Brookstone B08BTN2LS3 Amphibious RC Car User Manual

Brookstone B08BTN2LS3 Amphibious RC Car User Manual

Driving Tips & Transmitter

Driving Tips:

• Make sure the power switch is turned to ON position for driving,the vehicle will have no functions when turns OFF.
• Open the spout after the car landing from the water to drain the water.

Restart: Press this button to re-frequency alignment after changing the battery.

Battery Installation

1. Open the vehicle’s battery cover.install the battery pack and connect to the vehicle.
2. Open the transmitter’s battery cover, install 2X1.5V”AA” batteries with correct polarity as shown inside the battery compartment.(NOT INCLUDED)
3. Replace the battery cover and tighten screw with a screwdriver.

Battery Installation for Vehicle

Notice: Only use the special charger for battery charging.

Battery Installation for Transmitter

2X1.5V”AA” batteries (NOT INCLUDED)

1. Do not mix new and old dry-cell battery together in use.
2. Do not mix rechargeable battery and dry-cell battery together in use.

Operation Manual of Remote Control

• Forward
  

• Backward
  

• Turn Left
  

• Retreat to the Left
  

• Turn Right
  

• Retreat to the Right
  

• 360° Rotate Left
  

• 360° Rotate Right
  

Bind the transmitter to the receiver: The indicator lights on after the body power is connected.The indicator flashes when the remote controller is connected with power supply and lights go out after the frequency alignment is completed.The indicator lights on when operation.Switch the power OFF on the transmitter and vehicle after use,prevent power from consumption.

BATTERY SAFETY GUIDELINES

1. In order to avoid an accident for the reason of overcharge, do not charge for long periods of time without attention.
2. Use only the USB rechargeable battery pack provided to recharge.
3. Do not disintegrate, alter or dismantle batteries in any way.
4. Do not to use the battery in high temperature areas or near source of easy-burning objects.
5. During charging the battery, maintain ventilation and ensure the charge under safe conditions and avoid potential fire prevention situations.
6. If the battery has one of the following phenomenon of special odor, overheating, color changing, distorting or any abnormal phenomenon during application, storage or power charge, please immediately move the battery out of the toy or the charge to outdoor safe place (don’t litter about the battery with these abnormal characteristics in order to avoid burn and/or explosion of battery.
7. Do not store or transport the battery with metal.
8. Do not place to batteries into fire or heat batteries in any way.
9. Do not use metal to connect the anode and cathode of battery.
10. Do not overturn the anode and cathode of battery.
11. If any battery leakage occurs and comes in contact with skin or eyes do not rub. Use clean, clear water flush and immediately seek medical attention.
12. If batteries from R/C vehicle and remote control are not going to be us ed for long periods of time remove them and keep them in a cool, dry environment.

WARNING:

1. Adult supervision required.
2. Do not attempt to modify the remote control in any way.
3. All the packaging material must be removed by an adult.

CAUTION:

1. Do not mix old and new batteries.
2. The supply terminals are not to be short-circuited.
3. Non-rechargeable batteries are not to be charged.
4. Always remove weak or used or dead batteries from the product.
5. Do not dispose of batteries in fire, batteries may explode or leak.
6. Rechargeable batteries are to be removed from the toy before being charged.
7. Rechargeable batteries are only to be charged under adult supervision.
8. Only batteries of the same or equivalent type as recommended are to be used.
9. Do not mix Alkaline, standard (carbon-zinc), or rechargeable batteries.
10. The toy must be fully assembled in accordance with the instructions before operating.
11. Be sure to insert the batteries correctly and always follow the toy and battery manufacturers’ instructions.

Warning: changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CONNECT & DISCOVER MORE:

HAVE QUESTIONS OR COMMENTS? CALL TOLL FREE:833-811-2042 

RETAIN THE PACKAGING FOR FUTURE REFERENCE. COLORS AND CONTENTS MAY VARY FROM THOSE ILLUSTRATED. THE BROOKSTONE® TRADEMARKS, NAMES AND LOGOS ARE OWNED BY BKST BRAND HOLDINGS, LLC. © 2020. ALL RIGHTS RESERVED. MANUFACTURED. MARKETED AND DISTRIBUTED BY INNOVATIVE BRANDS, LLC UNDER LICENSE.

VEHICLE: 3.7V USB RECHARGEABLE BATTERY (INCLUDED)
REMOTE CONTROL: 2x 1.5V “AA” (NOT INCLUDED)

INNOVATIVE DESIGNS, LLC
132 W. 36TH St, 8TH FLOOR
NEW YORK, NEW YORK 10018
212-695-0892

ITEM NO. 707556BRS
MADE IN CHINA
F12806/20L707556

FCC STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>