HOMECUSTOMER LMEVNAM976PH8C Contemporary Dome Linear LED Mini Indoor Kitchen Island Light Instruction Manual
- June 14, 2024
- HOMECUSTOMER
Table of Contents
HOMECUSTOMER LMEVNAM976PH8C Contemporary Dome Linear LED Mini Indoor
Kitchen Island Light
Product Information
Specifications
- Item Number : A04976P
- Voltage : 120V
- Maximum Wattage : Type B, Max 40W per bulb
Product Usage Instructions
Tools Required
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Included
- (C) Mounting plate (1)
- (D) Green ground screw (1)
- (E) Canopy (1)
- (F) Swivel joint (1)
- (G) Knob nut (2)
- (H) Tube
- (I) Iron frame (1)
- (J) Socket (1)
- (K) Iron shade (1)
- (L) Socket ring (1)
Accessories Included
- (A) Plastic wire connector (3)
- (B) Mounting screw (2)
Assembly & Installation Instructions
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the illustration.
- Before starting the installation, turn off the power. NEVER attempt any work without shutting off the electricity.
- Remove the mounting plate (C).
- Use the tubes (H) and pass the fixture wires through the chosen tubes (H), swivel joint (F), and canopy (E).
- Tighten all the threaded pipes and screw the chosen tubes (H) onto the swivel joint (F) and the top of the iron frame (I). Hand tighten until snug.
- Secure the fixture to the ceiling or wall using the mounting screws (B).
Wiring Instructions
Connect wires as shown in the following charts. NEVER connect other wires
to ground wires.
Ground Wires Connection
Connect ground wires according to the below chart
| A | B |
|---|---|
| OUTLET BOX GROUND | GREEN GROUND SCREW |
| OUTLET BOX GROUND | FIXTURE GROUND |
Wire Connection
Connect black or red supply wire to
| Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
|---|---|
| OUTLET BOX GROUND | GREEN GROUND SCREW |
| OUTLET BOX GROUND | FIXTURE GROUND |
FAQ
- Q: Can I install the fixture myself?
- A: We suggest installation by a licensed electrician to reduce the risk of fire, electric shock, or personal injury.
- Q: What should I do before starting the installation?
- A: Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Q: Can I replace the bulbs while the lamp is still on?
- A: No, when replacing bulbs, you should turn off or unplug the lamp and wait until it is cool as bulbs can get hot quickly.
Item Number: A04976P
WARNING (To reduce the risk of fire, electric shock, or personal injury)
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- » Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- » Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED) : Before starting assembly and installation please prepare the needed tools as below picture
PARTS TYPE & QTY INCLUDING
- (C) Mounting plate (1)
- (D) Green ground screw (1)
- (E) Canopy (1)
- (F) Swivel joint (1)
- (G) Knob nut (2)
- (H) Tube
- (I) Iron frame (1)
- (J) Socket (1)
- (K) Iron shade (1)
- (L) Socket ring (1)
ACCESSORIES & QTY ENCLOSED
- (A) Plastic wire connector (3)
- (B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Turn off power
- Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- » Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- » Place the wall switch in the “OFF” position.
- Unscrew knob nuts (G) from canopy (E).
- Remove mounting plate (C).
- According to your desired hanging height to choose and use tubes (H).
- Then pass the fixture wires through the chosen tubes (H), swivel joint (F) and canopy (E).
- Be sure that all the threaded pipes are tightened, then screw the chosen tubes (H) onto swivel joint (F) and the top of iron frame (I).
- Hand tighten till snug.
- Attach mounting plate (C) to the outlet box with mounting screws (B).
- » Make wire connections
- Connect wires as below wires connection shown. REFER TO THE FOLLOWING CHARTS, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
-
Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
- Twist wires together with plastic wire connector (A) until tightly joined.
- Wrap each connector with approved electrical tape for a more secure connection.
- Carefully tuck all wires into the outlet box.
- Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening knob nuts (G) onto the pre-assembled screws in mounting plate (C).
- Note : canopy (E) should be snug against the ceiling and knob nuts (G).
- If not, adjust the threaded length on mounting plate assembly (C)
- Unscrew the pre-assembled hex nuts.
- Screw the pre-assembled screws in or out of mounting plate (C).
- When the secure length is achieved, tighten the hex nuts and back to step 7.
- Remove socket ring (L) from socket (J).
- Fix iron shade (K) to socket (J) with socket ring (L).
- Install the bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
- Check everything is already installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials
such as scouring pads or powders, steel wool or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>