INVISION MX150 PC Monitor Arm Ergonomic Height Adjustable Gas Assisted User Manual

INVISION MX150 PC Monitor Arm Ergonomic Height Adjustable Gas Assisted

VESA Compliance 75x75mm & 100x100mm
Recommended Screen Sizes 17″ – 27″
Integrated Cable Management
Load Capacity 2 – 6.5kg (4.4 – 14.3lbs)
To receive large format PDF instructions please email: help@invisiontvbrackets.com.

Parts List

Tools List:

Important: Please be extra cautious when removing the velcro strap – the monitor arm is spring loaded and packaged under tension. This can open out with force when released.
KEEP AWAY FROM FACE!

1. Check the box contains all the items in the Parts List.
2. Check the screens VESA measurements and monitor weight.
3. Please read the instructions fully and plan how to mount your monitor.
4. You may need additional tools: A drill will only be needed if you are bolting it through a desk, the screwdriver is used for removing the cable management.

WARNING

Severe personal injury and property damage can result from improper installation or assembly. Please read the following warning carefully before beginning.

• If you do not understand the instructions or have any concerns or questions please contact us or a competent installer.
• Do not install or assemble if the product or hardware is damaged or missing. If you require replacement parts, please contact us at invision for assistance
• This product fits most VESA compliant 17-27* LCD/monitors to a maximum weight of 6.5kg (14,3 b)
• Do not use this product for other than the orginal design purpose
• This product contains moving parts, please use with caution
• When instaling montor take care not to damage electrical wining or power source important – mains and data cables must be free trom twisting and/or shearing
• The manufacturer disclaims any liabilty for the modifications, improper installation or installabon over the specifed weight range. The manufacturer will not be liable for any damages ansing from the use of, or inabilty to use the product
• This product is designed for indoor use only, use of this product outdoors could lead to product failure and severe personal injury
• This product contains a high pressure gas spring. This mechanism is not user serviceable and any interference could result in injury or damage. Please dispose of with caution. in order to ensure the pertormance of the gas spring it is recommended to fully extend the arm several tmes per month

INSTALLATION INSTRUCTION

Step 1 – Cable Management
Tip – Run cables first (depending on rear of desk accessibility)

1. Remove cable management trays from both arms by removing bolts from lower cable trays see diagram ‘A’ and ‘B’ below.
2. Run cables needed for PC monitor or TV into the cable trays making sure they slide within the trays easily and ensuring they do not become trapped or twisted.
3. Clip in and re-attach cable management trays using removed bolts.
4. Perform a safety check ensuring cables do not get trapped when the monitor arm is being moved.

Step 2 – Desk Clamp Installation (See Pg 3 – Step 3 for Through-the-Desk Installation)

1. Unpack the clamp ‘G’ and wind out fastening knob ‘H’ fully to allow easy access with Allen key to base assembly bolts part ‘C’ (see diagram ‘A*).
2. Secure the clamp to base using bolts ‘C’ and tighten with Allen key ‘F’ [4mm] (see diagram ‘A’).
3. If required for thicker desks please adjust the clamp assembly height part ‘G’ with Allen key ‘F’ [5mm] (see diagram ‘A’).
4. Secure clamp ‘G’ to the desk by winding in knob ‘H’ fully and then tighten up [Do NOT overtighten] (see diagram ‘B’).
   Please Note: Do not adjust inner central bolt which secures lower monitor arm to inside of base, this is pre-set so the arm swivels 270 degrees at its base.

Step 3 – Through-the-Desk Installation
Please Note: Many desks are pre-drilled for this application. If not a 10mm hole will need to be drilled through the desk where you require the monitor arm base to be fixed.

1. Insert bolt part ‘D’ through metal plate part ‘F’ and fix plate to arm base using bolts ‘C’ (see diagram ‘A’).
2. The bob as square neckal tocks in pite bot test um win being the diapa 4).
3. Once attached to arm pass bolt ‘D’ through pre-drilled desk hole and securely fasten using wing nut and plate ‘D’ and ‘E’ (see diagram ‘B’).

Mounting the Monitor

1. Check monitor or TVs VESA by measuring the distance between the mounting holes on the back of the screen – this is where bolts A/B will fit.
2. Screw 2 bolts into the top two holes on the back of the monitor using bolts A/B and tighten in 3 turns leaving room between the bolt head and rear of screen for hanging (see diagram ‘A’).
3. Carefully lift monitor and hang onto the monitor arms VESA plate (see diagram ‘B’).
4. Fit the bottom 2 bolts into the VESA plate and tighten all the bolts (see diagram ‘C’).
   Please Note: Set the torque of arm if screen moves down too easily (see Step 5)

Using Your Invision MX150 Ergonomic Monitor Arm
Setting the dynamic elevation torque of the monitor arm:

1. Once fitted the screen should raise or lower with gentle pressure and stay at the desired height.
2. If the screen moves upwards of its own accord then adjust the torque using the 5mm Allen key ‘F’ and wind the set screw in minus direction.
3. If the screen moves downwards of its own accord then adjust using the 5mm Allen key ‘F’ and wind the set screw to plus direction.

Adjusting the Tilt Angle

1. The screen tilt can be set to your desired viewing angle by simply moving the screen backwards and forwards by hand. If you find the screen moves forward off its own accord, the tilt adjustment tension can be tighten using the Allen key ‘F’ (see diagram).

Rotational Features

1. Your monitor arm allows you to rotate your screen through 360 degrees to view in portrait mode or landscape mode providing the VESA mount on your screen is central.
   Please Note: Beware of trapping or breaking cables when rotating monitor DO NOT ROTATE MORE THAN 90 DEGREES IN EACH MOTION

To activate your 3 year warranty please email your name and product ref MX150 to warranty@invisiontvbrackets.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>