tp-link TL-WN881ND 300 Mbps Wireless N PCI Express Adapter User Manual

tp-link TL-WN881ND 300 Mbps Wireless N PCI Express Adapter

INTRODUCTION

How do I install the TP-Link wireless adapter manually on Windows XP?

Note: This article applies to the situation that failed to install the adapter through. the EXE program and the adapter have a .inf file to download. (please download the latest driver from TP-Link official site, and extract the zip file to see whether your adapter has a .inf file.) Before the installation, please make sure the adapter is connected to the computer and is detected by the system.

INSTALLATION INSTRUCTION

Step 1
Click on Start, and go to Run…

Step 2
Input “devmgmt. msc” and click OK.

Step 3
Find the newly detected hardware, right-click it, and then click Update Driver…

Step 4
Select No, not this time.

Step 5
Select Install from a list or specific location (Advanced).

Step 6
Select Don´t search. I will choose the driver to install.

Step 7
Select Show All Devices.

Step 8
Click Have Disk.

Step 9
Click Browse….

Step 10
Point to the inf. file in the driver folder, and then click Open.
Note: Is your computer running the 32-bit or 64-bit version please click Start, right-click My Computer, and then click Properties.

• If “x64 Edition” is listed under System, you’re running the 64-bit version of Windows XP.
• If you don’t see “x64 Edition” listed under System, you’re running the 32-bit version of Windows XP.

The edition of Windows XP you’re running is displayed under System near the top of the window.

Step 11
Click Next.

Step 12
Click Continue Anyway.

Step 13
Click Finish.

As yet, the adapter has been successfully installed. You can go to Device Manager and check Network Adapters.

Why cannot I connect to my wireless network

Case1. The authenticating problem, password mismatch

1. Make sure your password typed is correct. You can refer to this FAQ to find the wireless password: How to find or change the wireless password on the TP-Link products
2. Sometimes it will ask you to type in a PIN number when you connect to the wireless network for the first time. This PIN number is different from the Wireless Password/Network Security Key. Usually, you can only find it on the back panel of your wireless router/modem. If you cannot find the PIN or PIN incorrect, you may choose “Connecting using a security key instead”, and then type in the Network Security Key/Wireless Password.

If it continues on saying network security key mismatches, it is suggested to confirm the wireless password on your wireless router/modem. Please contact your router’s support for help if you don’t know how to confirm the wireless password.

NOTE: Wireless password/Network Security Key is case sensitive.

Case 2. Windows was unable to connect to XXX / Cannot join this network / Taking longer than usual to connect to this network.

There are various causes of this kind of problem:

1. Weak wireless signal. Check the wireless signal strength of your network. If it is weak (1~3 bars), please move closer to the router and try again.
2. Wireless Mac filtering or access control function blocks the specified wireless clients to connect.

Check the wireless settings on the router. Make sure Wireless MAC Filtering or Access Control is NOT enabled.

Too much interference

1. Try to change the wireless Channel of the router to reduce interference from other networks. For example:
   • For the 2.4GHz channel, you can change the channel to 1, 6, or 11 to test.
   • For the 5GHz channel, you can change channels 36, 52, or 149 to test
   • You can refer to this FAQ to change the wireless channel: https://www.tplink.com/en/support/faq/3085/
2. Try to turn off other wireless routers or devices like microwaves/soundbars/Bluetooth

Your wireless clients have some problems.

1. Try to turn off and turn on/reboot your wireless clients to connect to the Wi-Fi.
2. Contact the support of your wireless clients.

Some devices don’t support specified wireless settings like encryption or wireless mode.
You can refer to this FAQ to change the wireless settings: How to Change your Security Settings on your TP-Link Router (new UI)

Suggestion:

1. Change the wireless name and wireless password
2. Change the wireless security encryption
3. Change the channel width
4. Change the wireless mode

Other suggestions.

1. Try to connect via WPS. Press the WPS button on the router and then press the WPS button on the adapter. For more details, you can refer to How to connect to a wireless network while a PIN code is required in Windows 7 (WPS/QSS).
2. Re-install or update the driver for your wireless adapter of the computer. Please contact computer/wireless adapter support for help if you don’t know how to update the driver.
3. Refer to Why cannot I connect to the secured wireless network of the router? for more solutions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>