amazon basics B0B12SFRFD 9000 BTU Round Tabletop Propane Gas Fire Pit Instruction Manual

9,000 BTU Round Tabletop Propane Gas Fire Pit
Instruction Manual

B0B12SFRFD 9000 BTU Round Tabletop Propane Gas Fire Pit

DANGER
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a camper, tent, car or home.
DANGER: FIRE OR EXPLOSION HAZARD
If you smell gas:

• Shut off gas to the appliance.
• Extinguish any open flame.
• If odor continues, leave the area immediately.
• After leaving the area, call your gas supplier or fire department.

Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.
WARNING
Do not store or use gasoline, or other flammable vapors and liquids, in the vicinity of this or any other appliance.
An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
WARNING: For Outdoor Use Only.
Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
WARNING
If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

Important Safeguards

Read these instructions carefully and retain them for future use. If this appliance is passed to a third party, then these instructions must be included.
When using the appliance, basic safety precautions should al lways be followed to reduce the risk of injury including the following:
WARNING: Risk of injury!

• Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the area of the appliance.
• Clothing or other flammable materials should not be hung from the appliance or placed on or near the appliance.
• Any guard, barrier, or other protective device removed for servicing the appliance shall be replaced prior to operating the appliance.
• Repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners, and circulating air passageways of the appliance are kept clean.

CAUTION: Risk of burns! Hot surface!
Do not touch the glass wind guard (E) while the fire is lit or while the appliance is cooling down after being turned off.

• Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control that has been under water.
• Do not burn solid fuels in this appliance.
• The appliance is intended to be used with a standard 1 b (0.45 kg) LP gas cylinder (not included). Do not connect the appliance to an LP gas cylinder that exceeds this capacity.
• Use the appliance only outdoors. Do not use the appliance in a building, garage, or any other enclosed area.
• The appliance is not intended to be installed in or on recreational vehicles and/or boats.
• Keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.
• Only use the fire glass provided with the appliance.
• Do not use wood chunks, charcoal, lighter fluid, alcohol or other similar chemicals. Keep all such substances and liquids well away from the appliance when in use.
• Do not obstruct the flow of combustion and ventilation air to this appliance.
• Never operate this appliance unattended.
• Install the appliance properly on a table with a standard 2″ (5 cm) umbrella hole. Do not attempt to move the table when the appliance is in use.
• Always check for gas leaks when connecting or disconnecting an LP gas cylinder to the gas regulator, especially after a prolonged storage period.
• The appliance is intended only for operation in temperatures above 32 °F (0 °C).
• This appliance is intended for decorative purposes only. Do not use the appliance for cooking.
• After using the appliance, turn the control knob clockwise to switch the appliance off and disconnect the LP gas cylinder from the gas regulator. Allow the fire to burn itself out and do not pour water on the appliance.
• This appliance must be mounted by an adult.
• Keep children and pet away while assembling the appliance.
• Do not use this appliance if any parts are missing, damaged, or worn,
• Do not over-tighten the fasteners.
• Do not use the appliance in rainy conditions.
• For installations at elevations above 2000 ft (610 m), contact your local dealer or gas supplier before installing. Input ratings should be reduced approximately 4 % for each 1000 ft (305 m) above sea level. Refer to the National Fuel Gas Code, ANSI Z223.1.
• The appliance (excluding the glass wind guard) has been tested by CSA Group and was certified to meet the requirements set in the safety standard ANSI Z21.97-2017 / CSA 2.41-2017 for Outdoor Decorative Gas Appliances.

Before First Use

DANGER: Risk of suffocation!
Keep any packaging materials away from children and pets — these materials are a potential source of danger, e.g. suffocation.

• Remove all the packing materials.
• Remove and review all components before starting assembly.
• Check the appliance for transport damages.
• Clean the appliance before first use. The appliance may emit a slight smell or smoke when it is first used. This is entirely safe and harmless.

Product Description

A. Fire bowl
B. Blowout box
C. Burner
D. Control knob
E. Glass wind guard| F. Fire glass, 1 bag (8.8 lbs/ 4 kg)
G. Cylinder holder
H. Bracket
I. Fixing nut
J. Screws, x2
---|---

Preparation

4.1 Choosing a suitable location

• The appliance is for outdoor use only. Do not use it inside a building, garage, or any other enclosed areas.
• Place the appliance in locations with adequate fresh air ventilation.
• Maintain proper clearances from combustible structures. Keep a minimum clearance of 36 inches (91 cm) from sides and rear, and 60 inches (1.5 m) from the top of the appliance to combustible structures.

NOTICE: Combustible materials are materials made of or surface with wood, compressed paper, plant fibers, or other materials that are capable of being ignited and burned. Such material shall be considered combustible even flame- proofed, fire-retardant treated, or plastered. Combustible materials include lattice, wood, plants, umbrellas, canopies, awnings and similar items.

• The appliance can also be used within the following structures:
  — With walls on all sides, but with no overhead cover– Within a partial enclosure that includes an overhead cover and no more than two sidewalls in parallel, asina breezeway– Within a partial enclosure that includes an overhead cover and no more than two sidewalls at right angles to each other– Within a partial enclosure that included an overhead cover and three sidewalls, as long as 30 percent or more of the horizontal periphery of the enclosure is permanently open

• Do not store a spare LP cylinder under or near the appliance. Keep a minimum distance of 10 feet (3 meters) away from the appliance.

• Keep children and pets away from the appliance. When children are near the appliance, they should be carefully supervised by an adult.

• Combustible materials, gasoline, and other flammable vapors or liquids should be situated at least 26 feet (8 meters) away from the appliance.

4.2 Setting up the appliance
NOTICE

• This appliance should be installed, maintained and operated only by an adult. If in doubt, consult a professional.
• Install the appliance only to a table with a standard 2″ (5 cm) umbrella hole (not included). The tabletop must be between 0.79″ (2 cm) and 1.18″ (3 cm) in thickness and be capable of supporting the weight of the appliance and a standard 1 Ib (0.45 kg) LP gas cylinder.
• The appliance is safe to use on wood, wicker, and composite tables.

1. Install the cylinder holder (G) to the bracket (H) using 2 screws (J) (Fig. 1).
2. Unscrew the fixing nut (l) from the threaded connector on the bottom of the fire bowl (A) (Fig. 2).
3. Place the fire bowl (A) on a suitable table with the connector of the gas regulator passing through the 2″ (5 cm) umbrella hole (Fig. 3).
4. Adjust the feet if needed to ensure that the appliance sits leveled on the table (Fig. 4).
5. Secure the cylinder holder assembly in place by tightening the fixing nut (I) underneath the table (Fig. 5).
6. Fit the glass wind guard (E) to the fire bowl (A) (Fig. 6).

4.3 Picking a suitable LP gas cylinder
DANGER Risk of fire!

• Do not store a spare LP gas cylinder under or near this appliance.
• Never fill the cylinder beyond 80 % full.
• If the information above is not followed exactly, a fire causing death or serious injury may occur.

• The liquefied petroleum (LP) cylinder must be constructed and marked in accordance with the specifications for LP Gas Cylinders of the U.S. Department of Transportation (D.O.T.) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission.
• The appliance must be used with a standard 1 lb (0.45 kg) LP gas cylinder (not included) marked “propane”.
• Do not use an LP gas cylinder if it has a damaged valve, or shows signs of dents, gouges, bulges, fire damage, corrosion, leakage, excessive rust, or other forms of visual external damage. Have the LP gas cylinder checked immediately by a liquid propane supplier.

Connecting/Disconnecting a Gas Cylinder

5.1 Connecting an LP gas cylinder

1. Push in the control knob (D) and turn it clockwise to switch the appliance off (Fig. 7). Release the control knob (D).
2. Push an LP gas cylinder into the cylinder valve outlet and turn clockwise by hand to secure it in place. Do not overtighten (Fig. 8).
3. Tighten the wing nut on the cylinder holder (G) to secure the LP gas cylinder in place (Fig. 8).

5.2 Disconnecting an LP gas cylinder
WARNING:Risk of fire or explosion!

• Disconnect the LP gas cylinder when the appliance is not in use.
• Do not transport or store the appliance with the LP gas cylinder connected. Before transport or storage, disconnect the LP gas cylinder and store it outdoors.
• Do not disconnect the LP gas cylinder while the appliance is in use or is still hot.

1. Push in the control knob (D) and turn it clockwise to switch the appliance off (Fig. 7). Release the control knob (D).
2. Loosen the wing nut on the cylinder holder (G) (Fig. 9).
3. Turn the LP gas cylinder counter-clockwise by hand to disconnect from the cylinder valve outlet of the gas regulator (Fig. 9).

Gas Leak Test

DANGER: Risk of explosion!

• Perform a gas leak test on the connection between the gas regulator and the LP gas cylinder when lighting the appliance for the first time, when the LP gas cylinder has been refilled/changed, after a travel over rough or bumpy roads or after a prolonged period of storage or non-use.
• Do not smoke or use any type of flammable material in the area during this gas leak test.
• Do not use an open flame to check for leaks. Always use a soapy water solution.

1. Push in the control knob (D) and turn it clockwise to switch the appliance off (Fig. 7). Release the control knob (D).

2. Connect an LP gas cylinder to the cylinder valve outlet of the gas regulator.

3. Mix a solution of one part of water with one part of liquid soap in a clean bowl (not included) (Fig. 10) with a paint brush (not included).

4. Use the paint brush to apply the solution on the connection between the cylinder valve outlet and the LP gas cylinder (Fig. 11).

5. Visually inspect for streams of bubbles coming from the connection points. This indicates that there is gas escaping.
   • If no gas bubbles appear at any connections, the connections are secure.
   • If a leak appears, repeat connecting the LP gas cylinder to the cylinder valve outlet of the gas regulator. Perform a gas leak test after reconnection to ensure a secure and leak-free connection.
   • If aleak continues to appear after reconnection, do not use the appliance. Have the LP gas cylinder checked immediately by a liquid propane supplier.

6. Wipe the LP gas cylinder and the cylinder valve outlet of the gas regulator dry with a soft cloth.

Operation

WARNING: Risk of injury!

• Only use the appliance when it is completely assembled, with all parts securely fastened and tightened.
• Always inspect the appliance for gas leaks, obstructions on the burner (C) and for any abrasion or wear.
• Keep the appliance away from high wind areas but keep it in a well-ventilated area.

CAUTION: Risk of burns! Hot surface!
Do not touch the glass wind guard (E) while the fire is lit or while the appliance is cooling down after being turned off.
CAUTION: Risk of burns!
The appliance becomes very hot while in use.
Use heat-resistant gloves, long-handled tongs or insulated mitts at all times.
NOTICE: Always fit the glass wind guard (E) properly to the fire bowl (A) to protect the flames from wind and prevent foreign objects from accidentally blowing into the fire bowl (A) and catching fire. The use of glass wind guard (E) ensures cleaner burning of the gas and thus reduces the sooting on the fire glass (F).
7.1 Checklist before lighting

1. Read the instruction manual to understand correct operation and precautions.
2. Check that all components are properly assembled, intact and operable.
3. Visually inspect the appliance for any signs of blockage (debris, insects) on the burner (C) or in the burner portholes.
4. Asuitable LP gas cylinder is used (refer to chapter 4.3 Picking a suitable LP gas cylinder).
5. Make sure that the top of the LP gas cylinder is clear of debris. Be sure any parts removed during assembly or servicing are replaced and fastened prior to starting.
6. No alterations have been made to the appliance.
7. LP gas cylinder is connected correctly (refer to chapter 5.1 Connecting an LP gas cylinder).
8. Connections of the appliance and the LP gas cylinder checked for gas leaks (refer to chapter 6. Gas Leak Test).
9. Location of the appliance is suitable (refer to chapter 4.1 Choosing a suitable location).

7.2 Lighting instructions
WARNING: Risk of fire or explosion!

• Read instructions before lighting.
• Do not use spirit, lighter-fluid or petrol for lighting or relighting.
• If you hear a hissing sound or see/smell gas escaping from the connected LP gas cylinder, do not attempt to light the appliance. Disconnect the LP gas cylinder, and reconnect it. If the problem persists, have the LP gas cylinder checked by liquid propane supplier.
• Always visually inspect the appliance before lighting. Ensure that there are no signs of blockage (debris, insects) on the burner (C) or in the burner portholes.

WARNING: Risk of injury!

• Never use wet fire glass (F) in the appliance. Wet glass can explode or fly out of the appliance.
• Fire glass (F) remains hot for some time after use. Let them cool down for at least 30 minutes before removing from the fire bowl (A).

1. Push in the control knob (D) and turn it clockwise to switch the appliance off (Fig. 7). Release the control knob (D).

2. Place provided fire glass (F) on the fire bowl (A) to cover the burner (C) (Fig. 12).
   NOTICE: Do not block the vents on the top of the blowout box (B) with the fire glass (F).

3. Connect an LP gas cylinder to the cylinder valve outlet of the gas regulator (refer to chapter 5.1 Connecting an LP gas cylinder).

4. Push in the control knob (D) and turn it 90 degree counter- clockwise to the high setting until you hear a “click” sound which indicates a spark from the igniter.

5. Release the control knob (D). Look for flames to ensure the burner (C) is lit.
   NOTICE: If ignition does not occur in 5 seconds, turn the control knob (D) clockwise to switch the appliance off. Wait 5 minutes to allow any accumulated gas to dissipate before attempting to relight the burner (C).

6. After the burner (C) is lit, adjust the temperature setting as desired using the control knob (D).

7.3 After use

1. Push in the control knob (D) and turn it clockwise to switch the appliance off (Fig. 7).
2. Disconnect the LP gas cylinder (Fig. 9).

7.4 Flame pattern
NOTICE: After lighting, perform periodic and visual checks of the burner flames.

• A correct flame should be primarily blue with a yellow tip (Fig. 13).
• Anincorrect flame is excessively yellow, orange or irregular (Fig. 13). If this is the case, clean the burner (C) and burner portholes to increase airflow.

Cleaning and Maintenance

WARNING: Risk of injury!
Repair and maintenance should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners, and circulating air passageways of the appliance are kept clean.
8.1 Cleaning
WARNING: Risk of injury

• Before cleaning and maintenance turn the control knob (D) clockwise to switch the appliance off and allow the appliance to cool down. Disconnect the LP gas cylinder prior to cleaning.
• Clean the appliance regularly to prevent excessive flare- ups.

WARNING: Risk of injury!
Check and clean the burner (C) regularly for insects and insect nests. In cases of severe blockage, the flames may burn backwards, and outside of the burner (C).
NOTICE: To clean the soot off the fire glass (F), use a 1:1 ratio of diluted vinegar and water. Let the fire glass (F) dry completely before next use.

• To clean the appliance, wipe with a soft, slightly damp cloth.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the appliance.
• Clean the outer surface of the burner (C) to remove dirt with a wire brush.
• Clean any blocked burner portholes with a stiff wire such as an open paper clip.

8.2 Storage
8.2.1 Storing the appliance
CAUTION: Risk of injury!
Storage of the appliance indoors is permissible only if the LP gas cylinder is disconnected and removed from the appliance.

• Disconnect the LP gas cylinder.
• Store the appliance in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust, and debris).
• Allow the appliance to cool down completely. Cover the appliance with a waterproof protective cover (not included) to protect it from rain, leaves and debris.

8.2.2 Storing the LP gas cylinder
DANGER: Risk of explosion!
Do not smoke or use any type of flammable material in the area while moving the LP gas cylinder.
CAUTION: Risk of injury!
Store the LP gas cylinder outdoors out of reach of children. Do not store it in a building, garage or any other enclosed area.

• Never leave the LP gas cylinder exposed to direct sunlight or excessive heat.
• Store the LP gas cylinder only in upright position.
• Check for leaks after long periods of storage. Perform a gas leak test (refer to chapter 6. Gas Leak Test) before using the appliance.

8.3 Transport
DANGER: Risk of explosion!
Do not smoke or use any type of flammable material in the area while moving the LP gas cylinder.

• Disconnect the LP gas cylinder and allow the appliance to cool down completely before transport.
• When transporting the appliance in a vehicle, secure it in place using bungee cords or similar means.

8.4 Maintenance
Regularly check that all the components and fasteners are tightened.
8.5 Spare parts/replacement parts
WARNING: Risk of injury!
Using parts that are not compatible with the appliance may cause accidents that can result in serious injury.

Frequently Asked Questions

new one or have it refilled by a liquid propane supplier.
• The regulator hose assembly is kinked. Straighten the hose.
The burner blows out.| • Set the control knob to a higher setting.
• The LP gas cylinder is empty. Change it with a new one or have it refilled by a liquid propane supplier.
• Check if there is any sign of blockage (debris, insects) on the burner or in the burner portholes. Clean and unclog the parts properly.
There are frequent flare- ups.| • Set the control knob counter-clockwise to a lower setting.
• Check if there is any sign of blockage (debris, insects) on the burner or in the burner portholes. Clean and unclog the parts properly.
There is sign of gas leakage.| • Turn the control knob clockwise to switch the appliance off. Reconnect the LP gas cylinder to the cylinder valve outlet of the gas regulator. Perform gas leak test to ensure leak-free connection.
• Change the LP gas cylinder if corroded, rusted or damaged.
• The gas regulator is damaged. Contact a professional repair center for repair or replacement.
The fire glass turns black.| Remove some fire glass from the fire bowl. Use 1 to 2 inches of fire glass to cover the burner. Do not overfill the fire bowl.
Burner flames are yellow or orange.| • The LP gas cylinder is empty. Change it with a new one or have it refilled by a liquid propane supplier.
• Check if there is any sign of blockage (debris, insects) on the burner or in the burner portholes. Clean and unclog the parts properly.
Smell gas or a “rotten egg” odor.| Propane suppliers add a distinctive “rotten egg” odor to propane because it is odorless. If user smells gas or this odor, disconnect the LP gas cylinder from the cylinder valve outlet of the gas regulator. If the odor remains, call the fire department immediately as there is a risk that the LP gas cylinder is not properly sealed and is leaking. Do not try fix the leaking LP gas cylinder yourself.

Disposal

Dispose of the appliance according to local regulations. If in doubt, consult your local authorities.

Specmcatlons

Feedback and Help

We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.
Scan QR Code below with your phone camera or QR reader:

https://www.amazon.com/review/review-your-purchases/listing/?ref=HPB_UM_CR

You need help with your Amazon Basics product, please use thewebsiteiornumber below:

amazon.com/gp/help/customer/contact- us
+1877-485-0385
amazon.com/AmazonBasics
MADE IN CHINA
V02-09/22

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>