After connecting the wires, press the key to start the machine
- Then press the M key to select the mode (cars, motorcycles, bicycles, sports equipment).
- Turn on the inflation switch to inflate and automatically stops when the desired parameters are reached
WARNING
- Read the operating instructions carefully before using the device.
- The device must never be used as a substitute for a car battery.
- Keep children and animals away from the working area of the device.
- Only use the jump starter for 12 V batteries.
- Keep the clips and their connection points clean and tidy. Never connect the clips together.
- Avoid using the device near explosive substances, flammable gases, or in dusty environments.
- Avoid overheating the device, smoking near the device, and exposing the device to extreme moisture; keep the device away from open flames and never immerse it in water.
- The device must not be stored at temperatures exceeding 60 °C.
- After successfully jump-starting the vehicle, disconnect the jump starter from the battery within 30 seconds to prevent equipment damage.
- Do not use the jump starter cable to charge other devices.
- Keep it supervised while charging.
- Using the device at current and voltage ranges other than those specified on the device nameplate may cause charging and discharging problems and deterioration of battery capacity and performance. This is also dangerous and may cause the device to malfunction.
- When the battery is stored for more than three months, the product needs to be charged to ensure the normal performance of the product
- Never do anything that may cause mechanical damage to the device.
- Do not disassemble or transform the product without authorization.
- If the device casing is bulged, leaking, or giving off an unpleasant odor, stop using the device immediately.
- If you notice battery acid leaking from the battery, do not touch it with bare hands. If battery acid contacts the skin or eyes, rinse immediately with plenty of running cold water and soap. Flush eyes for at least 10 minutes. Seek medical advice if necessary.
- The device features a lithium rechargeable battery that must be disposed of under the applicable laws in your country.
- Please connect the starting cable correctly according to the manual.
- Never attempt to jump-start the vehicle in continuous mode! With standard power, the start cycle should take no more than 3 seconds, and the interval between cycles should be at least 1 minute. Do not exceed 3 consecutive start attempts.
- After starting the car with the starting power, the temperature of the starting power supply itself will rise, please do not charge the starting power at this time, at least 8-10 minutes before charging.
- Only use the jump starter cable supplied with the jump starter.
- Do not charge the device immediately after jump-starting the vehicle’s battery.
- Never use the device to start the vehicle’s battery and charge the device’s internal battery simultaneously
EC Declaration of Conformity
The following products have been tested by us with the listed standards and found in compliance with the European Community Electromagnetic compatibility Directive (EMC) 2014/30/EC.
- Manufacturer: DIMAX INTERNATIONAL GmbH
- Address: Flinger Broich 203, 40235 Duesseldorf, Germany
- Product: Jump starter with air comprssor “Kanner & Sohnen”
- Type / Model:
The statement is based on a single evaluation of above mentioned products. It does not imply an assessment of the whole production and does not permit the use of the test lab. logo. The manufacturer should ensure that all product in series production are in conformity with the product sample detalied in this report. The applicant should hold the whole technical report at disposal of the competent all the right.
- Applied EC Directives:
- 2014/30/EU Electromagnetic compatibility Directive (EMC) EU Ro HS 11 /65/EU 2015/863/EU
- Applied Standard
- IEC 61000-6-3:2021
- EN IEG..6 000-6-1 :2019
- EN IEC 61000-3-2:2019+ A 1 :2021
- EN–6 000- 3:2013+A 1 :2019
Issued Date:
Place of issue: 2023-08-10
General director: Fomin P.
We DIMAX INTERNATIONAL GmbH hereby declare that specified above conforms
covering European Parliament and Council Directives, Electromagnetic
compatibility Directive (EMC) 2014/30/EC of 26 February 2014. The CE mark
above can be used under the responsibility of manufacturer. After completion
of an EC declaration of Conformity and compliance with all relevant EC
directives.
CONTACTS
Deutschland:
DIMAX International GmbH Flinger Broich 203 -FortunaPark- 40235
Düsseldorf, Deutschland
www.koenner-soehnen.com
Ihre Bestellungen
orders@dimaxgroup.de
Kundendienst, technische Fragen und Unterstützung
support@dimaxgroup.de
Garantie, Reparatur und Service
service@dimaxgroup.de
Sonstiges
info@dimaxgroup.de
The United Kingdom: Innovation Trade Ltd., 63/66 Hatton Garden Fifth Floor,
Suite 23, London, EC1N 8LE
info.uk@dimaxgroup.de
Technical support
support.uk@dimaxgroup.de
Polska:
DIMAX International Poland Sp.z o.o. Polska, Warczawska, 306B 05-082 Stare
Babice,
info.pl@dimaxgroup.de
www.konner-sohnen.com
Україна:
ТОВ «Техно Трейд КС», вул. Електротехнічна 47, 02222, м. Київ, Україна
sales@ks-power.com.ua
www.konner-sohnen.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>