Lexman 3135706 Digital Socket Energy Monitoring User Manual

*5 GUARANTEE YEARS
DIGITAL SOCKET
ENERGY MONITORING E TYPE
**

EAN CODE: 3276007458312
ADEO KEY : 84586356
2022/08-V01
Instructions manual

Limited warranty and liability

LEXMAN guarantee that the product is free from any defect in material and workmanship within five year from the purchase date. This warranty does not apply to damages caused by accident, negligence, misuse, modification, contamination or improper handling. The dealer shall not be entitled to give any other warranty on behalf of LEXMAN. If you need warranty service within the warranty period, please contact your seller directly. LEXMAN will not be responsible for any special, indirect, incidental or subsequent damage or loss caused by using this device. As some countries or regions do not allow limitations on implied warranties and incidental or subsequent damages, the above limitation of lisbility may not apply to you.

Accessories

Open the package box and take out the meter. Please double check whether the following items are missing or damaged.
a) User manual ………………….. 1pc
b) DIGITAL SOCKET ENERGY MONITORING E TYPE ……….. 1pc
If any of the above is missing or damaged, please contact your supplier immediately.

Safety introduction

This product is adapted to control: lamp, lighting chain, automatic watering system, aquarium, small heater, coffee machine.
Do not use the product if there is any damage or defect on the product.
Do not open or repair the product by yourself but request it to a professional worker.
To clean the product, remove it from the wall socket and use a soft, dry cloth.
Keep the product out of access to the childrens.
Do not put a load to the product over than the maximum indicated.
Do not plug a multi socket on the product output.
Plug the product only to a wall socket equipped with a earth connection.
Do not plug this kind of product in series.
Avoid humidity, extreme temperatures, vibrations & shocks.
Risk of electrical shock! do not open the product. No part can be repaired by the user.
The product is power off only when it is unplugged from wall socket.
– this product contains a lithium battery
– keep new and used batteries out of reach of childrens
– if battery is swallowed it can provoke severe internal burns and can provoke the death in only 2 hours
– contact immediately a doctor a in case of swallowing
– remove the battery and keep it is a safe area if you don’t use the product during a long period
– risk of explosion if the battery is not correctly placed
– replace the battery only with the same battery type
– the battery does not have to be exposed to excessive temperature as sun exposure, fire

WARNINGS! KEEP OUT OF REACH OF CHILDREN. Swallowing can lead to chemical burns, perforation of soft tissue, and death. Severe burns can occur within 2 hours of ingestion. Seek medical attention immediately.

Keep the batteries out of the reach of children. There is a risk of children or animals swallowing them. Consult a doctor immediately if a battery is swallowed.

General specifications

Statement of the range of environmental
conditions| A.Indoor use,
B.2000M altitude
C.CAT II
D.OVERVOLTAGE Category: 2
E.Pollution degree of the intended environment: 2

General features

Display current time (CLOCK).
Display line voltage (VOLTac).
Display line current (AMP).
Display line power (WATT).
Display and memory accumulative total electric quantity (kWh).
Display and memory total on time and total electric charge (TOTAL PRICE).
Display and memory total on time and total electric charge of price1 (TOTAL PRICE 1).
Display and memory total on time and total electric charge of price2 (TOTAL PRICE 2).
Display line frequency (Hz).
Display power factor (POWERFACTOR).
Adjustable price / kWh
11 combinations of day or blocks of days available as follows:
MO>TU>WE>TH>FR>SA>SU>MO,TU, WE, TH, FR>MO,TU, WE, TH, FR, SA>SA, SU>MO, TU, WE, TH, FR, SA, SU

Button description

1. UP key
2. SET key
3. FUNC key
4. RESET key

Install battery

Insert the 3 pcs batteries (LR44/AG13) according to the correct direction indication, close the cover of battery. Press RESET button after insert batteries. Now the power meter is ready to be set up for use.
Note:

1. The cover must be in place before use.
2. The batteries must be taken out if not use for long time.
3. The changing of batteries is only allowed if the equipment is disconnected from the main power.
4.  The batteries shall not been disposed into the garbage.
5. Leaking batteries installed in the equipment might cause an electric shock.
6. The power meter may not work with open batteries cover.
7. The min distances is 8 mm for batteries are the clearances, creepage distances.

Set current time
Press FUNC button until the CLOCK displays in the screen.
Press SET button once and release, “WEEK DAY” is flash. Press UP button to set current day.
Press SET button once again to advance to hour setting, “HOUR” is flash. Press UP button to set current hour.
Press SET button once again to advance to minute setting, “MINUTE” is flash. Press UP button to set current minute.
Press SET button one more time to complete the setup.
Repeat above steps to reset current time.
While programming, press FUNC button once to exit CLOCK setting mode.
While the meter is at CLOCK display state, press UP button to turn the time display between 12 and 24 hour mode.

Setting price of COST/kWh

1. While the meter displays voltage, current or power, press and hold FUNC button for 3 seconds to enter into PRICE 1 setting.
2. Press SET button once and release, “SET” displays in the screen. The first digital of COST/kWh is flash, press UP button to set it.
3.  Press SET button once again and release, the second digital of COST/kWh is flash, press UP button to set it.
4. Press SET button once again and release, the third digital of COST/kWh is flash, press UP button to set it.
5. Press SET button once again and release, the fourth digital of COST/kWh is flash, press UP button to set it.
6. Press SET button once again and release, the radix point of COST/kWh is flash, press UP button to set it.
7. Press SET button once again and release, -:– is flash, press UP button to select the desired day(s) of ON TIME.
8.  Press SET button once again and release, hour of ON TIME is flash, press UP button to set it.
9. Press SET button once again and release, minute of ON TIME is flash, press UP button to set it.
10. Press SET button one more time to complete PRICE 1 setting.
11. Press FUNC button once and release to enter into PRICE 2 setting.
    Repeat step 2-9 to complete PRICE 2 setting.
    Repeat above steps to reset PIRCE 1 and 2.
    While programming, press FUNC button once to exit PRICE setting mode.
    While the meter displays PRICE 1, press and hold FUNC button for 3 seconds to come back CLOCK display.
    While the meter displays PRICE 2, press and hold FUNC button for 3 seconds to delete ON TIME of PRICE 1 and 2. ON TIME displays -:–.
    After completing setting, plug the meter into a regular 230VAC power outlet. Plug in an appliance that you want to use and turn the mains power on. Now the meter begins to measure the consumption of the appliance and detect the equipment that uses too much electricity at once.

The data display

While the meter displays current time, line voltage and frequency, press FUNC button once and release. The meter displays current time, line current and power factor.
3. Press FUNC button once again and release, the meter displays current time, real power and power factor.
4. Press FUNC button once again and release, the meter displays current time, accumulative KWh and power factor,
5. Press FUNC button once again and release, the meter displays total electric charge (TOTAL PRICE) and total on time.
6. Press FUNC button once again and release, the meter displays total on time and total electric charge of PRICE 1.
7. Press FUNC button once again and release, the meter displays total on time and total electric charge of PRICE 2 .
8. Press FUNC button once again and release, the meter comes back display current time, line voltage and frequency.
9. While the meter displays total electric charge or total electric charge of price 1 or total electric charge of price 2, press and hold FUNC button for 5 seconds to clear accumulative total electric quantity and total electric charge.
10. While total electric quantity or total electric charge overflow, —- displays in the screen.

Stand by mode
If no button is pushed for 10 seconds after AC power off, the screen will be blank. Press any button to resume the display.
Please note
If the internal battery runs out, the internal data is cleared when the power meter is unplugged from main power.
Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting point for environmentally friendly disposal in accordance with local regulations. Contact your local authorities or stockiest for advice on recycling. The packaging material is recyclable. Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection-service.
Batteries must be recycled or destroyed appropriately. Do not throw batteries away with household waste, municipal waste or on a fire as they may leak or explode. Do not open, short circuit or damage batteries as this may cause injury. (if sold with battery)

5-year guarantee
Translation of the original version of user manual .
ADEO Services – 135 Rue Sadi Carnot – CS 00001 59790 RONCHIN – France

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>