Walmart EKF 3-Light Bathroom Vanity Light Instruction Manual
- June 14, 2024
- Walmart
Table of Contents
****
Walmart EKF 3-Light Bathroom Vanity Light
Product Information
- Item Number: A05149B
- Maximum Wattage: Type A, Max 60W per bulb
- Voltage: 120V
Specifications
- The mounting surface should be clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides.
- Any gaps between the mounting surface and canopy exceeding 3/16 should be corrected as required.
- The ceiling or wall should be able to support the weight of the lamp before installation.
- The lamp should be kept away from acidic and alkaline substances to prevent damage to the surface.
Product Usage Instructions
WARNING
To reduce the risk of fire, electric shock, or personal injury, please
follow these instructions:
- We suggest installation by a licensed electrician.
- Read the instructions carefully and save it for future reference.
- Before starting any work, always shut off the electricity.
- When replacing bulbs, turn off or unplug the lamp and wait until it is cool as bulbs get hot quickly.
- Use common sense, caution, and care with any electrical products.
Tools Required
Before starting assembly and installation, please prepare the following tools:
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Included
- (C) Mounting plate (1)
- (D) Green ground screw (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Socket (3)
- (H) Lampshade (3)
- (I) Socket ring (3)
Accessories Enclosed
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
Assembly & Installation Instructions
- Carefully remove the fixture from the carton and check that all parts and accessories are included.
- Turn off power before starting the installation.
- Secure mounting plate (C) to the outlet box with mounting screws (A).
- Connect wires as shown in the below wires connection chart.
Note : Never connect other wires to ground wires.
Wires Connection Chart
Connect Black or Red Supply Wire to:
- OUTLET BOX GROUND
Connect White Supply Wire to:
- OUTLET BOX GROUND
- FIXTURE GROUND
Note:
When parallel wires (SPT I& SPT II) are used, the neutral wire is square
shaped or ridged, and the other wire will be round in shape or smooth.
FAQ
-
Q: Can I install the product myself?
A: We suggest installation by a licensed electrician to ensure safety. -
Q: What is the maximum wattage for each bulb?
A: The maximum wattage is Type A, Max 60W per bulb. -
Q: What voltage should I use?
A: The voltage should be 120V.
INSTRUCTION
Item Number :A05149B
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. » Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. » Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture
PARTS INCLUDING
- (C) Mounting plate (1)
- (D) Green ground screw (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Socket (3)
- (H) Lampshade (3)
- (I) Socket ring (3)
ACCESSORIES ENCLOSED
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done. -
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. -
Place the wall switch in the “OFF” position
-
Make assembly
-
Step A1 » Unscrew knob nuts (F) from back plate (E), then set them aside for later installation.
-
Step A2 » Carefully pass the supply wires from the outlet box through the mounting plate (C). Secure mounting plate (C) to the outlet box with mounting screws (A).
-
Step A3 » Make wire connections Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
Twist wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box. -
Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (C) with the previously removed knob nuts (F). Hand tighten until snug.
NOTE : back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (C): -
Unscrew the pre-assembled hex nuts.
-
Screw the pre-assembled mounting screws in or out of the mounting plate (C).
-
When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4
-
Step A5 »
-
Remove socket rings (I) from sockets (G).
-
Carefully place lampshades (H) to sockets (G), and then screw socket rings (I) to sockets (G) to secure them as shown in the illustration.
-
Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
-
Check everything is installed properly, then you can turn on the light. Enjoy
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper
+1 850 296 2377
Working hours: Mon – Fri 9:00 – 16:00 EST
homecustomercare@outlook.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>