ecoartheating B07QZRVC8K Temperature Controller Electric Thermostat Instruction Manual
- June 14, 2024
- ecoartheating
Table of Contents
ecoartheating B07QZRVC8K Temperature Controller Electric Thermostat
Function
The external temperature detector can detect the temperature, set the opening temperature and closing temperature, and has the functions of cycle timing, timing opening, timing closing and timing switch. It is widely used in intelligent control such as carbon crystal heating, aquaculture, greenhouse, home life and other places.
Real-time temperature range: -40~120 °C
- Open circuit (Or less than-45°C) The first row of the screen flashes display “E1”, -40~-45°C display-40°C.
- Short circuit (Or more than120°C) The first row of the screen flashes display “E2” 121-129°C display 120°C
- Lower than-10 C Or higher than-100 C It will not display the value behind the decimal point.
- Refrigeration mode, When the setting temperature is higher than the stop temperature, the corresponding icons are displayed .
- Heating mode, When setting the starting temperature below the stop temperature is heating mode, display the corresponding icon .
Four button
MODE button, SET button, UP button, DOWN button.
-
MODE button (MODE):
Press the MODE button LCD DISPLAY: Temperature Control Mode -Timing mode F01~F04
- F01 Cyclic timing Mode, Start time (ON) /Stop time (OFF) Cycle timing.
- F02 Count down On Mode, Now Ti.s OFF, Delayed (Start time) ON.
- F03 Count down Off Mode, Now Ti.s ON, Delayed (Stop time) OFF, Countdown completion, Turn off the output and exit the run.
- F04 Count down On Count down Off Mode, Now Ti.s OFF, Delayed (Start time) ON, After Starting Delayec (Stop time) OFF. Stop the time to finish the countdown. Close out the output and exit the operation.
No opening or closing when the start time/stop time is 0 under the timing mode, Corresponding time scintillation alarm. Run state prohibition of switching timing mode.
Under temperature control mode: or Blinking (It is based on the mode of
heating or heating.)
Under timing mode: Current running mode”ON”/”OFF” Blinking, Time symbol”:
“Blinking, Meanwhile, time is running,
After the start of the machine, Relay suction when running to ON, Socket output indicator light, Relay shutdown at OFF, and Light indicator.
SET Button (SET):
- Temperature mode, Press the setting button, set up the start temperature and stop the temperature The temperature range is -40~120 C (The default starting temperature is 20C, and the stop temperature is 25°C)
- Timing mode (F01-F04) Press the setting button, Set up start hours, minutes/stop hours, minutes, set range of 0~99 hours 59 minutes.
- Running state. Allow temperature/time adjustment by setting the button.
UP Button, DOWN Button
- At the time of the numerical scintillation, A numerical adjustment is made according to UP Button and DOWN Button.
- According to a UP Button or down Button plus / minus 1, the long-time value is automatically added and reduced.
- Under the nonrunning state, At the same time, press UP Button and DOWN Button3 seconds to restore the factory setting
Temperature correction function
- Long press mode button on electricity, Real time temperature calibration after 2 seconds, LCD first row display “CALIBRATION” and Real-time temperature, the Correction value of LCD second row scintillation display, Adjust the correction value according to UP Button and DOWN Button According to the adjusted calibration value, the real-time temperature changes accordingly.)
- Real-time temperature correction range:-9.9~9.9°C.
- Long press the “SET” button or 5 seconds automatically exit, Do not save modification, Long press the “MODE” button to exit. Save the current correction modification.
°C or °F switch:
Press and hold the “SET” button for more than 5 seconds to change °C or F.
Backlight Mode:(This feature is limited to the backlit version)
Connect to AC power, backlight immediately light, if not press any button,
backlight will went off in 10 minutes. When press any of the buttons, the
backlight start light again.
Memory function: All current settings will be saved after power off.
Factory test
Reset the factory settings, press the RESET button, the screen is displayed
for one second, restore the factory settings.
Technical parameters
- EU FR PLUG: 16(2)A 230V~ Max.3680W.u
- UK PLUG: 13(2)A 230V~ Max.2900W.u
- AU PLUG: 10(2)A 240V~ Max.2400W.u
- US PLUG: 15(2)A 120V~ Max.1800W.u
- Temperature range: -40~120°C
- Temperature control accuracy: +1%
- Timing accuracy: MAX 10 minutes
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>