Hisense Cube C1 4K TriChroma Laser Smart Mini Projector User Guide

Hisense Cube C1 4K TriChroma Laser Smart Mini Projector User Guide

Important Safety Information

SAFETY WARNINGS

Do not look directly at the lens when this device is on!

• This product comes with a laser module. Do not tear or modify this device in any manner; otherwise, it may result in personal injury.
  RG1
  IEC 62471-5: 2015
  CLASS 1 LASER PRODUCT IEC 60825-1:2014
  As with any bright light source, DO NOT STARE INTO THE BEAM
  X = 458-472nm/519-531nm/635-651nm
  Wavelength 458-472nm/519-531nm/635-651nm
  Caution-use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
  The Device Complies with 21 CFR 1040.10 and 1040.11 except for confromance as a Risk Group[0,1 or 2-Select appropriate RGJLIP as defined in IEC 62471-5: Ed.1.0. For more information see Laser Notice No.57, dated May 8, 2019.

• If this device requires a repair, please wear laser eye protection with an optical density OD that is 4 or higher and has a wave length of 458-651 nm.

• Do not place any water-containing vessel on this device, such as cosmetics or liquid medicine.

• If any object or water enters this device, please unplug this device and contact the service staff of Hisense.

• Do not place any exposed fire source (e.g. burning candle) on this device.
  Keep away from high temperature and heat.

• Do not expose the battery to direct sunlight or candle light.

• Keep air vents on both sides clear from any objects to prevent the device from overheating inside.

• To avoid a short circuit, product damage or electric shock, do not use any sharp object or metal to touch the ports or other openings on the device.

• If this device has been in a warm environment, allow any built-up condensation to evaporate first BEFORE you switch the device on.

• Do not allow a child to stand on or climb up this device.

• Do NOT place any object above or in front of the lens because the laser light could cause the object to become flammable.

• Clean the lens periodically with a clean cloth and make sure the device is turned off before you start.

Low Blue light Content

• The long-term exposure to blue light may damage your eyes, in particular the retina, causing visual fatigue or eye strain. Children are particularly vulnerable to excessive blue light and the damage to them is irreversible. The product can decrease blue light ratio to reduce blue light hazard.

Health recommendations

• Avoid long time continuous use product, ensure adequate break time.
• Looking at distant objects or exercises for the eye after use product.

Packaged Contents

• Smart Mini Projector
• 1 Remote Control
• 2 AAA Batteries
• 1 Power Cord
• 1 Power Adapter
• Quick Setup Guide
• Important Safety Information & Warranty Card
• 1 HDMI Extension Adapter

NOTE:

• The accessories may be different from the list above due to different models, countries/regions. Please refer to the actual accessory bag.
• Screen is not included.

Smart Mini Projector Diagram

Detection range:

1. CMOS image sensor module: DFOV:78°, HFOV:70°, VFOV:43°
2. Time-of-Flight Sensor: 400mm-2000mm, FOV:27°

NOTE:

• The rated detection range of sensors may vary with different testing environments and conditions under different test product.
• Risks are inevitable in the usage of the projector even with eye protection function on. Children must be accompanied by adults when using it.
• Product image is only for reference, actual product may vary in appearance.

Use Your Remote

1. Power on/Standby
2. Press to enable automatic focus
3. D-pad (up/down/left/right navigation buttons)
4. Return to the previous place in the menu or app
5. Volume (up/down)
6. Media content control function buttons
7. Quick access to picture mode
8. Change input source
9. Activate the microphone
10. Input numbers and special function buttons
11. Confirmation button
12. Press to enter Menu
13. Press and hold to pair the bluetooth remote
14. Display the Home screen
15. Adjust brightness
16. Press to Mute or restore sound
17. Quick access to sound mode
18. Quick access buttons to apps

NOTE:

• The included remote will vary depending on models, countries/regions. Check information according to the actual remote in the accessory bag.
• Insert two AAA size batteries. Make sure to match the (+) and (-) ends of the batteries with the (+) and (-) ends indicated in the battery compartment.
• The remote control can work at a distance of up to 8 metres in front of the device.

Basic Operation

Turning the device on or off

1. Plug the power cord into a wall outlet.
2. Press the button on the remote to turn on the device. When you turn it on for the first time, follow the instructions displayed on the screen and configure the device’s basic settings

NOTE:

• When the device is started up, you can press the button on the remote to turn it into standby mode; When the device is in stanby mode, you can press the button on the remote to turn on the device.

• Plug the power cord off a wall outlet when you do not use the device for a long time.

• Please waite at least 10 seconds to turn on the device again when it is shut down
  WARNING: Insufficient ventilation space will cause this device to overheat or become damaged.

• Do not block the air vents or place any object on this device.

• Do not place this device in any narrow, enclosed or poorly ventilated space.
  

• At a minimum, leave the amount of space shown in the diagram below for this device to have proper ventilation

Automatic Focus

When the automatic focus function is enabled, the device can automatically adjust the focus to make your projector picture clear.

• Enable automatic focus function by pressing the button on the remote.
• You can enable manual focus function by pressing and holding the the button, and manually adjust the focus by pressing the D-pad on the remote.

Automatic Correction

Press Home button on your remote, and select Settings > Projector > Auto Correction.
The device can perform automatic keystone correction on the projected screen and automatically changes the screen shape into a rectangle.

More Settings

Press Home button on your remote, select Settings to enter the Settings Menu to set up your device.

NOTE:

• For detailed instructions, please refer to the E-Manual.
• Parts of the software function changes with the system upgrade.

Image Size and Projection Distance

Projection Distance| 150″| 120”| 100″| 90″| 80″| 70″|  65″
---|---|---|---|---|---|---|---
mm| 3985| 3188| 2657| 2391| 2125| 1860| 1727
inchi| 157| 126| 105| 94| 84| 73| 68

Text-to-Speech (TTS)

Text-to-Speech (TTS) can help you to navigate the menus on the screen.
Text-to-Speech can convert written text into voice text to help visually impaired people listen to the information they are unable to read.

1. Press the Home button on your remote.
2. Next, select Settings to enter the Settings Menu.
3. Select Accessibility > Voice Guide.

When Voice Guide is turned on, then the contents of each menu displayed can be broadcasted out.
https://www.hisense-usa.com/hisense-laser-cinema-c1-text-to-speech

Maintenance

• Do not touch this device when it is running or just turned off because it may be hot.
• Do not wipe this device with oil because it may deteriorate the exterior or damage the paint.
• Contact with rubber or ethylene products for a long time may cause stains on this device.
• If the outside of the device is dirty, turn off the device and wipe with a damped soft cloth.
• Do not touch the lens with your hands.
• Do not touch or wipe the lens with ordinary cleaning cloth. Use a dust blower to remove the dust on the lens. Grease, dirt and fingerprints should be cleaned carefully by the professional by using optical cleaning cloth, lens wiping paper or professional cleaning solutions to avoid destroying the optical filming and affecting the image quality.
• To turn off this device, press the Power button on the remote control. Do not cut off the power directly when the device is working.

Product Specifications

– 75% RHAtmospheric pressure: 86 kPa – 106 kPa
Storage Temperature| 5°F to 113°F (-15°C to 45°C)
Storage Humidity| 10% to 70%, non-condensing

Disclaimer:
All products, product specifications, and data are subject to change without notice to improve reliability, function, design or otherwise

Certification and Compliance

FCC Notice

This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications

However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or Smart Mini Projector reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Increase the separation between the device and receiver
• Connect the device into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/Smart Mini Projector technician for help

The Wi-Fi Module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR SMART MINI PROJECTOR INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT

Declaration of Conformity

Trade Name: Hisense
Model: C1
Responsible Party: Hisense USA Corporation
Address: 106 Satellite BLVD Suite I. Suwanee, GA 30024
Telephone Number: 1-888-935-8880

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful. interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Dolby, Dolby Vision, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby Laboratories. Confidential unpublished works. Copyright © 2012-2022 Dolby Laboratories. All rights reserved.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

©2023. All rights reserved. Hisense and the Hisense logo are registered trademarks of Hisense. Other brand and product names are registered trademarks of their respective owners.

Register Your Device!

Because we value your business, we want to keep you in the know of all things Hisense’. Using your mobile phone, scan the Registration page QR code to register your Device. Depending on the make and model of your phone, you may need to download a QR code scanning app

US

http://www.hisense-usa.com/support/register

Мекко

https://hisense.com.mx/support/register

Canada

http://www.hisense-canada.com/support/productReg.asp

Disclaimer
Subscriptions or other payments may be required to access content through some appications. Some or all of the included or downloaded application services In this Hisense device may not function depending on the Internet connection, local limitations of Included applications or other reasons outside of Hisense’s control. HISENSE EXPRESSLY DISCLAIMS RESPONSIBILITY FOR ANY APPLICATION SERVICE FROM FUNCTIONING AT ANY TIME, FOR CONTENT IN ANY APPLICATION SERVICE, FOR DISRUPTIONS OF SERVICE, LOCAL OR REGIONAL LIMITATIONS, WARRANTIES OF TITLE, NO INFRINGEMENT, AND FOR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. By purchasing this device, you accept such Disclaimer without any claim on Hisense at any time

2023 Hisense Company Ltd. All Rights Reserved

All material in this Quick Setup Guide is the property of Hisense Company Ltd. and its subsidiaries, and is protected under US, CANADA, MEXICO and International copyright and/or other intellectual property laws. Reproduction or transmission of the materials, in whole or in part, in any manner, electronic, print, or otherwise, without the prior written consent of Hisense Company Ltd. is a violation of Hisense Company Ltd. rights under the aforementioned laws.

No part of this publication may be stored, reproduced, transmitted or distributed, in whole or in part, in any manner, electronic or otherwise, whether or not for a charge or other or no consideration, without the prior written permission of Hisense Company Ltd.

Requests for permission to store, reproduce, transmit or distribute materials may be made to one of the following addresses:

U.S.A.
Hisense USA Corporation 105 Satellite BLVD Suite I, Suwanee, GA 30024

MEXICO IMPORTER:
Hisense Mexico S. de R.L. de C.V. Blvd. Miguel de Cervantes Saavedra No 301 Torre Norte Piso 2, Col. Ampliación Granada Miguel Hidalgo, Ciudad de México, C.P. 11520
RFC: HME1105121Y3
TEL: (52) (55) 5531-3515

CANADA
Hisense Canada Co., Ltd 2283 Argentia Road, Unit 16 Mississauga, ON, Canada L5N 522

Hisense, and any and all other Hisense product names, logo’s, slogans or marks are registered trademarks of Hisense Company Ltd. and its subsidiaries. All other trademarks are the property of their respective holders.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>