Zehnder ITV050874 Brand RF Repeater User Manual

Zehnder ITV050874 Brand RF Repeater

Product Information

• The Zehnder RF Repeater is a device used to extend the range of wireless communication between Zehnder ventilation devices and RF controls and sensors.
• It operates at a frequency of 925MHz and is designed to relay messages sent on the configured network.
• The RF Repeater can be paired with ventilation units to enhance their functionality and provide comfortable indoor ventilation.
• It can also be paired with new RF controls and sensors for added convenience.
• This installation manual contains all the necessary information for the safe and correct installation of the RF Repeater.
• It is important to read and understand this manual before use to prevent personal injury or damage to property.

Product Usage Instructions

1. Unpack and prepare the installation:
   • Check that the packaging is not damaged.
   • Check that the parts are not damaged.
   • Check that the contents of the package are complete.
   • Verify that the correct RF Repeater (925MHz variant) has been supplied based on the identification plate.
2. Gather the following tools and mounting materials:
   • Screwdriver with a bit or screw head of type PH2.
   • Drill with a drill diameter of 6mm.
3. Pair RF Repeater with a ventilation unit:
4. Start pairing mode on the ventilation unit.
5. Activate bright mode on the RF Repeater.
6. Connect with the RF Repeater.
7. If the status LED blinks 3x GREEN, the pairing is successful. If it blinks 3x RED, the pairing has failed.
8. Pair the RF Repeater with a new RF control and sensor:
9. Activate pairing mode on the RF Repeater.
10. Connect a new RF control/sensor.
11. If the status LED blinks 3x GREEN, the pairing is successful. If it blinks 3x RED, the pairing has failed.

If you have any questions or need assistance, contact your Zehnder agent. The contact details can be found on the back of this installation manual.

Quick Reference

Foreword

• Read this manual carefully before use.
• This installation manual contains all the information required for the safe and correct installation of this RF Repeater. Get to know the system to prevent personal injury or damage to property.

Questions

• For any questions, contact your Zehnder agent.
• The contact details are given on the back of this installation manual.
• The RF Repeater is regularly subject to new developments and improvements.
• As a result, the operation of the system might deviate from the description in this manual. In that case, an up-to-date installation manual can be downloaded online or ordered from your Zehnder agent.

All rights reserved

• This installation manual has beencompiled with the utmost care.
• However, the publisher cannot be held responsible for any damage causedby failure to follow safety or operating instructions.
• In the event of disputes, the Dutch text takes precedence.

Reading guide

• The following symbols are used in this installation manual to draw the reader’s attention to safety aspects and important information:

This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Unpacking and preparing the installation

Contents of the box

Checking the delivery

1. Check that the packaging is not damaged.
2. Check that the parts are not damaged.
3. Check that the contents of the package are complete.
4. Based on the identification plate, check that the correct RF Repeater has been supplied (925MHz variant).

Please report any damage, missing parts, or incorrect delivery based on the identification plate on the back of the RF Repeater (Figure 1.2) directly to your Zehnder agent. The contact details are given on the back of this installation manual.

Tools and mounting materials required

• Screwdriver, equipped with a bit or screw head of type PH2
• Drill, with a drill diameter of 6mm.

Description and identification

General

• Zehnder ventilation devices can be operated remotely using wireless switches.
• These systems can also provide ventilation based on CO2 concentrations measured using wireless sensors.
• This wireless communication runs via RF at 925MHz.
• The range of RF is limited. It can be increased using the RF Repeater.
• The RF Repeater relays the messages sent on the configured network.

Combination options

• The RF Repeater can be combined with all Zehnder RF controls and sensors.
• The ComfoAir 160/200/350/550 and ComfoAir Standard cannot be paired in the Assistant Mode.
• The Easy RF and the Chrono RF cannot be paired in the Assistant Mode.
• Consult your Zehnder agent for the recommended combinations with other Zehnder RF controls and sensors.

Safety

Safety regarding mounting and installation

• Dangerous electrical voltage! Risk of death or injury due to 120 V electrical voltage.
  • Work on the 120 V mains must only be carried out by qualified electricians.
  • Disconnect the device from the power supply before starting to mount or dismount it.
  • Only use undamaged connection cables.
  • Keep the device away from water and humid environments.
• Keep children and animals away from the mounting location during installation.
• The RF Repeater may only be mounted as described in this installation manual.
• Always follow the local safety regulations when mounting the device.
• Check the device for damage caused by transport.
• Check that the mains voltage corresponds to the local mains voltage.
• If the power cord is damaged, it must be replaced with the original cord by the manufacturer, its service representative, or similarly qualified persons in order to avoid accidents.
• If the power adapter is damaged, it must be replaced with the original from the manufacturer.

Mounting instructions

• Never mount the RF Repeater in wet rooms, such as bathrooms and toilets. Excessive humidity can damage the device.
• Mount the RF Repeater in a frost-free environment.
• Never place the RF Repeater near large metal objects or devices that transmit wireless signals or cause electromagnetic interference (EMI).
• This may disrupt the signal between the RF Repeater and the ventilation unit.
• An incorrect connection can damage the operation.
• Only use suitable tools to install the RF Repeater.
• Do not overtighten screws.
• We recommend mounting the RF Repeater between 36 and 59 inches above the floor so that it is visible and easy to operate.
• Do not mount the RF Repeater higher than 79 inches from the floor.
• The RF Repeater works on a 120V-60Hz adapter. It should therefore be installed in a location with a wall socket.
• Mount the RF Repeater without opening the housing (see Mounting section).

Warranty

Zehnder offers a 24-month warranty on this device. This period applies from the date of installation up to a maximum of 30 months after the production date of the device.

The warranty is void if:

• a defect is the result of inadvertent or bcareless use of the device;
• a defect is the result of contamination of the device;
• parts from another manufacturer have been used;
• repairs have been carried out by unauthorised persons.

The warranty does not cover:

• costs for disassembly and assembly on site;
• wear and tear from normal use.

Mounting

View of the components

Mounting the RF Repeater

All letters in this section refer to the previous images.

1. Determine the mounting location in relation to the wall socket to be used. There must be no mechanical stress on the cable.
2. Drill the two holes as shown in Figure 4.1 at a distance of 1 3/4 inches. The ‘Mounting Template’ at the end of this manual can be used for this.
3. Attach the rawl plugs and screws included in the package.
4. Fix the RF Repeater as shown in Figure 4.1.
5. Connect the RF Repeater to the wall socket using the USB cable and USB adapter supplied.
   • It is not necessary to open the RF Repeater for mounting. To avoid ESD damage, do not open the RF Repeater.

Commissioning

Conditions for the proper functioning of the RF Repeater

• RF pairing with a ventilation unit only works when the RF Repeater is within range of the unit.
• Up to 5 RF Repeaters can be used in a single network.
• If the RF Repeater is accidentally put into pairing mode, it can simply be canceled.
• This has no consequences for the existing network.

Operation

Figure 5.1 – Front of RF Repeater

1. Press the control button briefly (<5s) to activate or deactivate the bright mode.
2. Depress (>5s) the operating button to activate or deactivate pairing mode.
   • When the bright mode is activated, it remains active for 15 minutes. The bright mode is also active in pairing mode.
   • When the pairing mode is activated, it remains active for 10 minutes.

Pairing mode
The pairing mode for the RF Repeater can be used to connect the RF Repeater to a new RF network or an existing RF network

Connecting to a new RF network:

• Set the ventilation unit in pairing mode
• Set the RF Repeater in pairing mode

The RF Repeater will receive the same address as the ventilation unit and can now be used as an assistant for connecting other RF controls and sensors, see Assistant Mode. To connect the RF Repeater to an existing RF network, follow the same steps. No further changes to the network are required. The RF Repeater will immediately relay all RF communications on the network.

Assistant Mode

Connecting new RF controls and sensors to the system:

• Set the RF Repeater in pairing mode
• Set the new RF control/sensor in pairing mode
  • If pairing mode is first selected on a new RF controller/sensor and then on the RF Repeater, it will be canceled.
  • Some RF controls or sensors have the option to connect with a random RF address or with the RF address of the respective control/sensor.
  • This is not possible via the RF Repeater.
  • If this option is desired, it must be done directly via the ventilation unit.
  • Then all other controls/sensors must be connected again.

Indication

• The power LED lights up green when the RF Repeater is supplied with power.
• The RF LED flashes green when an RF signal is detected on the same frequency as that used by the Zehnder RF system to communicate.
• During normal operation, the status LED flashes yellow when an RF signal is received and relayed.
• During pairing mode, the status LED flashes blue to indicate that the RF Repeater is searching for another device to connect to.
• If the connection is successful, the status LED flashes green 3 times. If the connection fails, the status LED flashes red 3 times.

Malfunctions

Malfunctions of the RF Repeater

Connect power and/or check cabling and plug.
The RF LED lights up continually.| There is too much local RF communication, causing disruption to the system.| Try to find out where the disturbance is coming from and solve it.
The status LED continually flashes red.| There is a problem with the RF receiver.| Replace the RF Repeater.

In the event of recurring malfunctions, please contact your Zehnder agent.

Unsafe situations

the power.

2.  Remove the RF Repeater from the wall.

3.  Dry all parts.

| If the RF Repeater is damaged, please

contact your Zehnder agent.

Maintenance

Regularly remove dust with a dry duster or very carefully with a vacuum cleaner.

• Never clean the device with water.
• Never use cleaning agents.

Dismounting and disposal

• If the RF Repeater is dismounted, the current disposal regulations applicable to the location must be observed.
• Dispose of the RF Repeater in an environmentally friendly way.
• Do not dispose of the device together with household waste.
• The RF Repeater can be disposed of at an electronic waste collection point.
• It is the responsibility of the owner of the RF Repeater to dispose of the device in a responsible manner.

Changes or modifications not expressly approved by Zehnder could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 155 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information

• RF Repeater
• Zehnder America
• 6 Merrill Industrial Drive, Suite 7
• Hampton, NH 03842 USA
• 603 601 8544
• www.zehnderamerica.com.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Mounting Template

References

• Zehnder HRVs and ERVs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>