pTron 35DB Studio Ultima ANC Over Ear Headphones User Guide
- June 14, 2024
- pTron
Table of Contents
35DB Studio Ultima ANC Over Ear Headphones
User Guide
35DB Studio Ultima ANC Over Ear Headphones
Important: p Tron ‘Studio Ultima’ is set at 50% default volume. You can
increase the volume through the headset or through the connected device.
TO CHARGE THE CHARGING CASE
i. Connect the charging cable to the headset’s charging port.
ii. Connect the other end of the cable to a USB power source (e.g., computer,
wall adapter).
iii. The LED indicator will show a charging status ( red while charging and
blue when fully charged).
POWER ON/OFF
i. Press and hold the power button for a few seconds to turn the headset on or
off.
Pairing with Devices:
i. Turn on the headset, the headset will automatically go to Bluetooth mode,
and LED indicator red & blue flashes rapidly.
ii. Turn on the Bluetooth on your device, and search “ p Tron BT”
iii. Tap “p Tron BT” to connect. Headset will respond with a voice prompt: ” p
Tron BT connected.”
iv. When the Bluetooth signal is lost, the headset will respond with a voice
prompt “DISCONNECTED” and will shut down automatically after 5 minutes.
v. When the headset power on, the headset will connect to the last paired
device automatically. If not, please repeat the above steps.
Basic Operation:
i. Power on/off: Turn on/off the headset by long press the power button.
ii. Volume control: Press one time “+” button to increase the sound and Press
one time “-” to decrease the sound.
iii. Play/Pause: Press the power button once to start or pause audio playback.
iv. Next/Previous track: Long press the “+” & “-” buttons to move to the next
& previous track when playing music.
v. Mode Button : Press the Mode button to change the headset mode ( Normal
Mode and ANC mode)
Call Control:-
i. To Answer A Call: Press the power button once.
ii. To End A Call: Press the power button once.
iii. To Reject A Call: Long press(2 to 3 sec) the power button
iv. To Redial A Call: Press the power button twice.
Voice Assistant: Press 3 time power key to activate default smart voice
assistant. The respective voice assistant screen pops up on the connected and
you may place your command.
Tips: You may try out the following commands Wired Connection(3.5mm
Aux):
i. To use a wired connection, connect one end of the 3.5mm audio cable to the
headset AUX IN port
ii. Connect the other end of the audio cable to the headphone jack of your
audio source (phone, tablet, computer, etc.).
Troubleshooting:-
Scenario 1 : Connectivity Issue
a. Turn OFF the Headset and charge 100%.
b. Unpaired with the connected Bluetooth device.
c. Restart the Bluetooth device.
d. After 100% charging switch ON the Headset and pair it with the Bluetooth
device again..
Scenario 2 : Headset Disconnecting During a Phone Call
a. Headset must be 100% charged before using (low battery can also cause call
drops).
b. Unpair the Headset with your connected device and restart the device.
c. Pair the Headset again.
Important: Please use this Headset within a 10 metre wireless range from
the connected device.
Safety Precautions
- Keep the device out of extreme heat and humidity.
- Play time may vary depending on personal habits,
- Using incompatible USB cable or high voltage chargers can damage the product & void the product
- warranty. We strongly recommend using a good quality DC5V-1A chargers & the USB cable included in the package.
- Please don’t over-charge the product as it will decrease the service life of battery.
- Read all warnings on the product and in the operating instructions.
- It is recommended to utilize the product below the maximum volume in order to protect hearing and extend headset service life.
- Please don’t open/temper the product or product’s battery.
- Please keep the product out of children’s reach.
- Stop using this product immediately if it causes discomfort or pain.
- Dispose the product responsibly and adhere to your local authority guidelines.
Packing Box Content
- Headset, 1 USB Type-C charging cable, 1 Aux cable & 1 User Manual/Warranty QR Card
What is Covered in Warranty?
- Manufacturing defects in materials and workmanship of the product ONLY. This warranty applies when the product is used under normal conditions and the purpose for which the product was designed.
- No warranty on product accessories such as aux cable, small charging USB cables.
- To avail warranty, Product Registration is Mandatory at https://ptron.in/apps/product-registration
- Please read through the complete warranty details at https://ptron.in/pages/repair-service-warranty
Customer Care Details:
Mail: support@ptron.in
Tel: 040 – 67138888
Service Centers List: https://ptron.in/pages/ptron-service-centers
Disclaimer: The colour and specifications shown in or mentioned in the user
manual may differ from the actual product. Images shown are for representation
purposes only. Other product logos and company names mentioned herein may be
trademarks or trade names of their respective owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>