HOMECUSTOMER LYIMIRN5169Q9C 3 Light Gold Bathroom Vanity Light Instruction Manual
- June 14, 2024
- HOMECUSTOMER
Table of Contents
HOMECUSTOMER LYIMIRN5169Q9C 3 Light Gold Bathroom Vanity Light
Product Information
Specifications
- Item Number : A05169
- Voltage: 120V
- Maximum Wattage : Type A, Max 60W per bulb
Product Usage Instructions
Tools Required
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Included
- (E) Green ground screw (1)
- (F) Mounting plate (1)
- (G) Back plate (1)
- (H) Stud (2)
- (I) Socket ring (3)
- (J) Glass shade (3)
- (K) Socket (3)
Accessories Included
- (A) Anchor (4)
- (B) Wood screw (2)
- (C) Mounting screw (2)
- (D) Plastic wire connector (3)
Assembly & Installation Instructions
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the provided illustration.
- Turn off power. Before starting the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Make necessary preparations for later installation.
- Drill holes on the wall for anchors (A) using the provided illustration as a guide.
- Connect wires according to the provided wire connection chart. Ensure that the ground wire is only connected to other ground wires.
- Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Make sure no wire strands are exposed and carefully tuck all wires into the outlet box.
- Attach the back plate (G) to the mounting plate (F) using the previously removed studs (H). Hand tighten until snug.
- Place glass shades (J) on sockets (K) and then screw socket rings (I) to secure them.
- Install bulbs (not included) into the sockets. Please do not exceed the maximum recommended wattage.
FAQ
- 1. Do I need a licensed electrician for installation?
- We suggest installation by a licensed electrician to reduce the risk of fire, electric shock, or personal injury.
- Can I install the fixture without turning off the electricity?
- No, before starting any work, you must shut off the electricity until the work is done to ensure safety.
- What should I do if there are gaps between the mounting surface and canopy?
- Any gaps exceeding 3/16 should be corrected as required to ensure a proper and secure installation.
- Can I use bulbs with wattage higher than the recommended maximum?
- No, please do not exceed the maximum wattage recommended on the socket to prevent damage or safety hazards.
- Can I replace bulbs while the lamp is still on?
- No, when replacing bulbs, you should turn off or unplug the lamp and wait until it is cool as bulbs can get hot quickly.
Item Number: A05169
WARNING (To reduce the risk of fire, electric shock, or personal injury)
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools
as below picture
PARTS TYPE & QTY INCLUDING
- (E) Green ground screw (1)
- (F) Mounting plate (1)
- (G) Back plate (1)
- (H) Stud (2)
- (I) Socket ring (3)
- (J) Glass shade (3)
- (K) Socket (3)
ACCESSORIES & QTY ENCLOSED
- (A) Anchor (4)
- (B) Wood screw (2)
- (C) Mounting screw (2)
- (D) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Turn off power
- Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Make installation
- Step A1 » Unscrew studs (H) from back plate (G) then gently remove mounting plate (F). Then set them aside for later installation.
- Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (F).
NOTE: To drill the holes on the wall for anchors (A)
- Attach mounting plate (F) to the outlet box with mounting screws (C) and mark the holes.
- Unscrew mounting screws (C) and remove mounting plate (F), drill holes and gently knock anchors (A) into the holes until anchors (A) are level with the wall.
- Secure mounting plate (F) to the outlet box with mounting screws (C) and wood screws (B).
- Step A3 » Make wire connections
- Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
*Note: When parallel wires (SPT I & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus.)
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Step A4 » Align the holes in back plate (G) with the pre-assembled mounting screws, then attach back plate (G) to mounting plate (F) with the previously removed studs (H). Hand tighten until snug.
Step A5 »
- Unscrew socket rings (I) from sockets (K).
- Place glass shades (J) on sockets (K) and then screw socket rings (I) to secure them.
- Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>