HOTATA 3108 Keyless Entry Door Lock with Keypad User Manual

HOTATA 3108 Keyless Entry Door Lock with Keypad

Product Information

Specifications

• Model No : 3108
• Version: 1.0
• Customer Service: 1 Year Warranty, Lifetime Customer Support
• Email: aftersale@hotata.com

Components List

• Keypad Assembly
• Deadbolt Strike Plate
• Battery Cover
• Key
• Deadbolt Latch
• Mounting Plate
• Interior Assembly
• 3/4(19mm) Screws-4 pcs
• 1-5/32(33mm) Screws-2 pcs
• 3/4(19mm) Screws-2 pcs
• Entry Key (2 ea.)
• Tools Required
• Optional Reinforcement screws (1 set)

Installation Guide
Prepare the door and check dimensions

1. Measure to confirm that the hole in the door is 2-1/8 (54mm).
2. Measure to confirm that the backset is either 2-3/8 or 2-3/4 (60 or 70mm).
3. Measure to confirm that the hole in the door edge is 1 (25mm).
4. Measure to confirm the thickness of the door is between 1-3/8 and 2 (35 and 50mm).

Install the latch and strike

1. Insert the latch bolt into the door.
   • Make sure the +-shaped hole is in the bottom position.
   • If adjustment is required, twist the latch and adjust the bolt length.
2. Install strike on the door frame.
   • Make sure the hole in the door frame is drilled a minimum of 1 (25mm) deep.

Install the exterior assembly
Locking lever transversal through the latch cable.

• Route the cable through the door below the bolt and push the keypad onto the door.
• The key must be pulled out when installing.

Install the interior assembly

1. Please confirm the door opening direction before installing.
   Find the direction switch under the Interior Assembly, and change the direction as per the instructions below:

   • Switch to the left (for left opening door).
   • Switch to the right (for right opening door).

2. Route cable through the bottom of mounting plate.

3. Tighten screws evenly. Note: please support exterior assembly during mounting plate installation.

4. Ensure tight cable connection.

5. Tighten screws evenly.

If the keypad and mounting plate are deflection, please loose mounting plate screws and adjust. If the latch does not extend or retract smoothly, please adjust mounting plate screws.

FAQ

• Q: Where can I find video tutorials for this product?
  A: You can check out our video tutorials available at https://www.youtube.com/@hotataaftersale/playlists
  or scan the QR code provided in the manual.

• Q: How can I contact customer support?
  A: You can email us at aftersale@hotata.com .

IMPORTANT: Read the instructions carefully before operating the appliance and keep them for future reference.

Customer Service

Email US : aftersale@hotata.com

Scan QR code for video tutorials Check out our video tutorials available at https://www.youtube.com/@hotataaftersale/playlists

Components List

Tools Required
Tools Required for Installation on Pre-drilled Doors: Phillips Screwdriver (DO NOT USE POWER DRILL!)

Installation Guide

Prepare the door and check dimensions
If drilling a new door, use the supplied template and the complete door drilling instructions.

Optional: For the best fix, you may need to drill an additional hole for the reinforcement screw.

1. Measure to confirm that the hole in the door is 2-1/8″（54mm)
2. Measure to confirm that the backset is either 2-3/8″or 2-3/4″(60 or 70mm)
3. Measure to confirm that the hole in the door edge is 1″(25mm)
4. Measure to confirm the thickness of the door is between 1-3/8″and 2″(35 and 50mm)

Install the latch and strike

1. Insert the latch bolt into the door.
2. Install strike on the door frame.

Install the exterior assembly

• Route the cable through the door below the bolt and push the keypad onto the door.
• The key must be pulled out when installing.

Install the interior assembly

1. Please confirm the door opening direction before installing.
   Find the direction switch under the Interior Assembly, and change the direction as per the instructions below:

2. .Route cable through the bottom of mounting plate.

3. Tighten screws evenly.

4. Ensure tight cable connection.

5. Insert key and test latch. if latch does not extend or retract smoothly. please adjust mounting plate screws.

6. Tighten screws evenly.

7. If the keypad and mounting plate are deflection. please loose mounting plate screws and adjust.

Install the batteries and test the lock
Note: Do not use rechargeable batteries or Non-alkaline batteries.

1. Install 4 AA batteries in battery pack.
2. Test the lock.
3. Press and hold , the latch bolt extends by itself.
4. Enter preset code: 1234, press , the latch bolt retracts by itself.

If the latch bolt doesn’t extend or retract smoothly ,please check the direction switch or re-install the lock. Green lights means successfully installed. Red lights means unsuccessfully installed.

Programming Guide

Factory Default Reset

• A factory reset will delete all codes associated with the lock.
• Find a paper clip, put it into the hole at the bottom, long press for 5 seconds, until the buzzer beeps.

Find a paper clip, put it into the hole at the bottom, long press for 5 seconds, until the buzzer beeps.

Change Programming Code

Important tips for programming：

1. For your safety, it is strongly recommended that you change and remember your programming code in time.
2. When you enter the wrong button, the system will exit the programming mode, and you can attempt programming procedure again.
3. If you do not enter any buttons within 5 seconds, the system will exit the programming mode, and you can attempt programming procedure again.

• If your lock is new, the factory preset code is: 123456 The new programming code must be 6 digits
• If the operation is successful:the green light and beeps 1 second.
• If the operation is wrong:the red light flashes 3 times with 3 beeps.
• If you do not enter any buttons within 5 seconds:the red light flashes 3 times with 3 beeps,system will exit the programming mode.

Programming Symbols

• Lock
• Unlock / Programming
• Programming Code
• User Code (4-8Digits)
• User ID (01-50) 2Digits

Factory default settings

• The lock is in experience mode
• Programming Code:123456
• User Code: 1234 or any 4-8Digits
• Indoor unlock / lock button
• Reset button

Advanced Setting Options

Add new user code

Delete User code

• After deletion, the user code will not be able to unlock
• If the operation is successful:the green light and beeps 1 second.
• If the operation is wrong:the red light flashes 3 times with 3 beeps.
• If you do not enter any buttons within 5 seconds:the red light flashes 3 times with 3 beeps,system will exit the programming mode.

System Alerts

Replacement battery
The red light and beep 1 second after press unlock button. And can not unlock| Super low battery
The keypad and lightindicator no respond| Battery run out| Use Type- C emergency power supply to unlock or key to unlock then replace battery
Bad cable connection| Re-connect the cable

lf you have any questions, please contact us at any time.
Email: Aftersale@hotata.com

FCC Warning

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

TEMPLATE

Scan the QR code or visit the link:https://www.youtube.com/@hotataaftersale/playlists
to watch video tutorials, which can help you better understand the installation and usage of the product. aftersale@hotata.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>