Revolo RE002 Keyless Entry Door Lock Instruction Manual

June 14, 2024
Revolo

Revolo logo

RE002 Keyless Entry Door Lock

Revolo RE002 Keyless Entry Door Lock

Programming Instructions

Information and Safety Warnings

  • Failure to follow these instructions could result in damage to the product and void the factory warranty.
  • The accuracy of the door preparation is critical for the proper functioning and security of this product. Misalignment can cause performance degradation and lessening of security.
  • This lockset is designed to provide the highest standard of product quality and performance . Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners, or polishes could damage the coating and result in tarnishing.

NOTE: Do not load batteries until lock is completely installed.)

  1. Master PIN Code (4~10 digits): The default master pin code is “12345678”, It’s required that you change it to a code of your own before programming.
  2. User PIN Code (4~10 digits): A total of 30 user codes may be programmed.
  3. Neither master nor user PIN codes support the following combination of numbers.

Revolo RE002 Keyless Entry Door Lock - Fig 1

Parts Illustrations

ITEM SPECIFICATIONS REMARKS
Exterior Assembly  155.2mm(L)x70.5mm(W)x30.6mm(H)
Interior Assembly 153.2mm(L)x68.3mm(W)x57.2mm(H)
Battery AA alkaline battery x4 Last up to eight months (10 times open/close

per day)

Revolo RE002 Keyless Entry Door Lock - Fig 2

CAUTION: Master and User PIN code have 4~10 digits, the default master PIN code is{12345678}.Please change it prior to programming of the lock)

Definitions

Master Code:
Required for programming and feature settings. Master code can be used to unlock the door under vacation mode. The default master code needs to be changed before programming.(Property owner/ manager should keep this information confidential.)

Auto Unlock:
Automatically locks the deadbolt 30 seconds after unlocking. This feature is disabled by default.

Wrong Entry Limit:
After 10 unsuccessful attempts at entering a valid PIN code, the unit will shut down for 3 minutes.

Silent Mode:
The beep sounds when pressing keypad can be muted. But you will still hear low battery and system alerts.

Vacation Mode:
This is a security feature for you when you are leaving your home for vacation or long trip. Enabling vacation mode will restrict all user codes until master code is entered on keypad. If the lock is unlocked by thumbturn or the key, the lock will sound an alarm.

Unlock with Fake Code:
User can prevent PIN code from exposure by entering random digits before or after PIN code.

Privacy Mode:
When the privacy mode is activated, the door cannot be opened from outside except with master PIN code.

Factory Default Settings

SETTINGS FACTORY DEFAUIT
Master code 12345678
Auto lock Disabled
Silent mode Disabled
Wrong code entry limit 10 times
Shutdown time 3 minutes

Restore factory default settings

  1. Keep your lock in “unlock” status, insert 4AA batteries in battery pack.
  2. Use the provided reset pin to press and hold the reset button for more than 5 seconds until hearing beep sound.
  3. If reset is successful, the bolt will extend on its own to learn the orientation of the door.

Troubleshooting

  • The lock can’t be locked or unlocked by keypad?
    Make sure the codes are not disabled. If needed, restore the lock to default settings.

  • The keypad doesn’t respond when touched (no lights and no beeps)?
    Make sure the power cable is properly connected. Change the batteries with 4 brand-new AA standard alkaline batteries. Do not mix old and new batteries.

  • The REVOLO logo on top of the keypad keeps flashing red?
    It indicates the battery life is under 20% and please change the batteries as soon as possible.

  • Forgot the Master or user PIN codes
    Perform a reset to erase all passcodes. Once the reset is complete, all passcodes will be erased, and the master code will return to the default. (12345678).

How to use?

Unlock the door from outside

Lock the door from outside

Enable Auto-lock
When this feature is enabled, the lock will automatically relock itself 30 sec after being unlocked.

Revolo RE002 Keyless Entry Door Lock - Fig 5

Lock Operation

The default master code is 12345678. It’s required that you change it to a code of your own before programming.
When setting is unsuccessful, the indicator light will flash red.

Revolo RE002 Keyless Entry Door Lock - Fig 6

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals