HANDY HEATER YL-01 Portable Wall Plug Space Heater User Manual
- June 14, 2024
- HANDY HEATER
Table of Contents
HANDY HEATER YL-01 Portable Wall Plug Space Heater
Overview
Important
- Please save this user manual
- Only Designed for wall socket
- Please read and understand this entire manual before attempting to operate or install the product.
Operation Instructions
- Plug the product into the required 220v power outlet. Most convenient to plug into the wall using the “Plug Rotation Button”. (See Setting Orientation Adjustment).
- Press the”< >” button to tum on the heater.
- Use the “+” button to increase the temperature, or use the “-” button to decrease the temperature; the screen displays the temperature between 15-32 degrees.
- When finished, press the”< >” button and unplug the product from the electrical outlet. Store in a cool dry place until next use.
Note: If the room temperature reaches the set temperature, the heater will be turned off and the machine will enter standby mode, when the room temperature drops below the set temperature, the heater will restart and operate normally. To reduce heating interruptions, set the temperature to a maximum of 32 degrees.
Plug Direction Adjustment
1. Press and hold the “plug rotation button”
2. Using your hands, gently turn the plug to the desired position as shown in
the picture below.
3. Release the “Plug Rotation Button” to lock in place. NOTE: Press
button to release.
Timer Function
The product has a built-in timer that automatically turns off the unit after a set time.
1. When plugging in and turning on the product, press the “ ” button to
activate the timer as shown.
2. Press the “ ” button repeatedly to set the number of hours before the wall
plug heater turns off. You can choose between 1-12 hours.
3. Once the desired number of hours has been selected, stop pressing the “ ”
button.
4. To cancel the timer, turn off the product directly.
Important Safety Instructions
- Please read all instructions before using this healer.
- When using electrical appliances, basic precautions should always be followed to reduce fire, electric shock, and personal injury risks, including the following:
- This healer must be plugged into its own 220V, 15A (or greater) circuit. Do not plug anything else into the same circuit. If you are unsure whether your home meets this code, consult a certified electrician before using it. Failure to observe may result in fire, overheating, malfunction, property damage, personal injury or even death!
- Only connect to the correct outlet. Do not connect the heater to an outlet where extension cords, surge protectors, timers, direct circuit breakers, or other devices are connected to the same outlet. Failure to observe may result in fire, overheating, malfunction, property damage, personal injury or even death!
- This heater is hot when in use. To avoid burns, keep bare skin away from hot surfaces.
- Keep flammable materials, such as furniture, pillows, bedding, paper, clothing, and drapes, at least 3 feet (0.9 m) away from the front of the heater and away from the sides and rear of the heater.
- Extra caution must be exercised when any heater is used by or near children, persons with disabilities, pets, or when the heater is left unattended.
- Always unplug the heater when not in use.
- Do not continue to operate the heater if the plug is damaged or if the heater has malfunctioned, been dropped, or damaged in any way. Discard the heater, or contact a qualified service technician for inspection and/or repair.
- Do not use outdoors. Exposure to outdoor elements such as rain, snow, sun, wind, or extreme temperatures can make a heater a safety hazard.
- Do not use in a humid environment, to avoid short circuits caused by water ingress.
- Do not use the heater where ii may fall into the water.
- To disconnect the heater, first turn the power button to the off position, then remove it from the wall outlet.
- Do not allow foreign objects to enter or block any ventilation or exhaust openings as this may result in electrical shock, fire, or damage to the heater.
- To prevent a possible fire, do not block air intake or exhaust openings in any way. Do not use it on soft surfaces such as beds as the vents may become blocked.
- Leave at least 3 feet of unobstructed clearance in the front, rear, or sides of the heater for maximum heat, air, and ventilation flow.
- Hot arcing or sparking parts inside the healer. Do not use the heater in areas where gasoline, paint, or flammable liquids are used or stored, and do not use flammable solvents to clean the heater. Always keep the heater dry.
- Use this heater only as directed in this manual. Any other use not recommended by the manufacturer may result in fire, electric shock, or personal injury.
Care and Maintenance
WARNING: Before starting any maintenance, unplug and allow the heater to cool completely.
- To clean, wipe the exterior with a damp, non-abrasive cloth. Use mild soap if needed. Wipe dry with a soft cloth.
- CAUTION: Do not allow liquids to enter the heater.
- Never use alcohol, gasoline, abrasive powders, furniture polish, or harsh brushes to clean heating heater, which may cause damage to the heater casing.
- Never immerse the hand heater in water.
- Wait until the device is completely dry before using it. Store in a cool, dry place when not in use.
- WARNING: To reduce the risk of fire or electric shock, do not use this unit with other equipment; don’t use it with extension cords.
- WARNING: Potential electrical hazard if not followed.
Specification
- Product voltage : 220 V(60 Hz)
- Product power : 800w
- Product Dimensions: 5.53″(W) X 4.93″(D) X 3.5″(H)
- Unit Weight: 0.89 lbs