HT50 Holyton Drone with Camera Instructions
- June 14, 2024
- Holyton
Table of Contents
HT50 Holyton Drone with Camera
Product Information
The product is a drone model HT50 manufactured by Holyton. It
comes with various features and functions, including Altitude-Hold
Function and Optical Flow Positioning. The package contents include
the drone, transmitter, drone battery, propellers, USB charging
cable, screwdriver, and instructions for use. The drone is equipped
with a HD camera and indicator lights. The transmitter has a phone
holder, power switch, joysticks for controlling the drone’s
movement, and a return to home function.
Product Usage Instructions
Before using the drone, it is important to follow the safety
guidelines and check the flight environment:
-
Fly in open areas.
-
Keep the drone in sight while flying.
-
Fly below 394 feet (120m).
-
Avoid flying over or near obstacles, crowds, high voltage power
lines, trees, airports, or bodies of water. -
Avoid flying near strong electromagnetic sources.
-
Do not use the drone in adverse weather conditions like rain,
snow, fog, and wind.
For operation requirements:
- Follow the instructions for using the battery.
- Dispose of waste lithium-polymer batteries properly by
contacting local environmental or waste agencies, the supplier, or
a Li-Po battery recycling center.
For maintenance, refer to the maintenance section of the user
manual.
To operate the drone, follow these steps:
-
Charge the drone and transmitter using a USB adapter (5V/2A)
and the provided USB charging cable. Charging time is approximately
220 minutes for the drone and 60 minutes for the transmitter. -
Ensure the drone battery is fully charged before flight.
-
Turn on the transmitter by using the power switch.
-
If using MODE 2 (default setting), use the left joystick to
ascend, descend, fly forward, fly backward, and rotate left or
right. Use the right joystick to control speed, fly left or right,
and return to home. -
If using MODE 1, turn on the transmitter while holding the
Record Video button to enter MODE 1. Use the left joystick for
forward, backward, ascend, and descend movements. Use the right
joystick for rotate left or right and fly left or right. -
Follow the instructions provided in the user manual for
additional functions such as Altitude-Hold and Optical Flow
Positioning.
Always remember to fly the drone in a safe and responsible
manner, following all applicable laws and regulations.
Instructions For Use Gebrauchsanweisung
V 2.0
HT50
holyton@foxmail.com (USA) holyton_eu@foxmail.com (EU) holyton_ca@foxmail.com
(CA)
English Deutsch
01-41 42-79
Contents
Disclaimer & Warning ……………………………………………………………………….. 01 Safety Guidelines
……………………………………………………………………………….. 01 Maintenance
………………………………………………………………………………………. 05 Package Contents
……………………………………………………………………………… 06 Drone Details
……………………………………………………………………………………… 07 Transmitter Details
…………………………………………………………………………….. 08 Joystick
Mode……………………………………………………………………………………… 09 Preparation Before Flight
Charging ……………………………………………………………………………………….. 10 Download APP
…………………………………………………………………………….. 11 Gimbal Cover
……………………………………………………………………………….. 11 Drone Battery
………………………………………………………………………………. 12 Arm ………………………………………………………………………………………………..
13 TF Card ………………………………………………………………………………………….. 13 Propellers
……………………………………………………………………………………… 14 Foldable Handle/Phone
Holder…………………………………………………… 14 Antenna …………………………………………………………………………………………. 15
Flight Pairing …………………………………………………………………………………………. 16 Connect to Wi-Fi
………………………………………………………………………… 17 Calibrating the Compass
………………………………………………………….. 18 GPS Searching ……………………………………………………………………………. 19
Calibrating the Gyro ………………………………………………………………….. 20 Takeoff/Landing
………………………………………………………………………… 20
Functions Details
Emergency Stop …………………………………………………………………………….. 21 Speed Switch
………………………………………………………………………………….. 21 Take Photo/Record
Video……………………………………………………………… 22 Camera Angle Adjustment
…………………………………………………………… 22 Headless Mode ……………………………………………………………………………….. 23
Return to Home (RTH) …………………………………………………………………… 24 Stabilization Function
Altitude-Hold Function ………………………………………………………………….. 27 Optical Flow Positioning
……………………………………………………………….. 27 APP Operation Instruction
Operation Interface…………………………………………………………………………. 30 Beginner
Mode………………………………………………………………………………… 32 Specifications
………………………………………………………………………………………. 33 Contact Us
…………………………………………………………………………………………… 35 General Information
…………………………………………………………………………… 36
DISCLAIMER & WARNING
1. Please read this Disclaimer & Warning and Safety Guidelines carefully
before using our product. This product is not recommended for people under the
age of 14. By using this product, you hereby agree to this disclaimer and
signify that you have read it fully. You agree that you are responsible for
your own conduct and any damage caused while using this product, and any
consequence. You agree to only use this product for it’s designed purposes and
in accordance with the local laws, regulations and all applicable policies and
guidelines that Holyton may provide. 2. When using this product, please be
sure to strictlyabide by the specification requirements and safety guidelines
stated in this document. Any personal injury, property damage, legal disputes
and all other adverse events caused by the violation of any of the safety
instructions or due to any other factor, WILL NOT be Holyton’s responsibility.
SAFETY GUIDELINES
CHECK BEFORE USE
æThis product is a high precision drone that integrates various electronic
stability and control mechanisms. Please be sure to configure this drone
carefully and correctly to ensure safe, accident-free operation çEnsure that
the batteries of the drone and transmitter are clean, undamaged, and fully
charged before every use. èEnsure that all the propellers are undamaged and
are installed in the correct orientation.
-01-
SAFETY GUIDELINES
é Please perform a thorough check of the product before each use. Inspectthe
integrityof the parts, any signs of cracksand wear offon the propellers,
battery power and effectiveness of the indicator, etc. If there is any problem
found after checking the drone, please refrain from using it until the problem
is resolved.
FLIGHT ENVIRONMENT
Fly in Open Areas
Keep in Sight
Fly Below 394 feet (120m)
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
Avoid flying over or near obstacles, crowds, high voltage power lines, trees,
airports, or bodies of water. DO NOT fly near strong electromagnetic sources
such as power lines and base stations as it may affect the onboard compass.
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
DO NOT use this drone in adverse weather conditions like rain, snow, fog, and
wind.
-02-
SAFETY GUIDELINES
OPERATION REQUIREMENTS
æ DO NOT use this product to follow any moving vehicles. ç During the flight,
turn off the motors only in an emergency. è When the battery runs low, return
the drone back to your starting point. é DO NOT use this product if you feel
tired, take medicine or feel unwell and drink alcohol. ê Be aware of the
volume of noise that the drone produces. Please ensure to keep your distance
to avoid ear damage.
ë Stay away from the rotating propellers and motors.
ìDO NOT fly in any spaces where drones are prohibited. Please respect people’s right to privacy by not flying your drone close to others.
USE OF BATTERY
æ Please ensure batteries are fitted in the correct orientation as shown in
the instruction manual. ç Avoid short circuits by fitting the batteries
correctly, and do not crush or squeeze the batteries as this could cause the
risk of a fire or explosion. è DO NOT mix new and old batteries as this can
lead to poor performance of the product. é Please dispose of used batteries
carefully, do not litter, and recycle where ever possible. ê DO NOT expose
dead batteries to heat or fire, or they may explode.
-03-
SAFETY GUIDELINES
ë If the device is not going to be used for an extended period of time, please
remove batteries to prevent potential damage to the drone from battery
leakage. ì Only use the USB charging cable that comes with the drone to charge
the battery. í DO NOT connect the battery directly to wall outlets or car
cigarette -lighter sockets as this will damage your battery since they have
different voltages. î DO NOT attempt to disassemble or modify the battery in
any way. ï DO NOT use the battery if it gives off an odor, generates heat,
becomes discolored, deformed, or appears abnormal in any way. If any of these
situations occur while the battery is in use or being charged, remove it from
the device or charger immediately and discontinue use. 11 DO NOT pierce the
battery casing with a nail or any other sharp object. Break it open with a
hammer, or step on it! Dispose or recycle this battery as it may cause
personal injury or damage to your drone. 12 Always charge the batteries on a
fireproof surface and away from combustible materials. DO NOT charge on
surfaces that can catch fire, including wood, cloth, carpet. 13 DO NOT immerse
the battery in water or get it wet. 14 DO NOT solder battery terminal in any
way. 15 Keep batteries out of reach of children or pets. 16 DO NOT short-
circuit the battery by connecting wires or other metal objects to the
positive(+) and negative(-) terminals.
Li-Po Battery Disposal & Recycling
Waste Lithium-polymer batteries must not be placed with household trash. To
dispose of waste batteries, please contact the local environmental or waste
agencies, the supplier of your model, or your nearest Li-Po battery recycling
center.
-04-
MAINTENANCE
æ Clean the drone after each use with a clean, soft cloth. ç Avoid prolonged
exposure to direct sunlight and avoid buildup of heat on the drone or
batteries. è This device is not waterproof and must not be submerged or
subjected to water under any circumstance. Failure to keep the device
completely dry may likely damage the unit permanently. Be aware that although
it might be dry where you are, droplets of rain or mist from a river or
waterfall could damage your drone where it is flying. é Frequently check the
charging plug and other accessories for signs of damage. If any part of the
device or cables are damaged, avoid using or charging until the damaged parts
are replaced.
-05-
PACKAGE CONTENTS
Drone
Transmitter
Drone Battery
Propeller
USB Charging Cable
Instructions For Use Gebrauchsanweisung
V 2.0
HT50 holyton@foxmail.com (USA) holyton_eu@foxmail.com (EU)
holyton_ca@foxmail.com (CA)
Instructions For Use
Screwdriver
-06-
DRONE DETAILS
Propeller A
Propeller B
Propeller B
HD Camera
Propeller A
Drone Battery
Indicator Lights -07-
TRANSMITTER DETAILS
Phone Holder
Take Photo Record Video
Left Joystick
Power Switch Unlock/Takeoff /Landing
Headless Mode (Short Press)/
Calibrating the Compass
(Long Press)
Lens Up Lens Down Right Joystick/ Speed Switch Folded Handle Charging Port
Return to Home
Antenna
-08-
JOYSTICK MODE
MODE 2 (Left hand throttle MODE 2 will be the default setting.)
Left Joystick
Up
Ascend
Right Joystick
Up
Forward
———————————————————–
Down
Descend
Down
Backward
Left
Right
Rotate
Left
Left
Right
Rotate
Fly to
Right
Left
Fly to Right
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
MODE 1 To enter MODE 1, turn on the transmitter while holding the “Record
Video” button. (Please do not release the “Record Video” button until the
transmitter is powered on.)
Left Joystick
Up
Forward
Right Joystick
Up
Ascend
———————————————————–
Down
Backward
Down
Descend
Left
Right Rotate Left
Rotate Right
Left
Right Fly to Left
Fly to Right
-09-
PREPARATION BEFORE FLIGHT CHARGING
USB Adapter (5V/2A)
(Not included)
Charging time: about 220 minutes.
Charging time: about 60 minutes.
(Charging) (Fully Charged)
(Charging) (Fully Charged)
Connect the USB charging cable to a USB Adapter(5V/2A), and then connect with the charging port of the drone or transmitter.
– Before charging, please read the instructions in the “Use of Battery” section of the “Safety Guidelines” carefully! – Please use the original charging cable to charge the battery. – DO NOT charge the drone battery immediately after a flight as the temperature of the battery may be too high. Please wait until it cools down to room temperature before charging again.
-10-
PREPARATION BEFORE FLIGHT DOWNLOAD APP
iOS
Android APP on Google play
Scan the corresponding QR code and download the HT Drone app for free. Required Operating Systems: iOS 11.0 or later/Android 5.0 or later
GIMBAL COVER
æ Push the gimbal cover according to the arrow’s direction as shown
above.(Pic.A) ç Pull the gimbal cover up then gently take it off. (Pic.B)
cPlease remove the gimbal cover gently before powering on the drone. cPlease
put the gimbal cover back on when the drone is not in use.
-11-
PREPARATION BEFORE FLIGHT DRONE BATTERY
Push the battery correctly into the drone battery compartment. Make sure that
you hear a click sound, which indicates that the battery is firmly installed.
Attention: The battery should be installed firmly. Otherwise, the flight
safety of your drone may be affected. The drone may crash due to a power-cut
during the flight.
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
æ ç
Removal: Press the lock button on the battery and pull it back to remove the
battery from the fuselage.
-12-
PREPARATION BEFORE FLIGHT ARMS
All arms of the drone are folded before the drone is packaged at the factory.
First, unfold the front arms, then unfold the rear arms.
TF CARD
To store your photos and videos, insert the TF card (not included) into the
slot as shown above before turning on the drone. The drone supports TF card up
to 256GB.
-13-
PREPARATION BEFORE FLIGHT
PROPELLERS
A
HEAD B
B
A
æAn “A” or “B” is printed on the propeller. çLock the propellers to the
corresponding the arms of drone (the arms are also marked) with screws.
èRotate each screws clockwise.
– The propeller is installed before the drone is packaged at the factory. –
The drone will not fly unless the correct propeller is installed on the
correct motor shaft.
FOLDABLE HANDLE/PHONE HOLDER
2
1 1
æExpand the foldable handle on the transmitter separately. çExpand the phone
holder and place your mobile phone in it. Adjust the clamp to secure your
mobile phone.
-14-
PREPARATION BEFORE FLIGHT ANTENNA
Before flying, please adjust the antenna on the back of the transmitter so it
is facing outward.
The signal between the drone and the transmitter is most reliable when the
transmitter is positioned toward the drone, as depicted above on the left. If
the transmission signal is weak during flight, adjust the orientation of the
transmitter to ensure that the drone is within optimal transmission range.
-15-
FLIGHT
All of the operations shown in this manual are demonstrated using MODE 2. ·
Pre-Flight Checklist 1. Make sure the transmitter, the mobile phone and the
drone battery are fully charged. 2. Make sure the drone battery and the
propellers are installed securely. 3. Make sure the drone arms are fully
expanded. 4. Make sure that there is nothing obstructing the motors. 5. Make
sure you use Holyton accessories.
PAIRING
HEAD
æPress once, then again and hold the Power Button for 3 seconds to turn on the
drone, and place it on a level surface with its head forward. The indicator
lights on the drone will blink. ç Press the power switch ( ) on the
transmitter to turn it on and it will sends out a beep, then the indicator
light on the transmitter will blink. èOnce the transmitter sends out a long
beep and the indicator lights on the drone and the transmitter will turn solid
if the drone is paired successfully.
-16-
FLIGHT
CONNECT TO WI-FI
HOLYTON — **
Connect your phone to the Wi-Fi network created by the drone. You can check
the drone’s status on the HT Drone app. æ Make sure to turn off Bluetooth,
Mobile Data, and VPN. Enter your phone’s Wi-Fi settings and click Wi-Fi to
search for the Wi-Fi of the drone. (Make sure the pairing has finished before
going to the Wi-Fi settings on your phone) ç Select the Wi-Fi network:
HOLYTON–**. è Wait for a couple of seconds for your phone to connect to
the drone’s Wi-Fi. é Enter the HT Drone app. > The connection between your
phone and the drone is established automatically.
Because the Wi-Fi network created by the drone cannot access the Internet,
your phone may inform you in various ways, like saying the connection isn’t
secure, or there is no internet connection, etc. Please ignore these messages.
Or, in the case of getting Pop-ups, choose the option that allows you to stay
with the current Wi-Fi.
-17-
FLIGHT CALIBRATING THE COMPASS
æ Long press the ( ) button, the transmitter will beep once, which indicates
that the drone entered the compass calibration.
ç Hold the drone horizontally and rotate it until the transmitter beeps once.
è Hold the drone vertically and rotate it until the transmitter beeps twice,
which indicates that the Compass Calibration is completed.
-18-
FLIGHT
GPS SEARCHING
HEAD
Place the drone on a flat and dry surface where is unobstructed and lit area.
When the drone indicator lights turn solid green, the transmitter will send
out a long beep, it means that the search for GPS signal is completed. This
process may take about one minute.
· The default mode is the GPS Mode. It is highly recommended to operate
outdoor flights in GPS mode for maximum safety. · If the GPS signal is weak or
flying indoors, please long press the Return to Home ( ) button to exit the
GPS mode. At this time, the drone is in Optical Flow Mode, and the maximum
flying altitude does not exceed 20ft. · In the optical flow mode, if the GPS
signal is available (7 or more satellites reception), the pilot can land the
drone and then take it off. At this time, the drone will automatically change
to GPS mode to get a higher height.
-19-
FLIGHT CALIBRATE THE GYRO
Simultaneously push the left joystick and the right joystick to the bottom
left corner to calibrate the gyro. The indicator lights on the drone will
blink, then turn solid, which indicates that the calibration is completed.
To ensure a stable flight, we suggest that the pilot calibrates the gyro every
time after pairing the drone and after a crash.
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
TAKEOFF/LANDING
æ Unlock: Short press the ( ) button to unlock the motors. ç Takeoff: Short
press the same button again, the drone will automatically take off and hover
at 5 ft. At this time, you can control this drone by using the joysticks. è
Landing: When the drone is flying, short press the ( ) button, and the drone
will automatically land on the ground.
-20-
FUNCTION DETAILS
EMERGENCY STOP
The Emergency Stop function should only be used in case of emergency during
the flight to avoid any damage or injury.
Long Press
Long Press
Press and hold the ( ) button and the ( ) button simultaneously for 2 seconds, the transmitter will beep continuously, and The drone will descend quickly to the ground.
SPEED SWITCH
This drone comes with 2 speed modes (Low/High). Press down on the right
joystick to switch between low and high speed. The transmitter beeps once to
indicate Low Speed, beeps twice to indicate High Speed. (The Low speed is the
default speed mode.)
-21-
FUNCTION DETAILS TAKE PHOTO/RECORD VIDEO
Take Photo: Short press the ( ) on the transmitter to take photos. The
transmitter will beep once, which indicates that the camera has successfully
taken one photo.
Record Video: Short press the ( ) on the transmitter. The transmitter will
beep twice, which indicates that the recording has started. Press again to
exit the recording. (You will hear two beeps from the transmitter.)
CAMERA ANGLE ADJUSTMENT
100° As shown in the figure above, you can adjust the camera to tilt up or
down through the two buttons ” ” and ” “. (The camera has an 100° tilt range.)
-22-
FUNCTION DETAILS
HEADLESS MODE
The Headless Mode is a great training tool for beginner pilots. It is also
useful when the drone is too far from the pilot (which makes it difficult to
tell its orientation). It keeps the drone traveling forward, backward, left,
or right when you move the right joystick in those directions, regardless of
which way the front of the drone is pointed.
The pilot should stay facing the same direction that the drone’s head points to when it takes off.
Entering: Short press the (
) button on the transmitter, and the
transmitter will send out beeps continuously, which indicates the drone is in
Headless Mode.
Exiting: Short press the button again, and you will hear a beep which
indicates the drone exits the Headless Mode.
-23-
FUNCTION DETAILS
- Why is the orientation of the drone important? In normal flying mode, the control of the drone movement can sometimes be counter-intuitive for beginners. For instance, when the drone is in the air with its head pointing to your right, if you push the right joystick forward, the drone will fly to your right, instead of flying forward. With the headless mode, the drone has a fixed “head.” In Headless Mode, the drone always remembers the side its head points to during takeoff as the front side. This means that if the drone takes off with its head pointing forward, it doesn’t matter how the drone is oriented in the air, when you push the right joystick forward, the drone will fly forward. Or, when its head is pointing to you, if you push the right joystick to the left, the drone will fly to your left.
RETURN TO HOME(RTH)
· The Return to Home function brings the drone back to the recorded Home Point. · The Home Point is the location at which the last recorded takeoff point (7 or more satellites reception) of the drone. The current position of the drone will be recorded as the Home Point .
-24-
FUNCTION DETAILS
Smart RTH
If the GPS signal is available (7 or more satellites reception) and the Home
point is recorded previously. Press the ( ) button on the transmitter, then
the drone will fly back to the Home Point automatically. Exit the RTH mode by
pressing the ( ) button again.
Failsafe RTH
If the GPS signal is available (7 or more satellites reception) and the Home
Point is recorded previously. Failsafe RTH will be triggered when the
transmitter signal is lost for more than 10 seconds. The drone will fly back
to the Home Point automatically. If the transmitter’s signal is recovered and
you want to exit the Failsafe RTH, you can press the ( ) button again.
The default RTH altitude for the above two Return Home modes is 66ft. There
are 2 possible scenarios:
a. When the drone’s current altitude is higher than or equal to 66ft, the
drone will maintain its current altitude, fly back above the Home Point, then
descend to the ground.
b. When the drone’s current altitude is lower than 66ft, the drone will first
ascend to 66ft altitude, fly back above the Home Point, then descend to the
ground.
-25-
FUNCTION DETAILS
The First Stage of Low Voltage RTH
The First Stage of Low Voltage RTH is automatically triggered when the Drone
Battery Level icon will blink yellow on the APP, and the transmitter will beep
continuously. The drone will fly back to the Home Point automatically. At this
time, the pilot can take off the drone again and operate it within a safe
range (Flight Altitude 66ft, Flight Distance 66ft).
The Second Stage of Low Voltage RTH
When the Drone Battery Level icon will blink red on the APP, and the
transmitter will beep continuously and rapidly, the drone will descend
directly to the ground.
· During the RTH procedure, the drone can NOT avoid obstacles. · When there is
a pre-recorded Home Point, but the drone cannot receive any GPS signal, the
RTH procedure cannot be completed. The drone will just maintain its current
altitude and position.
· Flight Distance: The horizontal distance between the Home Point and the
drone. · Flight Altitude: The vertical distance between the Home Point and the
drone.
-26-
STABILIZATION FUNCTION AlTITUDE-HOLD FUNCTION
The drone is designed with an altitude-hold function to maintain its altitude
after releasing the left joystick. (The left joystick will automatically
spring back to the middle)
OPTICAL FLOW POSITIONING
Vision Positioning Lens
The Optical Flow Positioning System consists of a camera module, which
acquires the position information of the drone through visual images to ensure
precise positioning of the drone.
-27-
STABILIZATION FUNCTION
The Optical Flow Positioning System is typically used in an indoor environment
when the GPS signal is weak or unavailable. It works best when the drone
altitude is less than 10 ft.
cThe precision of the Optical Flow Positioning System is easily affected by
the light intensity and features of the surface textures. Once the image
sensor is not available, your drone will switch to the altitude-hold function
automatically. Please be cautious to operate the drone in the following
situation: 1. Fly fast at an altitude below 2 ft. 2. Fly over monochrome
surfaces (e.g, pure black, pure red and pure green). 3. Fly over highly light
reflective surfaces. 4. Fly over water or transparent surfaces. 5. Fly over
moving surfaces or objects. 6. Fly in an area where the lighting changes
dramatically and frequently. 7. Fly over extremely dark (<10 lux) or bright (>
10,000 lux) surfaces. 8. Fly over surfaces without clear patterns or textures.
9. Fly over surfaces with highly repeating textures (small grid brick in the
same color). cFlying speed should be controlled not to be too fast. When the
drone is 3 ft from the ground, the flying speed should not be over 16 ft/s.
When the drone is 7 ft from the ground, the flying speed should not be over 33
ft/s.
-28-
STABILIZATION FUNCTION
cKeep sensors clean at all times. cThe Optical Flow Positioning is only
effective when the drone is within the altitude range of 10 ft. cMake sure
that the light is bright enough and the surface is with clear textures so that
the Optical Flow Positioning can acquire the movement information through
recognizing the ground textures. cThe Optical Flow Positioning may not
function properly when the drone is flying over water, low light ground and
surfaces without clear patterns or textures.
-29-
APP OPERATION INSTRUCTION OPERATION INTERFACE
Homepage: Tap this icon to return to the main menu. GPS Signal: Displays the
current GPS signal strength. Wi-Fi Signal Strength: Displays the current
signal strength between the drone and the mobile phone. Transmitter Battery
Level: Real-time display of the current battery level of the transmitter.
Drone Battery Level: Real-time display of the current battery level of the
drone. Flight Setting: Tap to enter the setting interface. Alter settings for
flight height/distance, etc.
-30-
APP OPERATION INSTRUCTION
VR: Tap to split the screen. Then place the mobile phone into a VR headset
(not included) to watch the live feed in 3D. TapFly: Set any points on the map
to draw the flight path, and then the drone will fly along this route. (It is
recommended to enlarge the map) Follow Me Mode: The drone stays at a distance
from the operator and following the GPS position of the phone.
Helix: The drone flies upwards and circles. Hand Gesture: Perform the gesture
within 6.6ft of the drone while facing toward the camera and it will begin
taking a selfie.
Rocket: The drone will rise vertically for a certain height.
Circle: The drone will circle clockwise or counterclockwise.
Dronie: The drone flies backward and upward, with the camera locked on your
subject.
Return to Home: Tap to bring the drone back to the Home Point.
Unlocking: Tap to to unlock the drone, the motor starts to rotate.
Photo/Video: Tap to switch between photo taking and video recording.
Shutter/Record Button: Tap to take a photo or to start or stop recording a
video.
Album: Tap to view photos and videos taken by the drone’s camera.
Map: Tap to switch between Camera View and Map View.
H: 0.0m Flight Parameters: Displays the flight height between the drone and
D: 0.0m HS: 0.0m/s
the
takeoff
point,
the
flight
distance
from
the
takeoff
point,
drone
VS: 0.0m/s horizontal speed, and drone vertical speed.
-31-
APP OPERATION INSTRUCTION
BEGINNER MODE
The default GPS mode is the beginner mode. When in this mode: 1. Flight
Distance is limited between 0~98 ft. 2. Flight Altitude is limited between
0~98 ft. If you want to enter the anvanced mode, you need to exit the beginner
mode by turning off the beginner mode as show below. At this time, you can
acquire farther flight distance.
Flight Settings On APP
Parameter
Track
Beginner
Turn on for novice mode by default and turn off for custom mode
Total Flight
distance
Default 30m, (20-500m)
30
Flight altitude Default 30m, (10-120m)
30
Unit
Inch (MPH)
Voice prompt
Metric (m/s) Metric (km/h)
-32-
SPECIFICATIONS
DRONE Model: HT50 Weight: 245g/8.6oz Max Flight Time: 25 minutes (per battery)
Operating Temperature Range: 14° to 104°F Size: 290 × 260 × 55 mm (Unfolded)
145 × 85 × 55 mm (Folded)
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
DRONE BATTERY Capacity: 2100 mAh Voltage: 7.7 V Battery Type: Lithium-ion
Polymer Battery Energy: 16.17 Wh Charging Temperature Range: 41° to 104°F
Charging Time: about 220 minutes
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
TRANSMITTER Operating Frequency: 2452-2474 MHz Max Flight Distance: 1640 ft
(outdoor and unobstructed) Battery Type: 3.7V 380mAh Lithium-ion Polymer
Battery Operating Temperature Range: 14° to 104°F Charging Time: 60 minutes
Usage Time: about 10 hours
-33-
SPECIFICATIONS
CAMERA Operating Frequency: 5500-5700MHz Photo Resolution: 4096×3072P (stored
in TF card) 4096×3072P (stored on mobile phone) Video Resolution:
2688×1512P@25fps (stored in TF card) 1920×1080P@25fps (stored on mobile phone)
Lens: FOV 120° Max Transmission Distance: 1640 ft (outdoor and unobstructed)
Photo Formats: JPEG Video Formats: AVI/MP4 Supported TF Cards: Supports a TF
Card (Class10 above) with capacity of up to 256 GB (Not included) File
Systems: FAT32
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
USB CHARGING CABLE Input: 5V/2A Rated Power: 10W
-34-
CONTACT US
Please do not hesitate to contact us if you need further support.
holyton@foxmail.com (USA) holyton_ca@foxmail.com (CA) holyton_eu@foxmail.com
(EU) 4:00 PM ~ 7:00 AM (PST)
For online support, please scan this code with Live Chat
-35-
GENERAL INFORMATION
FCC Notice: This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference. (2) This device must accept any interference received, including
interference that may cause undesired operation.
Supplier’s Declaration of Comformity Product Name: Quadcopter Model NO: HT50
Responsible Party: JL TRADING CO LTD Responsible Party Address: 5940 S RAINBOW
BLVD STE 400-79525 LAS VEGAS, NV 89118 US Phone Number:
626-766-6284
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
set to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy, if not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can not be determined by turning the
equipment off and on, the user is encouraged to try one or more of the
following measures: —Reorient or relocate the receiving antenna. —Separation
more distance between the equipment and receiver. —Connect the equipment to an
outlet on a circuit different from the receiver. —Consult the dealer or an
experienced radio/TV technician for help.
-36-
GENERAL INFORMATION
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
RF Exposure The equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This device should be installed and
operated with minimum distance 20cm between the radiator & your body. This
part belongs to the drone.
RF warning for Portable device: The device has been evaluated to meet general
RF exposure requirement. The device can be used in portable exposure condition
without restriction. This part belongs to the transmitter.
IC Notice: This device is restricted to indoor use when operating in the 5150
to 5250 MHz frequency range. This device complies with Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device.
CAN ICES-003 (B) Avis d’Industrie Canada Le présent appareil est conforme aux
CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne
doit pas produire de brouillage, et
-37-
GENERAL INFORMATION
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
CAN NMB-003 (B) RF Exposure Radiation Exposure Statement: The device is
compliance with RF exposure guidelines, users can obtain Canadian information
on RF exposure and compliance. The minimum distance from body to use the
device is 20cm.
Le présent appareil est conforme Après examen de ce matériel aux conformité ou
aux limites d’intensité de champ RF, les utilisateurs peuvent sur l’exposition
aux radiofréquences et compliance d’acquérir les informations correspondantes.
La distance minimale du corps à utiliser le dispositif est de 20cm.
HOW TO RECYCLE THIS PRODUCT This symbol on the product or its documentation
indicates that it must not be disposed of with household waste. Uncontrolled
waste disposal may harm the environment or human health. Please separate your
device from other types of waste to recycle it responsibly. This will help to
foster the sustainable re-use of material resources. We invite you to contact
your retailer or inquire at your local town hallto find out where and how the
drone can be recycled.
-38-
GENERAL INFORMATION
BATTERY WARNING: 1. Failure to follow all the instructions may result in
serious injury, irreparable damage to the battery and may cause a fire, smoke
or explosion. 2. Always check the battery’s condition before charging or using
it. 3. Replace the battery if it has been dropped, or in case of odor,
overheating, discoloration, deformation or leakage. 4. Never use anything
other than the approval LiPo charger the battery. Always use a balancing
charger for LiPo cells or a LiPo cell balancer. It is recommended that you do
not to use any other charger than the one provided with the product. 5. The
battery temperature must never exceed 60°C (140°F) otherwise the battery could
be damaged or ignite. 6. Never charge battery on a flammable surface, near
flammable products or inside a vehicle (preferably place the battery in a non-
flammable and nonconductive container). 7. Never leave the battery unattended
during the charging process. Never disassemble or modify the housing’s wiring,
or puncture the cells. Always ensure that the charger output voltage
corresponds to the voltage of the battery. Do not short circuit the batteries.
8. Never expose the LiPo battery to moisture or direct sunlight, or store it
in a place where temperatures could exceed 60°C(car in the sun, for example).
9. Always keep it out of reach of children. 10. Improper battery use may
result in a fire, explosion or other hazard.
-39-
GENERAL INFORMATION
11. Non-rechargeable batteries are not to be recharged. Rechargeable
batteries are only to be charged under adult supervision. 12. Different types
of batteries or new and used batteries are not to be mixed. 13. Batteries are
to be inserted with the correct polarity. 14. The supply terminals are not to
be short-circuited. Regular examination of transformer or battery charger for
any damage to their cord, plug, enclosure and other parts and they must not be
used until the damage has been repaired. 15.The packaging has to be kept since
it contains important information. 16.This toy should only be connected to the
equipment with symbol Class II.
EU RF Power (EIRP): 16 dBm (2452~2474MHz)
Caution 1. The max operating of the EUT is 45°C. and shouldn’t be lower than
-10°C. 2. The device complies with RF specifications when the device used at
0mm from your body. 3. Declaration of Conformity.
We, Xiamen Huoshiquan Import & Export CO., LTD hereby, declare that the
essential requirements compliance with the Directive 2014/53/EU, the RoHS
Directive 2011/65/EU and Safety Directive 2009/48/EC have been fully fulfilled
on our product with indication below: Product Name: REMOTE CONTROL MODEL/RADIO
CONTROLLED Model/Mark: HT50/HOLYTON
-40-
GENERAL INFORMATION
The Statement of compliance is available at the following address:
http://www.holystone.com/Download/CE/HT50_EU_DOC.pdf This product can be used
across EU member states. MANUFACTURER INFORMATION Manufactured by Xiamen
Huoshiquan Import & Export CO.,LTD Address: Unit 1, Room 501, Hongxiang
Building, No.258 Hubin Nan Road, Siming District, Xiamen, China
+1(855)888-6699
MADE IN CHINA(CN) -41-
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>