HINKLEY HF1161 MISTRAL Covered Outdoor Fan Instruction Manual

HINKLEY HF1161 MISTRAL Covered Outdoor Fan

WE WANT YOU TO LOVE YOUR NEW FAN

SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME HELP OR WANT TO CHAT ABOUT OUR PRODUCTS, SEND SUGGESTIONS OUR WAY TOO – WE’RE ALWAYS LOOKING TO MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE.

• SERVICE@HINKLEY.COM
• 800.HINKLEY
• LET’S SEE THAT HINKLEY STYLE @HINKLEY #HINKLEYSTYLE

This manual contains complete instructions for the installation and operation of this fan. It has been designed to make the installation process as easy as possible. If you are unfamiliar or uncomfortable with wiring, please contact a qualified electrician. If you need additional assistance or have any questions, please reach out to us.

For warranty information, visit hinkley.com.

NOTE : If PAIRING is necessary, refer to the control pairing instructions in the operations section of this Instruction Manual.

WARNING:

Read and follow these instructions carefully and be mindful of all warnings shown throughout.

GENERAL INSTALLATION & OPERATION INSTRUCTIONS

1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning.
2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and products, secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installation(s) and connections.
3. WARNING: To reduce the risk of fire, electric shock, or other personal injury, mount fan only on an outlet box or supporting system marked acceptable for fan support of 35 lbs (15.9 kg) or less and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
4. Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades should be at least 10 feet from floor.
5. Blades should be attached before motor housing is hung and in place. Fan motor housing should be kept in the carton until ready to be installed to protect its finish. If you are installing more than one ceiling fan, make sure that you do not mix fan blade sets, as each blade is part of a weighted set.
6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be spread apart with the common conductor and the grounding conductor on one side of the outlet box, and the “HOT” wires on the other side.
7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and should be installed per the light kit’s installation instructions.
8. After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling and/or causing damage or injury.
9. The fan can be made to work immediately after installation – the bearings are adequately charged with grease so that, under normal conditions, further lubrication should not be necessary for the life of the fan.
10. CAUTION: Do not ingest battery – Chemical bum hazard. Keep new and used batteries away from children.
11. The remote control supplied with a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal bums in just 2 hours and can lead to death.
12. If the battery compartment does not close securely, stop using the product and keep it away from children.
13. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
14. WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. JY1126T manufactured by Satellite Electronic (Zhongshan) Ltd.
15. Note: Suitable for use in damp locations. Use only with light kits marked “Suitable for use in damp locations.”

IMPORTANT SAFETY PRECAUTIONS

WARNINGS:

• Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.
• Support directly from building structure.
• To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
• Do not use an incandescent light dimmer. Do not use this fan with any transformer type fan speed control device.
• To reduce the risk of personal injury, do not bend the blade arms when installing them, balancing the blades or cleaning the fan. Do not insert any objects(s) between rotating fan blades.

NOTE:
The important precautions, safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness are factors which cannot be built into this product. These factors must be supplied by the person(s) installing, caring for and operating the unit.

TOOLS & MATERIALS REQUIRED

• PHILLIPS SCREWDRIVER
• FLAT SCREWDRIVER
• WRENCH OR PLIERS
• WIRE CUTTERS
• STEP LADDER
• WIRING SUPPLIES AS REQUIRED BY ELECTRICAL CODE
  

UNPACKING YOUR FAN

UNPACK YOUR FAN AND CHECK THE CONTENTS.

• Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged.
• Examine all parts. You should have the following:

PACKAGE CONTENTS

1| Hanging Bracket| CA904566FXX
2| Ceiling Canopy
3| Trim Ring
4| Downrod Assembly| DR94016FXX
5| Motor Cover|
6| Fan Housing with Motor|
7| Fan blade assembly set of 3| BL906460FXX
8| Receiver incl. Wire Nuts| CWT906460
9| Wall Control w/2032 Battery, Cradle A, Wall Pate, Face Plate, Mounting Screws, Cradle B (for flat wall use only)| 980014FWH-R
10| Hardware Bag
Hanging bracket hardware, Safety cable hardware, Blade screws, Blade balancing kit| MH906460

XX=FAN FINISH

NOTE: Design of parts shown above may look slightly different for your specific model of fan.

PREPARATION

PREPARATION:

Verify you have all parts before beginning the installation. Check pulp paper insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original pulp paper insert in motor box.

DO NOT LAY MOTOR HOUSING ON ITS SIDE AS THIS COULD RESULT IN SHIFTING OF MOTOR IN DECORATIVE ENCLOSURE.

INSTALLING THE HANGING BRACKET

CAUTION: To avoid possible electrical shock, be sure electricity is turned off at the main power box before wiring. All wiring must be in accordance with National and Local Electrical Codes and the ceiling fan must be grounded as a precaution against possible electric shock.

1. Locate ceiling joist where fan is to be mounted, being sure location agrees with the requirements in the minimum clearance section of this guide. Wood joists must be sound and of adequate size to support 35 pounds (See page 2, items 3 and 4).

2. If not already present, mount a UL listed outlet box marked “suitable for fan support” following the instructions provided with the outlet box. The outlet box must be able to support a minimum of 35 pounds.

3. Remove canopy from hanger bracket. Remove twist-lock trim ring by rotating counter-clockwise. Remove canopy screw that does not have key slot in canopy. Loosen screw with key slot and remove canopy. (Fig. 1)
   

4. Attach hanging bracket to outlet box using screws provided with the outlet box. (Fig. 2)
   
   

INSTALLING THE BLADES

NOTE:
The blade assemblies must be mounted on the motor assembly so that the “THIS SIDE UP” stamp is visible at the top of the motor.

1. Carefully support fan body (motor) in its packing with the mounting collar (where the wires come out) facing upward.

2. Install a blade assembly to the fan housing by aligning the two screw holes in the blade assembly with the holes in the fan motor , secure with provided screws. (Fig. 1)
   
   

3. Make sure all the screws are firmly tightened.

4. Repeat these steps for the remaining blade assemblies.

5. Attach the motor cover to the fan-motor assembly, then install the screws. (Fig. 2)
   

6. Make sure all the screws are firmly tightened.

HANGING THE FAN

WARNING: Make sure the cross pin is installed well on hanger ball with downrod.

1. Remove hanger ball from downrod by loosening set screw in the side of the hanger ball. Slide hanger ball down and remove cross pin. (Fig. 1)
   

2. Loosen the security set screw from motor collar and remove the downrod pin and cottor pin clip from the downrod. (Fig. 2)
   

3. Carefully feed the electrical lead wires and safety cable from the fan through the downrod. Thread downrod into coupler until holes align. Insert downrod pin through holes in mounting collar and downrod; clip cotter pin through small hole in end of downrod pin to hold downrod in place.

4. Securely tighten set screw against downrod using a large flat-head screwdriver to ensure a tight fit against downrod. Tighten nuts against mounting collar.

5. Slip the trim ring and canopy onto the downrod. (Fig. 3)
   

6. Slide the hanger ball onto the downrod, insert the cross pin through the downrod and tighten. Tighten the set screw.
   NOTE :
   Fan has 6 feet of hook-up wire in case you are using a long extension downrod.

7. Lift ball/downrod/fan into hanger bracket opening.
   NOTE: The tab opposite hanger bracket opening should fit in slot on ball. (Fig. 4)
   

INSTALLATION OF SAFETY CABLE SUPPORT:

Attach the wood screw and the flat washer to the ceiling joist as shown (do not fully tighten). Slide the cable clamp onto the safety cable from the fan. Loop the safety cable around the wood screw that was just attached to ceiling joist. Feed the end of the cable into the clamp and pull as much cable through as possible. Firmly tighten screw in the clamp. Cut off excess cable.

ELECTRICAL CONNECTIONS

REMEMBER – Turn off the power!
NOTE: Control must be installed within 30 feet of fan.
NOTE: For optimal remote performance, keep the WiFi antenna separated from the receiver antenna.
WARNING: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire.
CAUTION: To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch.

1. Insert the receiver into the ceiling mounting bracket with the flat side of the receiver facing the ceiling. (Fig. 1) For best performance, make sure the black antenna and WiFi antenna, on the end of the receiver, remains extended and not tangled with any of the electrical wires. Place the WiFi antenna on the outside of the canopy and stick/fix it on the ceiling
   
   

2. Make wire connections from the fan to the receiver unit. For this step use the bundle of 3 wires on the receiver. (Fig. 3)
   
   Connect the BLUE fan wire to the BLUE receiver wire. Connect the BROWN fan wire to the BROWN receiver wire. Connect the GREY fan neutral wire to the GREY receiver neutral wire.

3. Connect the wiring from the ceiling to the receiver unit. (Use the 2 wire bundle on the receiver.) Secure with supplied wire nuts. Connect the BLACK building supply wire to the BLACK receiver wire.
   Connect the WHITE receiver neutral wire to the WHITE building neutral wire. Connect the COPPER building ground wire to the 2 GREEN ground wires from the fan.

FINISHING THE INSTALLATION

1. Align the locking slots of the ceiling canopy with the two screws in the mounting plate. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly.
2. Install the remaining two mounting screws into the holes in the canopy and tighten firmly.
3. Install the trim ring by aligning the ring’s slots with the screws in the canopy. Rotate the trim ring clockwise to lock in place.
   

WARNING:
Make sure the hook on the hanging bracket properly sits in the groove in the hanger ball before attaching the canopy to the bracket by turning the housing until it drops into place.

INSTALLING THE WALL CONTROL

REMEMBER to turn off the power before you begin.
NOTE : 1. Control must be installed within 30 feet of fan. 2. Secures to any surface or application: flat wall, single gang box, multi gang box

Option 1. Flat Surface Installation

1. Select a desired location. Use the wall plate to mark the location of the mounting holes. Plastic wall anchors or mounting screws are needed for this application. (Fig. 1)
   
   HIRO Control System

2. Seat the cradle B into the wall plate. Secure the wall plate to the wall using the provided hardware.

3. Snap the face plate cover onto the wall bracket.

4. Remote transmitter will be held in place with built in magnets.

Option 2. For Single Gang Box

1. Remove the existing wall plate and the old switch from the wall outlet box.
2. Seat the cradle A into the wall plate. (Fig. 2)
3. Connect the black lead wires from the switch in the cradle A to the black wires in the switch box. Hot input wire to one of the cradle A switch leads. Power lead to the fan is connected to the remaining switch lead.
4. Connect the wall plate / cradle A assembly to the wall outlet box using the supplied hardware.
5. Snap the face plate cover onto the wall bracket.
6. Remote transmitter will be held in place with built in magnets.
   

Option 3. For Multi-Gang Wall Switch Box

1. Remove the existing wall plate and old switch from the wall outlet box. (Fig. 3)
   
   HIRO Control System

2. Connect the black lead wires from the switch in cradle A to the black wires in the switch box. Hot input wire to one of the cradle switch leads. Power lead to the fan is connected to the remaining switch lead. (Fig. 4)
   

3. Attach cradle A to the wall switch box using supplied hardware.

4. Attach the multi-gang face plate (not included) to the switch set in the wall outlet box. Cradle A Hinkley switch will fit in any standard decora outlet face plate.

OPERATION

Your DC brush less motor is equipped with an automatically learned type remote control. There is no frequency switches on the receiver or transmitter. The fan is ready to use once the pairing process is done.
Remove the panel from the transmitter and then install one 2032 battery (included). You need to use a coin to open or close the battery cover. To prevent damage to transmitter, remove the battery if not use for long periods of time (Fig. 1)

WARNING: Chemical Burn Hazard. Keep batteries away from children.

This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely  secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. IF you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

The batteries shall be disposed of properly, including keeping them away from children; Even used cells may cause injury.

1. button:
   Press this button to turn the fan on/off.

2. button:
   Press this button to set fan wind direction up or down.

3. button:
   Press this button to turn fan speed higher or lower

4. Signal light (Fig. 2)
   

Summer Mode and Winter Mode Operation

IMPORTANT: To operate the reverse function on this fan, press the reverse button while the fan is running.

Summer Mode (forward):
A DOWNWARD airflow creates a cooling effect as shown in Figure 3. This allows you to set your air conditioner on a warmer setting without affecting your comfort.

Winter Mode (Reverse):

An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler setting without affecting your comfort.

CARE AND CLEANING

Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound during operation. This is especially true in climates with broad temperature and humidity ranges.

When dusting the blades, you must support the blade to prevent bending – no pressure should be applied to the blades. If you experience any flaws in the operation of your fan, please check the following points.

TROUBLESHOOTING

CAUTION:
Switch off power supply before carrying out any of these checks.

PROBLEM

Fan Will Not Start

1. Check to assure that a new battery is installed in the remote control or wall control .Check main and branch circuit breakers and /or fuses
2. Check line wire connections to fan housing wiring. Make sure forward/reverse switch is set to one or the other position, not stuck in between.
3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency.

Fan Sounds Noisy

1. Check and make sure that all screws in motor housing are snug (but not over tight).
2. Check that the screws securing blade arms to the motor are tight.
3. Check that wire connectors in switch housing are not rattling against each other or the interior wall of the switch housing.
4. Check that all glassware is finger tight and that bulb(s) are well held in the sockets, if a light kit is used.
5. Check that the canopy is firmly attached to hanging bracket and not vibrating against ceiling.

Fan Wobbles

1. Check that all blades are firmly screwed into blade arms. Check that all blade arms are firmly secure to the motor.
2. Check to make sure that light kit (if present) is firmly attached to switch housing and that all glassware and shades are fastened properly. Wobble can also result from even the smallest deviations in distance from blade tip to blade tip.
3. If measurements from blade tip to blade tip are not equal, loosen screws connecting blade to blade arm one at a time and adjust blade(s) so that distances are equal.
4. Interchanging adjacent blades may redistribute mass and result in smoother operation. Blade arms can be bent slightly to restore same pitch to all blades if a blade is different than the other blades when viewed edge on.
5. Most wobble can be traced to a loose electrical box or mounting bracket. Make sure these are tight and the ball is completely seated in the bracket.
6. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable
   WARNING: To reduce the risk of personal injury, do not bend the blade arm while installing, balancing the blades, or cleaning the fan. Do not insert foreign objects between rotating fan blades.

Remote Control Malfunction.

1. Do not connect the fan with a wall mounted variable speed control(s).
2. Make sure the dip switches are set correctly.

DOWNLOADING THE HINKLEY APP

HINKLEY SMART FAN OPTIONS:

In addition to the included wall control, you can control your Hinkley fan through the Hinkley app.

• To use the Hinkley app, download it for free from the App Store or Google Play.
• Open the Hinkley app where you will be prompted to create an account.
• Enter all necessary information to create an account.
• After account is created you will receive a verification code email to finish setting up the Hinkley app (Check spam folder if email is not received).
• Confirm Bluetooth is enabled to allow the fan and Hinkley app to connect to each other.
• Click add a device on the home screen and select desired fan.
• The Hinkley app will then have you enter in WiFi name and password.
• Click done on the Hinkley app to complete connecting the fan.
• The Hinkley app will have options on the main screen for fan speeds, dimming and setting timers.
• Scan the QR code below for more information on the Hinkley app operation.
  SCAN FOR ADDITIONAL DETAILS
  

HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT, PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE COMMITTED TO DESIGN, PERFORMANCE AND QUALITY, AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US.

Customer Support

FOR A COMPLETE ASSORTMENT OF OUR PRODUCTS AND SOURCE BOOKS, VISIT HINKLEY.COM.

GLOBAL HEADQUARTERS
33000 Pin Oak Parkway I Avon Lake, Ohio 44012
T (440) 653 5500 F (440) 653 5555 hinkley.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>