NGTECO NG-PPS500 Portable Power Station User Manual

: June 14, 2024
: NGTeco

**NGTECO NG-PPS500 Portable Power Station User Manual

**

Important Notes

Please read the following instructions to ensure safety before using.

Improper use may cause fire, property damage or personal injury

Product use

DO NOT use any inappropriate power cords.
DO NOT place the unit close to or in a fire on expose it to heat. Keep out of direct sunlight.
DO NOT charge, use or store the unit in a bathroom or in an area exposed to rain or moisture. Do not drop the unit into the water.
If the battery in the unit comes into contact with water, it may cause chemical decomposition of the battery. This may cause the battery to catch fire or explode.
- Never use or charge swollen, leaky, or damaged batteries. If your battery is abnormal, contact us to get support.
- Never install or remove a battery from the unit when it is turned on.
DO NOT use the batteries in strong electrostatic or electromagnetic environments. Otherwise, the battery control board may malfunction and cause a serious accident.
- Never disassemble or pierce the product in any way. Otherwise, it may leak, catch on fire, or explode.
DO NOT use the product if it was involved in a crash or a heavy bump.
- If the product falls into the water during use,take the product out immediately and put it in a safe and open area. Keep a safe distance from it until it is completely dry. Never use it again and dispose it properly as described in the Battery Disposal section below. If the product catches fire, it is recommended to use fire extinguishing equipment in the following order: water or water mist, sand, fire blanket, dry powder, carbon dioxide fire extinguisher.
- Do Not allow pins, wires or other metal pieces to insert to the device case, outlets or controls. Metal pieces may short circuit the product.
- Avoid collision. DO NOT place heavy objects on the machine.
- Use and store the unit only in a clean and dry environment. Do not use and store in dusty and wet environment.
  Important Notes
- If there is dirt on any plug or outlet surface, use a dry cloth to clean it. Otherwise, it will cause abrasion and result in energy loss or inability to charge.
DO NOT put the machine in a microwave oven or in a pressurized container.

Product Recharging

DO NOT charge the unit via power supply systems that operate outside of AC100-240V.
DO NOT charge the unit via solar panel that operate voltage outside of DC12-26V.
- Always use approved attachment charging cables, we take no responsibility for any damage caused by using other brand charging cable.
- When charging, please place the product on the ground with no flammable or combustible materials around. To prevent accidents, never leave the machine unattended during charging.
DO NOT charge a product immediately after a long heavy load, because the product’s temperature may be too high. DO NOT charge a product until it cools down to room temperature.
- Only charge, use the unit within an ambient temperature of 0 to 40 °C (32~104°F).
  The ideal charging temperature range is 71°F to 82°F(22°C to 28°C).

Product Storage and Transportation

Keep the product out of the reach of children. If any children accidentally swallow parts, please go to a doctor immediately.
If a low-battery warning appears, charge the battery before store it.
Store the product in dry environments. DO NOT place the product where it may contact with water.
Make sure no small metal objects can fall on or around the product while in storage.
Never transport a product with a battery power level higher than 30%.

Product Maintenance

Never store the product in environments below -20°C or above 45°C.
Battery life may be reduced if not used for a long time.
Fully charge and discharge the battery at least once every 3 months to maintain battery health.

What’s in the Box

Portable Power Station X1
Power Adapter X1
12V Car Anderson cable X1
MC4-Andersor connector cable X1
User Manual X1

Product Overview

Front:

LCD Screen Display
DC 5525 Output
Cigarette Lighter Output
USB-C Output
USB-A Output 1
500W Rated AC Output
Anti-collision Strip
DC Input
PV Input
SOS MODE&LED light
Folding Handle
**Side :

**

Air Intake Vent with Cooling Fan
Wireless Charger.

Note: No user-serviceable parts inside. Recommended to fully charge the NG-PPS500 before use.

The AC Output port may very in different regions.

Button Feature

A: NG-PPS500 Power ON/OFF Button
B: SOS mode & LED light Button
C: DC Output Power ON/OFF Button
D: USB Output Power ON/OFF Button
E: AC Output Power ON/OFF Button

Function Buttons:

Button A : NG-PPS500 POWER ON/OFF Button A is the master switch. Press Button A to turn on the power or to shut down the output(s) when not in use.
Button B : SOS MODE& LED LIGHT Function is available no matter the Button “POWER ON/OFF” is activated or not as the following steps :
Firstly: press Button B to turn on the LED light into the LED light mode.
Secondly: double click it to turn on the SOS mode.
Thirdly: press Button B back to LED light mode .then press it again, the light will be turn off.
Button C : DC OUTPUT POWER ON/OFF
Pls. make sure the button “POWER ON/OFF ” is activated before pressing Button C to turn on : Press Button C to shut down the output(s) when notin use.

Button D : USB OUTPUT POWER ON/OFF Pls. make sure the button “POWER ON/OFF” is activated before pressing Button D to turn on :Press Button D to shut down the output(s) when not in use.

The USB-C cable of different devices need different endorsements of corresponding protocols, if the USB-C port doesn’t work, try to use the AC adapter to charge .

Button E : AC OUTPUT POWER ON/OFF

Pls. make sure the button “POWER ON/OFF” is activated before pressing Button E to turn on ;Press Button E to shut down the output(s) when not in use.

Wireless Charger

Press “POWER ON/OFF” Button to turn on the wireless charger. Press
“POWER ON/OFF Button to shut down the output(s) when not in use.

Cooling Fan

NG-PPS500 utilizes an internal cooling fan to ensure the product is operating within the appropriate temperature range. NG-PPS500,whenit experiences a higher output load, will automatically turn on the fan during discharge or recharging , the fan may operate intermittently to keep internal temperature within operating range. The fan will likely start when the AC circuit is activated to ensure proper operation.

LCD Features

H: Battery Level Indicator
I: Input Status
J: DC Outputs Status
K: AC Outputs Status
L: USB Outputs Status

Details Displayed On LCD

Battery Level Indicator

The battery level is provided by percentage of battery charge corresponding to the number of bars and percentage displayed. The segments in the battery level correspond to the current state of charge, 0-5% empty, 6-20% one segment, 21-40% two segments, 41-60% three segments, 61-80% four segments, and all five are lit when charge level is above 81%.

Provides the user live telemetry data on time to completely charge, or deplete the battery based upon the energy entering or leaving the battery.
Highly recommend to fully charge NG-PPS500 when first use. Higher battery level indicator show, more precise the data will indicate3) Please be aware that this value can adjust multiple times as the energy draw changes from the connected devices. This is evident during initial activation of ports with a connected device.
Recommended to charge the NG-PPS500 when battery indicate less than 20%.
Note that when you first plug in a power source, whether it’s a solar panel or a wall charger, the NG-PPS500 may take a minute to detect and adjust its charge circuitry before it starts drawing power from the source.

INPUT Status : The NG-PPS500 is capable of providing input energy in watts.

DC Output Status : The display will provide output watts of the DC port.

AC Output Status : The display will provide output watts of the AC port. Power-saving mode:

when the device enters the input or output state, it will enter the screen-off mode after more than 20 seconds, which does not affect the normal operation of the device. When the output power of the device is less than 5W, the device will go into hibernation after more than 3 hours, and the input can be “awakened” when the input is charged or any button is pressed. When not in use, press the switch button to turn off the output.

With It Powers

Laptops(41.4Wh) Around 10 Recharges
32″ TV(60W) 7 hours
CPAP without heated humified(15W) 29 hours
Gopro(5.9Wh) Around 74 Recharges
Floodlight(4W) Around 110 hours
Mini Fridge(40W) Around 11 hours
DJ Drone(89.2Wh) Around 4.9 Recharges
Smartphone(10Wh) Around 44 Recharges
Switch(16Wh) Around 27 Recharges

How to charge

From Solar Charger 150W 6-9 hours depending on solar conditions.

From Car Port 12V 9-11 hours when car running

From Wall Charger 220V 7 – 8 hours.

Note : Do not connect device via ac output port while charge the NG- PPS500.recommend to disconnect the NG-PPS500 when fully charged.

AC Adapter Charging

It will take 6-7 hours to charge fully by using the AC adapter we provided.
Adapter Charging

Solar Panel Charging

DO NOT charge the unit via solar panel that operate voltage outside of DC12-26V .
Place Solar Panels in direct sunlight as much as possible.
Support 60W/80W/100W/120W Max Solar Panels (Not included), the charging time is determined by the solar light intensity.

Recommend to use 120W Solar panel (not included).

12V Car Charger Charging

Car Charger Charging

Use the Car Charger we provided to chalge this unit. The full charge time takes 7-8 hours. When the LCD display shows the battery power of 100%, it indicates that this unit is fully charged.

Operating Instructions

Charging NG-PPS500 Connect the provided AC Wall power adapter to Input, and allow NG-PPS500 to fully charge prior to use, approx. 5-7 hours.When charging, the LCD Screen will be illuminated, and the LCD display will provide Battery level Indicator, NG-PPS500 is fully charged when the level is 100%. It is recommended to fully charge NG-PS500 every 3 months to maintain the health of the battery pack.
Powering/Charging Devices With NG-PPS1000 Select the type of outlet required by pressing the Output ON/OFF Button C/D/E. The output port will NOT function until the appropriate button is pressed to activate the port. When activated, the indicator on the button will illuminate green, indicating that the output(s) are active, and the LCD display will turn on and provide details on the charging output. The LCD Screen will automatically shut down when no outputs are activated.
Pass-Through Charging
The advanced battery management system of the NG-PPS500 allows it to charge a connected device via DC output & USB output while charge the NG-PPS500.
DO NOT Connected Device VIA AC Output With Charge the NG-PPS500.
Overload Condition
If an overload condition occurs on the OUTPUT port, NG-PPS500 will:
Automatically turn off AC Output(6)power.
The blue indicator light of LCD Screen(1)still illuminated. DC OUTPUT Status J still the same status as usual. 4)Do Following:
Check the input charge cable. The port will be efficient when the input charge cable meets the specification outlined in the GENERAL SPECIFICATIONS section.
Note: Only charge NG-PPS500 with provided AC wall power adapte

Other Considerations

Cleaning
Be sure that NG-PPS500 is disconnected from all input power sources and output devices. Use a clean, dry, soft-lint-free cloth to wipe down it. Remove any debris, dirt, or other blockages on both side vents. When cleaning debris from the side vents, do not allow the debris, dirt, or other blockages to enter the body of NG-PPS500.
DO NOT use abrasive cleaners or solvents.
DO NOT use compressed airto clean side cooling vents, as this will force foreign particles into the internal circuitry.
To avoid the risk of electrical shock, DO NOT use metal objects to clean ports.
Storage
If storing for more than 1 month, charge completely before storage and recharge approximately every 3 months to avoid full discharge and possible damage. Store indoors, in cool temperatures, mild humidity, and away from direct sunlight (See GENERAL SPECIFICATIONS section). Leaving in a vehicle or other confined spaces in extreme hot. temperatures can lead to decreased service life, overheating, and fire. Extreme cold conditions below specific storage range can also harm PS500 performance and service life. Keep away from corrosion chemicals and gases. After taking out of storage, visually inspect to make sure NG-PPS500 and all accessories look satisfactory. This increase review the intake and exhaust side vents to ensure they are clear of debris. Allow NG-PPS500 to return to ambient conditions before recharging, or charging other devices.
Attention
Transportation: NG-PPS500 complies with all legal requirements for transport of dangerous goods. The capacity of the lithium battery pack exceeds 10OWh.

Based on international standards, if NG-PPS500 is transported by airplane, it must be transported in accordance with IATA standard packaging. IATA instructions and labeling requirements and the relevant declarations must be completed.

Not Permitted On Aircrafts
To Preserve The Battery Lifespans, Please Use And Recharge At Least Once Every 3 Months
Use Original Or Certified Charger And Cables
Avoid Extreme Temperature
Avoid Dropping
Do Not Disassemble
It’s Not Waterproof, do Not Expose To Liquids
Please Dispose Of Batteries And Electronic Goods In Accordance With Local Regulations

Troubleshooting

NG-PPS500 WILL NOT CHARGE OR OPERATE connected devices: Ensure that the DC/USB/AC output ports are activated by pressing the Button(s)

A & C/D/E for the port(s) in use.

Confirm the connected device is suitable for the NG-PPS500 by reviewing the output specifications provided in the GENERAL SPECIFICATIONS section.

Confirm NG-PPS500 is charged by reviewing the Battery Level Indicator H.

Verify the watt data displayed on the Status Indicator l/J/K of LCD

Screen for overload condition.

The device can not be charged:

Confirm that the wall plug power adapter’s cord is inserted fully into the DC Input
Confirm that the AC wall plug power adapter is the charger provided with NG-PPS500.

If the input does not comply with the requirements located in the general specifications section, the low watt range 0 % to 10 %may be displayed on the LCD.

If the device cannot be charged immediately after it is discharged, please wait for an hour and try again, it may enter the over-temperature protection.

Maintenance

Recharge as needed. There are no pre-designated intervals at which to recharge as long as the NG-PPS500 is being used regularly. Avoid discharging completed on a regular basis, as this can impact overall life.

Regularly inspect all ports and wall charger for any debris, dirt, damage and corrosion.

DO NOT attempt to fix.

DO NOT cover the NG-PPS500 with towels, clothing or other items. Regularly observe if the side vents are collecting dirt or dust, and clean following cleaning procedures noted in manual.

Disposal/Recycle

Do not place equipment and its accessories in the trash. Items must be properly disposed of in accordance with local regulations. See www.epa.gov for additional information.

Statement

The information contained herein is subject to change without notice. The only warranties for NGTeco products and services are set forth in the warranty statements accompanying such products and services. Notec shall not be liable for technical or editorial errors or omissions contained herein.

Limited Warranty

We warrant to the original consumer purchaser that our product will be free from defects in workmanship and material under normal consumer use during applicable warranty period identified in the “Warranty Period” section below, subject to the exclusion set forth below. This warranty statement sets forth ours total and exclusive warranty obligation. We will not assume, not authorize any person to assume for us, any other liability in connection with the sale of our products.

Warranty Period

The warranty period is 12 months. In each case, the warranty period is measured starting on the date of purchase by the original consumer purchaser. The sales receipt from the first consumer purchase, or other reasonable documentary proof, is required in order establish the start date of the warranty period.

Remedy

We will repair or replace any our products that fails to operate during the applicable warranty period due to defect in workmanship or material. If a valid claim is made during the applicable period. We, at its option, will either (1) replace the product, or (2) exchange the product with a product that is of equal value. A replacement product assumes the remaining warranty of the original product or ninety (90) days from the date of replacement, whichever is greater. Customer is responsible for the return shipping costs.

Limited To Original Consumer Buyer

The warranty on ours product is limited to the original consumer purchaser and to any subsequent owner.

Exclusions

Our warranty does not apply to (1) any product that is misused, abused, modified, damaged by accident, or used for anything other than normal consumer use as authorized in ours current product literature, or (2) any product purchased through an online auction house.

Ours warranty does not apply to the battery cell unless the battery cell is fully charged by you within 7 days after you purchase the product at least every months thereafter

How To Receive Service

To obtain warranty service, contact our customer service team.

General Specifications

General Specs

Rated capacity: 519.48Wh
Weight (net weight) : 6.8kg
Weight (including accessories): 7.8kg
Product size: 290mm194mm200mm

Input

Recharging input voltage: 12-26V
Recharging input power : 100W
AC/DC Adapter: 100W MAX AC 100-240V (50Hz/60Hz),DC 25V 4A
Solar Charge Input: 12-26V DC 6A MAX
Car Charger: DC 12V, 100W MAX

Output

AC Output Voltage: 230V/50HZ
Rated Output Power: 500W
Output waveform: pure sine wave
Overload protection Power: 550+40W
Cigarette Lighter Socket Output: 14V/8A
DC *552.5 output: 14V/4A
Wireless charger: 10W
U SB output: QC3.0/18W
Output Type-C:** PD60W

Battery

Standard capacity of cells : 3.7V/140400mAh
discharging Temperature: 14 to 104°F (-10 to 40°C)
Recharging Temperature: 32 to 104°F (0 to 40°C)

1600 Union Hill Road Alpharetta, GA 30005
E-mail: service.ng@ngteco.com
www.ngteco.com