sentiotec A-910 Sauna Light Instruction Manual

A-910
max. 60 W / IP54
INSTRUCTIONS FOR INSTALLATION AND USE

Version 08/23

About this instruction manual

Carefully read these instructions for installation and use, and keep them near the sauna. This ensures that you can refer to information about your safety and the operation at any time.
These installation and operating instructions can also be found in the downloads section of our website: www.sentiotec.com/downloads.

Symbols used for warning notices
In these instructions for installation and use, a warning notice located next to an activity indicates that this activity poses a risk. Always observe the warning notices. This prevents damage to property and injuries, which in the worst case may be fatal.
The warning notices contain keywords, which have the following meanings:

CAUTION!
Minor injuries can occur if this warning notice is not observed.
Other symbols
This symbol indicates tips and useful information.

1.1. Safety information for the installer

• Installation may only be performed by a qualified electrician or similarly qualified person.

• Use otherwise than as intended can constitute a fire risk!

• Children should be supervised to ensure they do not play with the device.

• Commissioning is strictly prohibited if the light is damaged.

• The light may only be operated outside of the packaging.

• The light will become hot during operation. The external lamp housing will also become hot. Do not touch the light with bare hands during operation.

• The product as a whole may not be modified or converted.
  Modifications to the light invalidate the guarantee.

• If particular problems occur which are not dealt with in sufficient detail in these instructions for use, please consult your supplier for your own safety.

Installation and connection

Before commissioning the light, ensure that it has not been damaged in transit.

WARNING!

• The light must not be operated if it is damaged.
• The sauna lamp may only be installed and connected when the power supply is disconnected.

2.1. Installation
Keep the lamp housing in the desired installation position and mark the boreholes.
Use appropriate screws to secure the light.
Ensure that no cables are damaged.
Conduct the power supply leads through the aperture of the lamp housing. Ensure that the lead is cleanly and tightly conducted through the seal.
Now connect the connection cables of the domestic electrical installation to the screw terminals of the light. First connect the green-yellow earth wire and then the two other wires. As a rule, the brown (or black) cable is the live wire, connect this to the terminal  marked with ‘L’. The blue conductor must be connected to the terminal marked with ‘N’.
Do not kink the cable; please ensure that the cable and plug are free from attractive and torsional forces.
Protect all cables and insulations from possible damage.

Install the bulb (see 3.1. Changing the bulb on page 5).
The rating plate must not be removed.

Operation

3.1. Changing the bulb
Only use max. 60 W, E 27 type bulbs. Use of other bulbs can lead to overheating.
The power supply must be disconnected before changing the bulb.
If the bulb is changed directly after failure, you must first leave the bulb to cool down for a sufficient period.
Remove the protective cover and the protective glass.
Carefully unscrew the defective bulb from the socket.
Carefully insert new bulb into the socket. Do not use force or excessive pressure.
Before commissioning, check that the bulb is properly positioned in the socket. Replace the protective glass and protective cover.
When assembling ensure the correct position of the seal between the lamp housing and the protective glass.

Cleaning and maintenance

Before cleaning you must ensure that the light is disconnected from the power supply.
Use a dry or slightly moistened cloth for cleaning.
Never clean with chemicals or abrasive cleaners.

Disposal

• **** Dispose of packaging materials in accordance with the applicable waste disposal regulations.
• Used devices contain reusable materials as well as hazardous substances.
  Therefore, do not dispose of your used device with household waste, but do so in accordance with the locally applicable regulations.

Technical data

NOTE
……………………………………………………
…………………………………………………….
……………………………………………………..

CENTRAL EUROPE semeiotic GmbH Division of Harvia Group
Wartenburger Straße 31, A-4840 Vöcklabruck
T +43 (0) 7672/22 900-50  F -80
info@sentiotec.com
www.sentiotec.com| GLOBAL HARVIA
P.O. Box 12, Teollisuustie 1-7, 40951 Muurame, FINLAND
T +358 207 464 000
harvia@harvia.fi
www.harvia.fi
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>