BLACK DECKER BDECS200 13 AMP Circular Saw Instruction Manual

: June 14, 2024
: Black Decker

BLACK DECKER BDECS200 13 AMP Circular Saw

BLACK DECKER BDECS200 13 AMP Circular Saw

Thank you for choosing BLACK+DECKER

PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY REASON.
If you have a question or experience a problem with your BLACK+DECKER purchase, go tohttp://www.blackanddecker.com/instantanswers If you can’t find the answer or do not have access to the Internet, call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. – Fri. to speak with an agent.
Please have the catalog number available when you call.

SAVE THIS MANUAL FOR FUTURE REFERENCE. VEA EL ESPANOL EN LA CONTRAPORTADA.

To register your new product, visit www.BlackandDecker.com/NewOwner

DEFINITIONS: SAFETY ALERT SYMBOLS AND WORDS

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risks of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
NOTICE: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.

General Power Tool Safety Warnings

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/ or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dustrelated hazards.
POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
SERVICE
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Safety Instructions for All Saws

DANGER: Keep hands away from cutting area and the blade. Keep your second hand on auxiliary handle or motor housing. If both hands are holding the saw, they cannot be cut by the blade.
b) Do not reach underneath the workpiece. The guard cannot protect you from the blade below the workpiece.
c) Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece.
d) Never hold piece being cut in your hands or across your leg. Secure the workpiece to a stable platform. It is important to support the work properly to minimize body exposure, blade binding, or loss of control.
e) Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and could give the operator an electric shock.
f) When ripping always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance of blade binding.
g) Always use blades with correct size and shape (diamond versus round) of arbour holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control.
h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation.

Causes and Operator

Prevention of Kickback:

a) Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces. Position your body to either side of the blade, but not in line with the blade. Kickback could cause the saw to jump backwards, but kickback forces can be controlled by the operator, if proper precautions are taken.
b) When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or kickback may occur. Investigate and take corrective actions to eliminate the cause of blade binding.
c) When restarting a saw in the workpiece, center the saw blade in the kerf and check that saw teeth are not engaged into the material. If saw blade is binding, it may walk up or kickback from the workpiece as the saw is restarted.
d) Support large panels to minimize the risk of blade pinching and kickback.
Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.
e) Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback.
f) Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and kickback.
g) Use extra caution when sawing into existing walls or other blind areas.
The protruding blade may cut objects that can cause kickback.

Lower Guard Safety Instructions

a) Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut.
b) Check the operation of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.
c) Lower guard should be retracted manually only for special cuts such as “plunge cuts” and “compound cuts.” Raise lower guard by retracting handle and as soon as blade enters the material, the lower guard must be leased. For all other sawing, the lower guard should operate automatically.
d) Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.

Additional Safety Instructions

Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
Keep your body positioned to either side of the blade, but not in line with the saw blade. KICKBACK could cause the saw to jump backwards (see Causes and Operator Prevention of Kickback and KICKBACK).
Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.
Always make sure nothing interferes with the movement of the lower blade guard.
Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. Accessory ratings must always be above tool speed as shown on tool nameplate.
Always make sure the saw is clean before using.
Stop using this saw and have it properly serviced if any unusual noise or abnormal operation occurs.
Always be sure all components are mounted properly and securely before using tool.
Always handle the saw blade with care when mounting or removing it or when removing the diamond knockout.
Always wait until the motor has reached full speed before starting a cut.
Always keep handles dry, clean and free of oil and grease. Hold the tool firmly with both hands when in use.
Always be alert at all times, especially during repetitive, monotonous operations.
Always be sure of position of your hands relative to the blade.
Stay clear of end pieces that may fall after cutting off. They may be hot, sharp and/or heavy. Serious personal injury may result.
Replace or repair damaged cords. Make sure your extension cord is in good condition. Use only 3-wire extension cords that have 3-prong grounding-type plugs and 3-pole receptacles that accept the tool’s plug.
An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

WARNING: Blades coast after turn off. Serious personal injury may result.

WARNING: ALWAYS wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

WARNING: ALWAYS use proper eye protection. All users and bystanders must wear proper eye protection that conforms to ANSI Z87.1.

WARNING: ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty.

ALWAYS wear certified safety equipment:

ANSI Z87.1 eye protection (CAN/CSA Z94.3).
ANSI S12.6 (S3.19) hearing protection.
NIOSH/OSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known in the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

Lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-treated lumber (CCA). Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

WARNING: Cutting plastics, sap coated wood, and other materials may cause melted material to accumulate on the blade tips and the body of the saw blade, increasing the risk of blade overheating and binding while cutting.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. Always operate tool in well-ventilated area and provide for proper dust removal. Use dust collection system wherever possible.

SYMBOLS

The label on your tool may include the following symbols. The symbols and their definitions are as follows:

V……………..volts
mW………….milliwatts
nm …………..wavelength in nanometers
A……………..amperes
Hz……………hertz
W…………….watts
min ………….minutes
or AC …..alternating current
Symbol or DC…direct current
no ……………no load speed
……………Class I Construction (grounded)
…………….earthing terminal
…………..safety alert symbol
…………….Class II Construction (double insulated)
…/min or rpm…revolutions or reciprocation per minute
………..Read instruction manual before use
…………….Use proper respiratory protection
……………Use proper eye protection
…………….Use proper hearing protection

To Reduce the Risk of Kickback

Keep a firm grip on saw with both hands at all times.
Stay alert – exercise control.
Support long overhanging materials. As the material is cut and weakens, it will sag, causing a pinched blade.
Support large panels as shown (Figure A).

Material supported only at the ends (Figure B) will lead to blade pinching.
Avoid sawing overhead. Material can sag and will pinch blade.
Insure that the material to be cut is clamped (Figure C) and solidly supported and balanced on a strong, stable and level work surface. Support the work so that the wide portion of the saw shoe is on the portion of the material that doesn’t fall after the cut is made. Never hold cut off piece by hand (Figure D )
Keep blades sharp and clean.
Use fence or straight edge guide when ripping. Be careful as the cut off strip can sag or twist, closing the cut and pinching the blade, leading to KICKBACK.
Don’t force tool. Wood variables such as knots, hardness, toughness, wetness, pressure treated and freshly cut green lumber can heavily load the saw which can lead to stalling. Push the saw slower when this occurs.
Don’t remove saw from work during a cut while the blade is moving.
Allow saw to reach full speed before blade contacts material to be cut. Starting the saw with the blade against the work or pushed forward into cut can lead to stalling or sudden backward movement of saw.
Never attempt to lift saw when making a bevel cut. This leads to blade binding and stalling.
Always secure work to prevent workpiece movement during cut.
Do not try to force saw back on line if your cut begins to go offline. This can cause KICKBACK. Stop saw and allow blade to coast down to a stop. Withdraw from cut and start a new cut on the line.
Set depth adjustment of saw such that one tooth of the blade projects below the workpiece as shown in (figure F).
Do not back up a rotating blade in the cut. Twisting the saw can cause the back edge of the blade to dig into the material, climb out of the work and run back toward the operator.
Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.

Safety Instructions – Lasers (BDECS300 ONLY)

DANGER: Laser radiation, avoid direct eye exposure, serious eye injury can result.

Do not use optical tools such as a telescope or transit to view the laser beam.
Position the laser so unintentional eye contact will be avoided.
Do not operate the laser around children or allow children to operate the laser.
Do not disassemble. Modifying the product in any way can increase the risk of laser radiation.

WARNING: Use of controls or adjustments or performance of procedures other than those specified in this manual may result in hazardous laser radiation exposure.

Do not operate in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
Storeidleproduct Out Of Reach Of children and other untrained persons. Lasers / power tools are dangerous in the hands of untrained users.
Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one laser / power tool, may create a risk of injury when used on another laser / power tool.
Repairs and servicing MUST be performed by a qualified repair facility. Repairs performed by unqualified personnel could result in serious injury.
Do not remove or deface warning labels. Removing labels increases the risk of exposure to radiation.
For indoor use only.
This product is intended for use in a temperature range of 41°F(5°C) – 104°F(40°C).

CAUTION: Use of controls or adjustments or performance of procedures other than those specified in this manual may result in hazardous laser radiation exposure.
The following laser warnings are located on your saw.

AVOID EXPOSURE. LASER RADIATION IS EMITTED FROM THIS APERTURE.

LASER RADIATION. DO NO T STARE INTO BEAM. CLASS 2 LASER PRODUCT. MAXIMUM OUTPUT < 1 mW, Wavelength: 650nm. IEC 60825-1:2007

|

COMPLIES WITH 21 CFR 1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED JUNE 24, 2007.

---|---

MOTOR
Be sure your power supply agrees with nameplate marking. 120 Volts AC means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that your tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in over-heating.
All BLACK+DECKER tools are factory tested; if this tool does not operate, check the power supply. This tool is AC only.

INTENDED USE

This circular saw is designed for wood cutting applications. Do not use water feed attachments with this saw. Do not use abrasive wheels or blades. Do not use under wet conditions or in presence of flammable liquids or gases. Do not cut metal, plastic materials, concrete, masonry, or fiber cement materials with this saw.

SAVE THESE INSTRUCTIONS

Functional Description

On/off switch
Main handle
Secondary handle
Shoe
Saw blade
Saw blade lower guard
Lower guard retracting lever
Laser (BDECS300 ONLY)
Bevel adjustment knob
Outer blade clamp washer
Blade retaining bolt
Depth adjustment lever
Depth scale
Bevel angle scale
Saw blade hex wrench
Spindle lock button

Assembly/Adjustment Set-Up

WARNING: Always unplug saw from power supply before any of the following operations.

ADJUSTING THE DEPTH OF CUT

The depth of cut should be set according to the thickness of the workpiece.

Loosen the depth adjustment lever (12) to unlock the saw shoe (4).
Move the saw shoe into the desired position ( Figure E ). The corresponding depth of cut can be read from the depth scale (13).
Tighten the lever to lock the saw shoe in place.
Set depth adjustment of saw such that one tooth of the blade projects below the workpiece as shown in Figure F.

ADJUSTING THE BEVEL ANGLE

This tool can be set to bevel angles between 0° and 45°.

Loosen the locking knob (9) to unlock the saw shoe.
Move the saw shoe (4) into the desired position ( Figure G ). The corresponding bevel angle can be read from the scale (14).
Tighten the locking knob to lock the saw shoe in place.

INSTALLING THE BLADE

Keep the spindle lock button (16) depressed and rotate the blade until the spindle lock engages.
Loosen and remove the blade retaining screw (11) by turning the hex wrench (15) counterclockwise ( Figure H ).
Remove the outer washer (10).
Place the saw blade (5) onto the spindle shaft, making sure that the arrow on the blade points in the same direction as the arrow on the upper guard of the tool.
Fit the outer washer on the spindle with the larger flat surface against the blade.
Insert the blade retaining screw into the hole in the spindle.
Securely tighten the blade retaining screw by turning hex wrench clockwise to tighten the blade retaining screw.

REMOVING THE BLADE

Loosen and remove the blade retaining screw (11) by turning it counterclockwise using the hex wrench (15).
Remove the outer washer (10).
Remove the saw blade (5).

NOTICE: Never engage the spindle lock while the saw is running. Never turn the saw on while the spindle lock is engaged. Severe damage to the saw may result.

WARNING: To reduce the risk of serious personal injury, read, understand and follow all important safety warnings and instructions prior to using tool.

GENERAL CUTS (IMPORTANT: READ SAFETY WARNINGS AND INSTRUCTIONS. )

GUARD AGAINST KICKBACK

With unit unplugged, follow all assembly, adjustment and set up instructions.

Make sure lower guard operates. Select the proper blade for the material to be cut.

Measure and mark work for cutting.
Support and secure work properly (See Safety Rules and Instructions).
Use appropriate and required safety equipment (See Safety Rules).
Secure and maintain work area (See Safety Rules).
With plug inserted and guard closed, make sure switch turns saw on and off.

WARNING: It is important to support the work properly and to hold the saw firmly to prevent loss of control which could cause personal injury. Figure C illustrates proper hand position.

Operation Operation

SWITCH

To operate the tool, depress the trigger switch (1). The tool will continue to run as long as the trigger is depressed.
To turn the tool off, release the trigger switch (1). There is no provision for locking the tool on, and the switch should never be locked on by any other means.

LASER LINE (BDECS 300 ONLY)

WARNING: LASER RADIATION. Never aim the beam at a workpiece with a reflective surface. Bright shiny reflective sheet steel or similar reflective surfaces are not recommended for laser use. Reflective surfaces could direct the beam back toward the operator.

DANGER: LASER RADIATION. AVOID DIRECT EYE EXPOSURE. Do not stare into the laser light source. Never aim light at another person or object other than the workpiece. Laser light can damage your eyes.

WARNING: DO NOT use tinted glasses to enhance the laser light.
Tinted glasses will reduce overall vision for the application and interfere with the normal operation of the tool.

TO USE THE LASER LINE

Mark the line that you intend to cut on the workpiece.
Adjust the depth and angle of cut as required.
Depress the saw trigger switch (1) to project the laser beam (Figure J). Allow the blade to reach maximum speed.
Place the saw shoe on the workpiece. Align the laser line with the mark on the workpiece and slowly push the saw forward, keeping the laser line on the mark.

ADJUSTING THE LASER LINE

Before making a cut, make sure the laser line (8) is accurate. The laser should line up in the right notch (17) of the shoe. When the saw is beveled, the laser should line up in the left notch (18) as shown in the inset of Figure K.
If the laser needs to be adjusted, use a screwdriver to rotate the screw (19) back and forth until the laser lines up properly (Figure K).

CUTTING OPERATIONS

WARNING: To reduce the risk of serious personal injury,always hold the tool with both hands.

After switching the tool on, allow the blade to come up to full speed before starting to cut
Apply only a gentle pressure to the tool while performing the cut.
Always keep bottom surface of shoe in full contact with the workpiece.

HINTS FOR OPTIMUM USE

To minimize splintering of the finished surface of the workpiece material, cut the material with the finished surface on the underside.
To minimize splintering on finished surfaces when the finished surface cannot be placed on the underside, such when cutting laminates, securely clamp a sacrificial piece of plywood to the finished surface and cut through both materials

RIPPING

Accessory rip fences are available for this circular saw.
Ripping is the process of cutting wide material into narrower strips, cutting along the grain of the material. Use an accessory rip guide or clamp a straight edge to the material to act as an guide when making rip cuts.

POCKET CUTTING – FIGURE L

HINTS FOR OPTIMUM USE

WARNING: Never tie the blade guard in a raised position. Never move the saw backwards when pocket cutting.
This may cause the unit to raise up off the work surface which could cause injury.
A pocket cut is one that is made in a floor, wall, or other flat surface.

Adjust the shoe (4) so the blade cuts at desired depth.
Tilt the saw forward and rest front of the shoe on material to be cut.
Using the retracting lever (7), retract lower blade guard to an upward position. Lower rear of shoe until blade (5) teeth almost touch cutting line.
Release the blade guard (its contact with the work will keep it in position to open freely as you start the cut). Remove hand from guard lever and firmly grip secondary handle (3), as shown in Figure L. Position your body and arm to allow you to resist kickback if it occurs.
Make sure blade is not in contact with cutting surface before starting saw.
Start the motor and gradually lower the saw until the shoe rests flat on the material to be cut. Advance saw along the cutting line until cut is completed.
Release trigger and allow blade to stop completely before withdrawing the blade from the material.
When starting each new cut, repeat as above.

WRENCH STORAGE

The hex wrench can be stored on the cord as shown in Figure M.

HINTS FOR OPTIMUM USE

MAINTENANCE

WARNING: Unplug tool before installing or removing accessories, before adjusting, or when making repairs. Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

LUBRICATION
BLACK+DECKER tools are properly lubricated at the factory and are ready for use.

ACCESSORIES
Rip fences and other accessories are available from BLACK+DECKER Service Centers. To find your local service location, call: 1-800-544-6986 or visit www.blackanddecker.com

Recommended accessories for use with your tool are available from your local retailer.

WARNING: The use of any accessory not recommended for use with this tool could be hazardous. Use only 7-1/4 “ (184mm) blades with 5/8” diameter arbor.

SERVICE INFORMATION
All BLACK+DECKER Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the BLACK+DECKER location nearest you.

To find your local service location, call:
1-800-544-6986 or visit
www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a BLACK+DECKER owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required.
This warranty does not apply to accessories.
This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province. Should you have any questions, contact the manager of your nearest BLACK+DECKER Service Center. This product is not intended for commercial use.

Free Warning Label Replacement: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

TROUBLESHOOTING

Problem

| Possible Cause|

Possible Solution

---|---|---

Unit will not start.

|

Cord not plugged in.
Circuit fuse is blown.

|

Plug tool into a working outlet.
Replace circuit fuse. (If the product repeatedly causes the circuit fuse to blow, discontinue use immediately and have it serviced at a BLACK+DECKER service center or authorized servicer.)
Circuit breaker is tripped.

|

Reset circuit breaker. (If the product repeatedly causes the circuit breaker to trip, discontinue use immediately and have it serviced at a BLACK+DECKER service center or authorized servicer.)
Cord or switch is damaged.

|

Have cord or switch replaced at BLACK+DECKER Service Center or Authorized Servicer

For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK+DECKER help line at 1-800-544-6986.