Lexman LX-M-102 Voltage Tester User Guide
- June 9, 2024
- lexman
Table of Contents
Lexman LX-M-102 Voltage Tester
SYMBOLS
The meaning of the symbols associated with this tester
Limited warranty and liability
ADEO guarantees that the product is free from any defect in material and workmanship within five years from the purchase date. This warranty does not apply to damage caused by accident, negligence, misuse, modification, contamination or improper handling ADEO will not be responsible for any special, indirect, incidental, or subsequent damage or loss caused by using this device.
Safety warning
This manual contains warning information and safety regulations. Please observe them strictly to ensure the safety of the user and tester.
Note
- Please read and understand all contents of the manual concerning safety, operation and maintenance before using the tester.
- ADEO is not responsible for any damage caused by improper use or violation of the safety regulations in the manual.
- This manual is subject to change without prior notice. The safety symbol «A» has three meanings in the manual. Users should pay special attention to the operation with the symbol when reading.
- Danger: identifies conditions and actions that are likely to pose serious or fatal hazards.
- Warning: identifies conditions and actions that may pose serious or fatal hazards.
- Caution: identifies conditions and actions that may pose minor injury or damage to the tester.
- To avoid electric shock, pay special attention when the measured voltage exceeds the personal safety (36V).
- Before each use verify tester operation by measuring a known voltage.
- Only touch the handle part in using the tester. Keep fingers behind the finger guards and away from the metal probe contacts when making measurements.
- Do not use the tester over range (400v).
- Do not use the tester or test lead if it appears to be damaged.
- Do not use the tester in extreme temperatures or wet weather.
- Keep the operating temperature between-15°C 45°C and relative humidity less than 85%.
- Safety is no longer guaranteed if:
- There is obvious damage.
- The functions of the tester are impaired.
- The tester has been stored at extreme temperatures for a long time.
Introduction
The Voltage Tester is an automatic voltage tester that tests ACIDC voltages from 12V to 400V. It is designed for electricians and homeowners alike. Ilis available for residential or commercial use, and test sockets, appliances, etc
Features
- Test ranges of ACIDC voltage: 12V, 24V, 50V, 120V, 230V, 400V
- Automatic identification of ACIDC voltage
- Automatic identification of DC voltage polarity
- Hazardous voltage indicator
- Complies with IP54, RoHS, CE and CAT I| 400V standards.
Structure
Operating instructions
In a safe operating environment, connect the test probes to the circuit under test. The voltage level indicators will illuminate indicating the voltage present. The range of the measured voltage can be judged based on the status of the indicators. When DC voltage is detected the «t» or «-» polarity indicator will illuminate, revealing the polarity. When AC voltage is detected, both polarity indicators will illuminate.
- If the range of measured voltage can be clearly determined, please stop testing. The testing time should be less than 5s lo ensure the service life of the tester.
- If the voltage under test Is less than 10V, the tester may not detect It At this time, the 12V LED voltage level Indicator may be on or off.
- Do not attempt to measure AC/DC voltage In excess of 400V under any circumstances. The hazardous voltage Indicator w/11 11/ruminate In the presence of voltage exceeding 50V AC or DC, with characteristics as detal/ed In the table below:
Specifications
General specifications
- Operating altitude: Up to 2000m.
- Relative humidity: <85% non-condensing.
- Operating temperature: -15°c-45°C
- Storage temperature: -20°C 60°C
- Dimensions: 265mm 42mm 27mm.
- Weight: 136g
- Drop protection: 2m
- Ingress protection: IP54
- Safety rating: CAT I1 400V
- Pollution degree: 2
- Recovery time: <5s
- Time rating: >600s
- 17ka@ELVa.c.: when voltage below 50Vac, the tester internal impedance is 17kQ
Electrical specifications
- Voltage level indicators:
- AC: 12V, 24V, 50V, 120V, 230V, 400V
- DC: 12V, 24V, 50V, 120V, 230V, 400V
- Polarity indicators
- DC Positive: (+) LED illuminated
- DC Negative: (-) LED illuminated
- Both (+/-) LED illuminated indicate AC
- Hazardous voltage indicator
- Solid on when voltage >50V
- Blinking at 1.5Hz when voltage >400V
- Input protection: 400V ACIDC
- Maximum measurable voltage: 400V ACIDC
- Accuracy: Voltage level indicators typically illuminate fully at approx. 70% to 100% of indicated voltage, except for 12V ACIDC (50% to 100%)
- AC frequency: 50Hz/60Hz
Maintenance and cleaning
- If an abnormal phenomenon occurs or the tester malfunctions during normal operation, please stop using It Immediately and contact your seller for confirmation.
- Remove the test probes from the circuit under test before cleaning. Wipe the tester surface with a clean, dry lint-free cloth. Do not use abrasive cleaners or solvents. Make sure the tester is ventilated and dry before using.
DISPOSAL
Electrical products must not be disposed of out with domestic waste. They must be taken to a communal collecting point for environmentally friendly disposal in accordance with local regulations. Contact your local authorities or stockist for advice on recycling. The packaging material is recyclable. Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection service. Don’t throw batteries or out-of-order products with household waste (garbage). The dangerous substances that they are likely to include may harm health or the environment. Make your retailer take back these products or use the selective collection of garbage proposed by your city.
warranty
- 5-Year warranty
ADEO Services
- 135 Rue Sadi Carnot- CS 00001
- 59790 RONCHIN France
Made in CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>