Fairland X30 Ai Wireless Robotic Pool Cleaner User Manual

Fairland X30 Ai Wireless Robotic Pool Cleaner

AI-WIRELESS ROBOTIC POOL CLEANER
USER MANUAL

X30/45/60/80
THANK YOU FOR PURCHASING X30/45/60/80 AI-WIRELESS ROBOTIC POOL CLEANER Please read the manual carefully before
installing or using it and keeping it for subsequent use.

TIPS

How to achieve the most efficient cleaning
Place the robot at the corner of the pool for quick coverage of the entire pool floor area.

How to drain water from the robot
Place the robot on the edge of the pool for a while and let the water drain out.

How to open the filter box

For battery protection, the robot should be fully charged every 3 months and the magnetic cap should be inserted back if the robot is not used for more than 14 days.

• Do not charge the robot outdoors.
• Do not long-term expose the robot to the sun.

WARNINGS
This page contains information that will help you operate the robot safely, prevent hazards and damage to the robot or other property.

GENERAL WARNINGS

• Read the instructions before operating the robot.
• The robot is designed for pool cleaning; do not use it for other purposes.
• Keep the robot out of reach of children or persons with reduced physical, sensory or mental capabilities without supervision or instruction.
• The robot must be installed, operated and maintained as specified in this manual.
• The robot is to be installed in accordance with manufacturer’s guidelines and in compliance with the relevant requirements of the local or national standards for installation. The manufacturer is not responsible for any outcome related to the failure to comply with installation, usage or maintenance guidelines.
• Incorrect installation or use of the robot may cause serious damage to property or injuries to people.
• Do not enter pool while the robot is in water.

WARNINGS ON USE

• Only use the detachable supply unit provided with the robot to recharge the battery. It is suggested to operate the power supply at least 3.5 meters from edge of pool.
• Disconnect the robot from the power supply and insert the magnetic cap back in place before performing any maintenance on the robot.
• Do not operate the robot with wet hands to avoid insensitive touch.
• Do not try to repair the robot yourself or open motor box in case of malfunction, please contact your dealer.
• If there is any malfunction or release of odor from the robot when charging, disconnect it from the power supply immediately and contact your dealer.
• Use only original replacement parts supplied by the manufacturer for service and repair.

GENERAL OPERATION CONDITIONS

Note: water temperature below 15℃, the endurance time may be affected.

• The robot is recommended for private pools.
• The robot will automatically stop running if the water depth is less than 40 centimeters for the purpose of motor protection.
• In pool floor mode, the robot will not climb the wall if the slope exceeds 30°.
• Do not use the robot during shock chlorination.
• Do not use the robot in thunderstorm or stormy weather.
• Do not expose the robot to direct rainfall or sunlight for an extended period.

CAUTIONS

• Hold the robot by the pool edge to let the water drain out before lifting from the pool, do it slowly so as to prevent back injury.
• Clean the filter basket after each cleaning cycle.
• Do not lift the robot out of water by track.

REMINDER

• When the robot battery is below 30%, it will only clean the floor of the pool.
• Storing your robot:
  • Ensure the robot is fully dry before storage. This prevents degradation or damage to the motors or internal structure.
  • The filter basket should be cleaned thoroughly after usage and do not leave dirt or debris to dry in filter basket.
  • The charger cable is stored neatly without twists whilst in long-term storage.
• Optimum storage temperature between -10-45℃ and storage humidity between 30%-70%/RH.

PRODUCT OVERVIEWS

Packaging content
The following items are included in the packaging of robot. Please contact your dealer if any damage or loss.

1. The robot
2. Charger
3. Hook
4. Magnetic cap*2
5. User manual

Note

1. Remove the Magnetic cap ④ when using or charging. Insert Magnetic cap back to machine’s bottom for battery protection if not using the robot for more than 14 days.
2. If the robot fails, insert the Magnetic cap ④ back for 2 seconds, remove the magnetic cap ④ and restart the robot.

Technical specification

Endurance condition reference: Floor mode
Endurance time| 8,0h| 6,0h| 4,5h| 3,0h
Endurance condition reference: Floor/wall/waterline mode
Endurance time| 4,5h| 3,5h| 2,5h| 2,0h
Charging time| 8,0h| 6,0h| 4,5h| 3,0h
Battery| 14,0Ah (352wh)| 10,4Ah (262wh)| 7,8Ah (196wh)| 5,2Ah (131wh)
Optimum pool temperature| 4~35℃
Cleaning mode| Floor only; Floor/Wall/Waterline
Multiple cycle option| 0,5h/1,0h/2,0h/Full Run
AI Timer| Clean every 24h/48h/72h
App application| YES
Filter capacity| 3,2L
Filtration accuracy| 100μm
Pump flow rate| 22-15(m³/h)| 20-15(m³/h)
Running power| 30-110W
Moving speed| 12m/min
Number of motors| 3
Charger input| 100-240VAC ~ 50/60Hz
Running voltage/current| 25,2V/1,2A
Charger power| 72,5W
Robot NW/GW| 12,0 / 17,0kg| 12,0 / 17,0kg| 11,5 / 16,5kg| 11,5 / 16,5kg
Robot dimension (LWH)| 495395265 mm
Robot packaging dimension

(LWH)

| 580448330 mm

• Reference: Above working time is based on 2 hours’ cleaning each time at floor mode in the liner pool.

Note: The manufacturer reserves the right to modify these specifications without notice.

Preparation

① Remove the Magnetic cap from the bottom of the robot and store it well.

| ② Remove the plug cover. When fully charged, cover the plug again.

---|---
③ Connect to the power(100-240V) supply using the charger supplied.

Battery 3 bars green lights on：Battery level: 100% Fully charge the robot before the first use.

*Suggested Charging Temperature: 6-35℃ ****

| ④ Install the configured hook on the rod (Rod is exclusive).

OPERATION

CAUTION
To prevent possible damage to the robot or people, be sure to follow these guidelines:

• After cleaning is completed, place the robot in a cool dry place away from direct sunlight.
• Take care when moving robot from pool and allow water to drain from robot before lifting.

IMPORTANT

• Once the robot is set up, drop into the water within 3 minutes or the robot will enter sleep mode.
• Clean the filter basket after the cleaning cycle. Avoid cleaning the surface of the filter box directly with your hands.
• The robot has a safety feature that automatically stops if not run in a pool with water.
• Turn the robot in all directions to release any air trapped in the robot before it enters the water. Shown below.

Overview of Control Panel

Operation on the display of the unit

1. Hold for 3 seconds to activate the robot. When flashes, start robot set up. After setup, press again as confirmation. Once completed, put the robot into the water. The robot will start cleaning automatically when it touches the floor. If there is no operation on the robot within 3 minutes from flashes, the robot will shut down and enter sleep mode.
   Note : There are two different outcomes when setting up the AI Timer:
   (Take set of “Cleaning every 24 hours” in AI Timer for example)

   • Press  once and put the robot into the water. The robot will start immediately. After one clean cycle, the robot will enter sleep mode and automatically wake up after 24 hours.
   • Press for 3s and then put the robot into the water. The robot will enter sleep mode. After 24 hours,  the robot will automatically wake up and start cleaning.

2. If the battery is less than 15% during the cleaning cycle, will keep flashing a red light, the robot will self-park at the pool side. It will enter sleep mode after 5 minutes.

Cleaning the filter basket
After a cleaning cycle, the robot will self-park at the pool side. Use the hook to catch the handle and lift the robot out of the water, drain the water from the robot and clean the filter basket as shown below:

Note:
To prevent injury, wear rubber gloves when cleaning the filter basket.

Charging the robot

1. Plug the adapter into power supply and make sure that indicator light is being green.
2. Open the cover of the robot’s plug to plug the adapter.
3. If the battery 3 bars green lights are on, the robot is fully charged.
4. Before charging, make sure charging port is dry.
5. Disconnect the charger after charging to protect the battery.
6. Charging plug should be inserted before robot use.
7. If the robot needs to be stored for long time, it should be fully charged at least every three months to protect.

Note: Use the original power adaptor with the robot ONLY.

WIFI Matching

Attention

1. Turn on Bluetooth & Wifi before APP connection.
2. Make sure the Wifi network connected is 2.4GHz and in a good signal.
3. Allow APP access to Bluetooth.
4. Make sure is flashing during APP connection.

Hold for 3s, then the robot will have a beep sound, the robot enters matching mode, start flashing, open the “AI-BOT” APP to search device and match the robot to your network and go matching, the robot will beep three times and will turn green after network is matched.
Setup of the robot can be operated via the APP through Wifi or Bluetooth.
Setup of the robot cannot be operated by APP if the robot is in the pool. (Due to the physical limitation of radio signal penetration in water).

Note: download the “AI-BOT” APP in iOS App Store/ Google Play Store.

MAINTENANCE

WARNING

1. To avoid electric shock and other hazards which could result in major injuries, disconnect the adapter from the power source before performing any cleaning and maintenance.
2. Before any maintenance, insert the magnetic cap back to avoid injuries caused by impeller rotation.

Filter maintenance

1. Clean the filter thoroughly and regularly for better cleaning and climbing performance. Otherwise, the cleaning and climbing performance may be affected when the filter is full or clogged.
2. Annually clean the clogged filter with mild acidic detergent, suitable safety equipment must be worn when during the process.

Impeller maintenance
Visually check whether the impeller or impeller shaft is entangled with hair or other debris when the robot has a reduced suction or climbing performance, clean the debris trapped in the impeller.

*The magnetic cap MUST be inserted back before any maintenance on the impeller.

Follow the below steps:

1. Take out the filter box, remove the fixing screws of the inflow ring cover, and take out the inflow ring cover.
2. Remove the deflector fixing screws and take out the deflector.
3. Remove the impeller screw and take out the impeller. Note: Wear gloves when removing the impeller to prevent injury from sharp edges.
4. Clean the impeller debris and reassemble all the parts mentioned above in order.

Note: If you have any difficulty with impeller maintenance, contact the dealer for assistance.

Replace the worn brushes
Remove the worn brushes & position the new brushes:

1. Unfasten the tabs from the holes and remove the brushes.
2. Fit the side without tabs under the brush holder.
3. Roll the brush around its support, slide the tabs into the attachment holes and pull on the end of each tab until its edge passes through the slit.

Replace the worn tracks
Remove the worn tracks:

Position the new tracks:

TROUBLESHOOTING

Charging failure

| Debris on the electrode of charging head (Non-failure)| Clean debris
The bottom Magnetic cap isn’t removed   (Non-failure)| Remove the Magnetic cap
The charging kit is damaged| Replace the charging kit

**** Switching on failure

| The Magnetic cap isn’t removed (Non-failure)| Remove the Magnetic cap
Water spots on the robot display or people’s hand (Non-failure)| Keep the display and hands dry, then try again
Wrong operation (Non-failure)| Hold the power button for 3 seconds
No power in the battery (Non-failure)| Get the robot fully charged

Not working (not moving, not pumping)

| Low battery (Non-failure)| Get the robot fully charged
Out of water (Non-failure)| Make sure the robot under water and the indicator lights are on
No pressing the on/off button after settings are done(Non-failure)| Press the on/off button after the settings are done, make sure indicator lights are on before putting the robot into

water

Full load of filter basket (Non-failure)| Clean filter basket

Moving but not pumping

| ****

**** The impeller gets stuck

| Check whether there is too much debris in the guide ring, affecting the rotation of the impeller. (Please insert back the magnetic cap before operation, to avoid injuries caused

by the impeller rotation)

Full load of filter basket (Non-failure)| Clean filter basket
Water inlet is blocked(Non-failure)| Take out of filter basket and clean water inlet
Battery low (Non-failure)| Get the robot fully charged
Pumping but| The moving motor gets stuck| Please contact the dealer for a replacement
not moving| The track is deviated and stuck

**** (Non-failure)

| Turn the robot upside down and roll the track forward and backward to restore the track
---|---|---
Track is damaged| Replace track
Scrubber gets stuck (Non-failure)| Clean scrubber
The robot gets stuck by obstacle and shut down for auto-protection (Non- failure)| **** Remove the obstacle and restart
Full load of filter basket (Non-failure)| Clean filter basket

Not climbing

| Under floor cleaning mode

**** (Non-failure)

| Turn to overall cleaning mode
**** The impeller is stuck| Check whether there is too much debris in the guide ring, affecting the rotation of the impeller. (Please insert back the magnetic cap before operation, to avoid injuries caused

by the impeller rotation)

Full load of filter basket (Non-failure)| Clean filter basket
Water inlet is blocked (Non-failure)| Take out of filter basket and clean the water inlet

**** Poor cleaning capability

| Battery low (Non-failure)| Get the robot fully charged
The impeller is stuck| Remove any debris or hair in the guide ring
Full load of filter basket (Non-failure)| Clean filter basket
Water inlet blocked (Non-failure)| Take out of filter basket and clean the water inlet
Scrubber is damaged| Replace scrubber
Filter basket is damaged| Replace filter basket
Unusual non-stop| Software failure| Insert the magnetic cap back for 5s, then remove it and restart
**** Error code|

1. Left drive failure
2. Right drive failure
3. Water pump failure
4. Control panel communication failure
5. Infrared sensor failure
6. Water sensor failure

| **** Restart the robot by the magnetic cap to check if the code disappears, if not, please contact the dealers

Note

1. Do not use the robot when people or animals are in the pool.
2. Charger MUST BE DISCONNECTED before performing any maintenance on the robot.
3. Contact dealer for problems not include in Trouble Shooting Guide.
4. Normally, the robot will stop at the poolside when it encounters any failure or when the battery is less than 15%.
5. If an error occurs, please restart the robot by inserting back the magnetic cap at the bottom of the robot.
6. If the robot is malfunctioning, the error code will appear on the control panel (see 2.1) and the power button on the control panel flashes red. Pressing the power button might remove the error warning and allow operation, if error occurs again, please check troubleshooting guide.

Indoor

For switch power supply indoor use only.

Recycling
The robot contains a Lithium-ion battery, which should be recycled by qualified battery electronics recyclers. Recycling of batteries and battery- containing products benefits the environment and human health.
Do NOT disassemble or dispose of the battery in the rubbish or municipal recycling bins.

Warranty Exclusions

Warranty is invalid if any of the following apply:

• Incorrect operation of the unit by not following correct instructions.
• Damage caused to the robot due to misuse or damage caused by any other means than manufacturer defect.
• If robotic pool cleaner is repaired or serviced by an unauthorized dealer or service station.
• If an unauthorized service station damaged battery seal.
• If you overcharge the battery by using a non-specified input power adapter.
• If you cause a fault in the operation of the machine by using non-specified accessories.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>