HL D-THO-4824JPT Electric Standing Desk with Keyboard Tray Instruction Manual
- June 14, 2024
- Hl
Table of Contents
HL D-THO-4824JPT Electric Standing Desk with Keyboard Tray
Product Information
Specifications:
- Model: (/(&75,& 6,767$1”(6
- Weight: (KGS
- Dimensions: 2KLZ2KM x 8OMNZ2KM x *XOK8UJ
- Power: 9OJK6RGZK
- Color: 2KM(GYK
Product Usage Instructions
Step 1: Assembly
Align the holes of the Left Leg (2) and Drive Rod (4). Use Wrench (M-H) to
secure both with Screw (M-A).
Step 2: Insert Drive Rod
Insert the Drive Rod (4) into the hole in the Right Leg (3). If it is not
possible to insert, please rotate the Right Leg (3) slightly until the inner
hexagon matches.
Step 3: Install Beam
Use Wrench (M-I) to install Beam (1) to the Legs (2 & 3) with Screws
(M-B)*6.
Step 4: Connect Orbitals
Pull out the orbitals completely. Use screwdriver(19), with Screws (M-G)*4,
attach the drawer connector to the track.
Step 5: Attach Keyboard Retainer
Attach the keyboard retainer (132) to the drawer using screwdriver(19) and
Screws (M-D)2.
Step 6: Install Drawer Connector
Install the drawer connector in the middle of the table (7a) using
screwdriver(19) and Screws (M-D)*4.
Step 7: Finalize Installation
Follow the remaining steps in the manual to finalize the installation of
the product.
FAQ
Q: How much does the product weigh?
A: The product weighs (KGS.
Q: What are the dimensions of the product?
A: The dimensions are 2KLZ2KM x 8OMNZ2KM x *XOK8UJ.
Q: What is the power source for the product?
A: The product is powered by 9OJK6RGZK.
Q: What is the color of the product?
A: The color of the product is 2KM(GYK.
@ HJ-Customer-Service@outlook.com
© (909)637-7665 | (909)637-7593
EST 9:00AM–17:00PM
PARTS
INSTALLATION
Please read the installation instructions carefully before installatio
Step 1
Align the holes of Left Leg (2) and Drive Rod (4), Using Wrench (M-H)to secure both with Screw (M-A).
Step 2
Insert the drive rod (4) into the hole in the right leg (3). If it is not
possible to insert, please rotate the right leg (3) slightly until the inner
hexagon matches.
Step 3
As shown, use Wrench (M-I), install Beam (1) to the Legs (2&3) with Screws (M-B)*6
Step 4
Using Wrench(M-l, install Leg Base (6)*2 to the Legs (283) respectively with Screws (M-C)”8.
Step 5
Use screwdriver (19), install Side Plate (5)2 on each side of the Legs (2&3) with Screws (M-F)4.
Step 6
Step 7
Fix Boards (7a&7b) with Wooden Pin (16)4. Use screwdriver(19), with Screws (M-D)10, install Desk Connection Plate (14)3 to the middle of the Boards, and Desk Connection Hook (8)2 to both sides of the Boards.
Step 8
Pull out the orbitals completely ( 11) Use screwdriver (19), with Screws (M-G)*4,Attach the drawer connector to the track
NOTE:
- When installing the keyboard connector, the side of the small hole (threaded) should be facing downwards.
Step 9
Use screwdriver (19), with Screws (M-D)2, Attach the keyboard retainer ( 13 )
2 to the drawer
Use screwdriver(19), with Screws (M-D)*4 , Install the drawer connector in the
middle of the table(7a)
Step 10
Fix Silicone Sheet (18)*10 to the corresponding hole position on the Boards (7a&7b).
Step 11
Use screwdriver(19), secure the Leg part to the Boards (7a&7b) with Screws (M-E)10. Please align the Silicone Sheet (18)10.
Step 12
As shown, connect the motor at the Left Leg (2), Hand Controller (9) and Power Supply (10) in turn.
Step 13
Using screwdriver(19), install Hand Controller (9) to the Board (7a) with Screws (M-D)2. Secure the connecting cable with Cable Clip (17)2 and glue it to the bottom of the Board.
Step 14
Insert Cable Hole Cover (15)*2 into the hole in the Board (7b).
Using the Controller
-
Raise the Desk
Press the button to raise the desk continuously until it reaches the highest position or the button is released. -
Lower the Desk
Press the button to lower the desk continuously until it reaches the lowest position or the button is released. -
Select Height Setting 1
Press the 1 button, and the desk will move to the height that was previously set for that button. -
Select Height Setting 2
Press the 2 button, and the desk will move to the height that was previously set for that button. -
Select Height Setting 3
Press the 3 button, and the desk will move to the height that was previously set for that button.
Save Current Height Setting
Short-press the S button, and the screen will show ‘S-‘ .Press the , 2, or 3
button to save the current height setting to that button. When you press the
1,2, or 3 button, the desk will move to the height that was previously set for
that button. Any button-press will stop the desk.
Settings
-
Reset
Press and hold the button until ‘rst’ is displayed. Continue holding until the desk goes down to its lowest level and comes back up slightly.
Release the button, and reset is complete. If the button is released during the reset procedure, reset will stop. The desk won’t work until reset is done correctly. -
Child Lock
Press and hold the and buttons together for 5 seconds to turn child lock on. The screen will show ‘LOC’ and the buttons will be disabled.
Turn child lock o the same way. -
Settings Menu
Press and hold the S button for 5 seconds to enter the settings menu. Short- press the S button to navigate through the menu.
Short-press the or button to adjust the settings. Long-press the or button to quickly adjust the height settings. Press and hold the S button again to save the changes. ‘SUS’ will be displayed if sor 10 seconds, the Setings menu wil be exit hautomati auton-press -
Power-Saving Mode
Tutor pes i tum it screen on agon press for a minute. Any button press will turn the screen on again.
Protection Mode Error Codes
Technical Support
(909)637-7665 | (909)637-7593
Other Info
HJ-Customer-Service@outlook.com
Thank you for choosing this product. We strive to provide you with the best
quality products and service in the industry. Should you have any issues,
please don’t hesitate to contact us.
https://hlinstallationvideos.s3.amazonaws.com/D-THO-BC-Electric+Sit-
stand+Desk.mp4
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>