Winsen RPFA913CG Pyroelectric Flame Sensor User Manual
- June 14, 2024
- Winsen
Table of Contents
Winsen RPFA913CG Pyroelectric Flame Sensor
Statement
This manual copyright belongs to Zhengzhou Winsen Electronics Technology Co.,
LTD. Without the written permission, any part of this manual shall not be
copied, translated, stored in database or retrieval system, also can’t spread
through electronic, copying, record ways.
Thanks for purchasing our product. In order to let customers use it better and
reduce the faults caused by misuse, please read the manual carefully and
operate it correctly in accordance with the instructions. If users disobey the
terms or remove, disassemble, change the components inside of the sensor, we
shall not be responsible for the loss.
The specific such as color, appearance, sizes &etc, please in kind prevail.
We are devoting ourselves to products development and technical innovation, so
we reserve the right to improve the products without notice. Please confirm it
is the valid version before using this manual. At the same time, users’
comments on optimized using way are welcome.
Please keep the manual properly, in order to get help if you have questions
during the usage in the future.
Zhengzhou Winsen Electronics Technology CO., LTD.
RPFA913CG Pyro-electric Flame sensor
RPFA913CG pyro-electric flame sensor uses lithium tantalate single crystal as the sensitive element material. The Curie temperature of lithium tantalate crystal material is above 600℃, the relative dielectric constant is small, and the specific detectivity is high.
In a wide range of room temperature, the pyroelectric coefficient of the
material changes very little with temperature, and the temperature change rate
of the output signal is only 1-2‰. The temperature stability of the sensor
performance is very good, and the spectral response consistency is very good
in the wavelength range of 1-20um.
Features
- 5.0um detection band;
- TO-5 package, single channel, voltage mode;
- Low microphone effect, large FOV, high detection rate;
- Detection band measurement of flame signal
Applications
It’s widely used in various oil storage stations, large warehouses, factory
workshops, forests, charging piles; and standard configuration for high fire
risk areas such as petroleum, chemical, paper-making, forests, and garages.
It also becomes popular in high-end residential, commercial, and general
industrial fields.
DIMENSIONS
Size (Unit : mm)
Parameters
Table 1
| Item | Typical | Unit |
|---|---|---|
| Window Size | 5.0*5.0 | mm |
| Sensitive element size | 3*3 | mm |
| Filter center wavelength | 5.0 | um |
| Electrical time constant | 5 | s |
| Thermal time constant | 200 | ms |
| Source Voltage | 0.4~0.7 | v |
| Working Voltage | 2~15 | v |
| Recommended voltage | 3~5 | v |
| Output signal V0 (500K,10HZ,25℃) | 4.3±10% | v |
| Output noise voltage VN (10HZ, BW1HZ, 25℃) | ≤150 | mv |
| Voltage response rate (no window) Rv (500K, 10HZ, 25°C) | ≥500 | v/w |
Specific detection rate (no window) D*
(500K, 10HZ, BW1HZ, 25℃)| ≥5×108| cmHz½/W
Field of view(FOV)| >115| °
Detection distance| >35| m
Working temperature/ Storage temperature| -40~+85| ℃
Remarks: The magnification of the testing machine is 80dB.
Internal circuit
Sensor 1 pin Vd is the drain of the field effect transistor, and voltage is
applied; pin 2 Vs is the output signal; pin 3 GND is grounded.
Lithium tantalate sheet and a high resistance Rg form a parallel circuit, and
then connect to the gate of the field effect transistor.
Testing circuit
Application circuit
Filter parameters
5.0um narrow band filter spectral curve
Filter parameters of commonly used sensor models
Part No.| RPFA913CC| RPFA913CD| RPFA913CE| RPFA913CF|
RPFA913CG
---|---|---|---|---|---
Center wavelength (nm)| 3800±40| 4300±50| 4400±40| 4480±40| 5000±40
Full width at half maximum FWHM (nm)| 180±20| 600±40| 400±20| 620±20| 180±20
Transmittance (%)| ＞90%| ＞90%| ＞90%| ＞85%| ＞90%
Notes:
- Pyroelectric infrared sensors are piezoelectric and are very sensitive to sound, electromagnetic waves and vibration. When using pyroelectric infrared sensors, proper shock absorption and shielding are necessary.
- In order to avoid turbulent air flow and crosstalk, which may cause false alarms, when the sensor is used in the design of the flame detector, window protection (such as white sapphire, calcium fluoride or infrared glass, etc.) must be added.
- When welding the pyroelectric infrared sensor, it is recommended to solder at a position above 3mm. When using a soldering iron for manual soldering, the temperature of the soldering iron tip should be controlled below 350℃, and the soldering time for each location is less than 3 seconds, and the tube should be clamped with tweezers, to prevent damage to the electronic components under high temperature conditions.
- During the installation and use of the pyroelectric infrared sensor, prevent the sensor components from falling. The sensor should be stored in a dry environment.
- When operating the pyroelectric infrared sensor, the temperature of the pyroelectric infrared sensor is changed due to hand contact, especially through welding. Therefore, when the sensor is working again, it is necessary to wait for a period of time. After the temperature of the sensor is balanced, resume normal work.
- Do not touch the sensor window directly with your hands and hard objects. Keep the window clean. When there is dirt, use an alcohol cotton ball to gently wipe it clean.
- When installing the sensor, it is forbidden to apply mechanical pressure to prevent damage to the sensor’s sensitive elements, windows and other components due to the existence of pressure.
- When the sensor is taken out from the packaging box, and during measuring and installing, it must be equipped with electrostatic protection tools. The electrostatic protection requirement is less than 2000V to prevent the high voltage from breaking down the field effect tube of the sensor.
Note: To keep continual product development, we reserve the right to change
design features without prior notice. Zhengzhou Winsen Electronics
Technology Co., Ltd
Add: No.299, Jinsuo Road, National Hi-Tech Zone, Zhengzhou 450001 China
Tel: +86-371-67169097/67169670
Fax: +86-371-60932988
E-mail: sales@winsensor.com
Website: www.winsen-sensor.com
Tel: 86-371-67169097/67169670
Fax: 86-371-60932988
Email: sales@winsensor.com
References
- Winsen Gas Sensor_CO2 Sensor_Air Quality Sensor_Dust Sensor_CO Sensor-Winsen Electronics
- Winsen Gas Sensor_CO2 Sensor_Air Quality Sensor_Dust Sensor_CO Sensor-Winsen Electronics
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>