HIFI WALKER V6 64GB Digital Voice Recorder User Manual
- June 14, 2024
- HIFI WALKER
Table of Contents
HIFI WALKER V6 64GB Digital Voice Recorder
Packing List
- lx Voice recorder
- lx USB cable
- lx User manual
Button Introduction
Button Function
- Previous track key: Go back/Up (Long press for fast rewind)
- Next track key: Go forward/Down (Long press for fast forward)
- Volume+ key: Increase volume
- Volume – key: Decrease volume
- M Menu key: Confirm/Menu
- Stop key: Stop/Save recording/Back
- Recording indicator
- Display screen
- Recording key: Start recording
- Play key: Play/Pause
- External speaker
- Headphonejack
- External microphone/LINE-IN port
- USB port
- Power switch: On/Off
- Omnidirectional microphone
Display Description
- Total track count display
- Dynamic recording level display
- Recording status display
- Remaining recording time display
- Battery level display
- The current recording time display
- Recording format and bit rate display
- Noise reduction level display
Basic Operations
Power on/off
- Power On: Slide the power switch of the voice recorder upward to the “ON” position, and the recorder will power on.
- Power Off: Slide the power switch downward to the “OFF” position, and the recorder will power off.
Recording/Saving Recording
- Start Recording: In the powered-on state, press the recording key shortly to enter the recording mode. The recording timer starts, and the recording indicator blinks.
- Pause Recording: During recording, press the “Play” key shortly to pause the current re-. cording The recording indicator stays on. Press the “Play” key again to continue the recording.
- Save Recording: During recording, press the “Stop” key shortly to stop the recording and save the current recording file.
Play/Pause
In the recording or music mode, press the “Play” to start playback, and press
it again to pause.
Track Change/Fast Forward and Rewind
In playback mode, press the “Previous Track” key or “Next Track” key to switch
tracks, or long press it again to pause.
Volume Adjustment
In the stopped or playing state, press the “Volume+” key to increase the
volume, and press the “Volume -” key to decrease the volume.
A-B Repeat
In voice or music playback mode, long-press the “M Menu” key to set the
starting point “A” of the A- 8 repeat. The screen will display “A-8” and blink
Long-press the “M Menu” key again to set the ending point “B.” The screen will
display “A-8” and stop blinking, indicating that the A-8 repeat function is
set To cancel the A-8 repeat, longpress the “M Menu” key again.
Return
In voice or music playback mode, short-press the “Stop” key to stop the
current playback and return to the playlist. In the menu state, shortpress
the “Stop” key to return to the previous menu. Long-press the “Stop” key in
any state (except the main interface) to directly return to the main
interface.
Recording settings
After selecting the “Recording” function menu on the main screen, press the “M
Menu” button to access the recording menu. Press the “Previous Track” or
“Next Track” button to choose and enter the recording settings, which include
70 options:
Recording Source
- There are two recording sources available on the device:
- Microphone: This mode uses the built-in microphone or an external microphone.
- LINE-IN Recording: This mode allows recording from an external audio source connected through LINE-IN.
- Recording Format : You can choose between two recording formats: WAV and MP3. Each format has different available bitrates.
- Recording Bitrate : The recording bitrate options depend on the selected recording format. For WAVformat: 572Kbps, 768Kbps, 7024Kbps, 7536Kbps. For MP3 format: 32Kbps , 64Kbps , 728Kbps.
- Recording Gain: There are seven levels of recording sensitivity. Select the appropriate level and press the “M Menu” button to confirm. Higher levels allow for recording from a greater distance.
- Recording Monitor: You can enable or disable recording monitoring. Press the “M Menu” button to confirm. Use the “Previous Track” or “Next Track” button to select “Open Monitor” or “Close Monitor” and confirm with the “M Menu” button.
- Voice Activation (Sound Control) Settings : To enable voice-activated recording, select “Sound Control Settings” after entering the recording menu. You can adjust the sound control switch and sensitivity level (1 to 7) for voice-activated recording based on the ambient noise level.
- Segmented Recording: Segmented recording allows you to set the duration of each recording segment. Options include “Off,” 30 minutes, 60 minutes, 90 minutes, and 120 minutes. Press the “M Menu” button to confirm your selection.
- Timed Recording : You can set up scheduled recording by selecting “Timed Recording” within the recording settings. Configure the switch, recording period, start time, and end time for timed recording.
- Recording Indicator Light : You can enable or disable the recording indicator light based on your preferences.
- Noise Reduction Level: There are four options for noise reduction: “Off,” “Levell,” “Level 2,” and “Level 3.” Choose the appropriate level based on your preferences.
- Noise Reduction Level: There are four options for noise reduction: “Off,” “Levell,” “Level 2,” and “Level 3.” Choose the appropriate level based on the ambient noise level and confirm by pressing the “M Menu” button. Note that noise reduction is available in mono mode, and disabling it will enable stereo mode.
Music Playback
After selecting the “Music” menu on the main screen, press the “M Menu” button
to confirm and access the music menu. Use the “Previous Track” or “Next Track”
button to select the desired song and press the “Play” button to start
playback.
Playback Settings
In music or voice playback mode, press the “M Menu” button to access the
playback settings menu, which includes the following options: (7) Playback
Settings: Select “Playback Settings” and enter the menu to access three sub-
menus: Sound Settings, Repeat Settings, and Playback Modes.
Sound Settings:
-
Variable Speed Playback (Varispeed): Enter the Varispeed menu and press the “Volume+” button to increase playback speed or the “Volume-” button to decrease it. Press the “M Menu” button to confirm your choice. Note that lossless music does not support variable speed playback.
-
Equalizer (EQ): Enter the EQ menu and choose from options such as “Sound Off,” “Rock,” “Funk,” “Hip Hop,” “Jazz,” “Classical,” and “Electronic.” Press the “M Menu” button to confirm your choice.
Repeat Settings: -
Interval Repeat: Set the time interval between A repeat points, ranging from l to 10 seconds. Press the “Volume+” or “Volume-” button to adjust the interval time and press the “M Menu” button to confirm.
-
Repeat Count: Set the number of repeats for A repeat, ranging from l to 10. Press the “Volume+” or “Volume-” button to adjust the repeat count and press the “M Menu” button to confirm.
-
Repeat Mode: Enable A-B repeat by choosing the Repeat Mode menu. When activated, the A-B points will appear on the playback screen, and you can set point “B” by pressing the “Next Track” button. The screen will display “A-B” and stop flashing, indicating a successful A-B repeat setup.
Playback Modes:
- Random Playback: Enable or disable random playback on the device.
- Repeat Playback: Choose from options like “Browse Playback,” “All Repeat,” “Single Repeat,” or “Repeat Off.”
- Single File Delete: You can delete the currently playing or paused music/voice file. Select “Single File Delete,” and the system will prompt whether to delete the current file. Choose “Yes” and confirm the deletion.
- AII File Delete: You can delete all files currently in the playback state. Select “All File Delete,” and the system will prompt whether to delete all files. Choose “Yes” and confirm the deletion.
- Add to Playlist: Add the currently playing or paused music to one of the three available playlists. Create personalized playlists by adding your favourite songs.
- Remove from Playlist: Remove the currently playing or paused music from one of the playlists.
Connect to computer
To download and upload files from the computer, please use the USB cable
provided with the device. Connect the larger end of the USB cable to the PC’s
USB port and insert the smaller end of the USB cable into the USB port of the
device. Once connected, the device will automatically power on. Upon the first
connection, the computer may prompt to create a driver information library and
detect new hardware. The device will be automatically detected by the
computer, indicating a successful connection.
Charging The device is equipped with a builtin lithium battery, and you can
charge it by connecting it to the computer using the provided USB cable.
During charging, the battery icon will cycle, and when the battery is fully
charged, the full battery icon ( ) will be displayed. It takes approximately
.5 hours to fully charge the built-in lithium battery.
Note: If using an adapter for charging, please use a charger with a maximum output of SV and.
System settings
Auto Shutdown
Auto shutdown is a feature that forcefully powers off the device during recording or playback. Press the “Previous Track” or “Next Track” button or rotate the multifunctional knob to select auto shutdown or set the auto shutdown time. You can choose from 70 minutes, 30 minutes, 60 minutes, 90 minutes, or 720 minutes. Press the “M Menu” button to confirm your selection.
(Note: Auto shutdown is effective for a single use only).
Backlight Timer
The backlight timer provides options for 10 seconds, 20 seconds, 30 seconds,
or “Always On.” When there is no key operation, the device will activate the
screen saver to save power according to the set time.
Backlight Brightness
In the backlight brightness menu, press the “Volume+” or “Volume-” button to
adjust the backlight brightness level. Once you’ve selected the desired
brightness, press the “M Menu” button to confirm.
Date and Time:
Press the “M Menu” button to enter the date and time setting menu. Use the
“Previous Track” or “Next Track” button to choose between time setting and
date setting. For time setting, use the “Volume+” or “Volume-” button to
adjust the time value, and use the “Previous Track” or “Next Track” button to
switch between hours and minutes. Press the “M Menu” button to confirm and
exit. For date setting, use the “Volume+” or “Volume-” button to adjust the
date value, and use the “Previous Track” or “Next Track” button to switch
between year, month, and day. Press the “M Menu” button to confirm.
Language Selection:
The device supports multiple languages, including Chinese, English, Japanese,
Korean, etc. Select the desired language and press the “MENU” button to
confirm.
Password Setting:
The device supports password locking. Press the “M Menu” button to enter the
password setting menu. You can set the password switch to open and modify the
password. Password Switch: To use the password feature, you must set the
password switch to open. The password feature will only be effective when the
password switch is open. Password Setting: After setting the password switch
to open, you can set the startup password. Use the “Previous Track” or “Next
Track” button to switch between password rows. Use the “Volume+” or “Volume-”
button to set the numeric value. Once the password is set, press the “M Menu”
button to confirm.
Note: Please remember your password. If you forget the password, enter “181818” at the password input screen after startup, and then longpress the “Stop” button to cancel the password and enter the main interface forcefully.
Information
This section provides details about the software version and disk space.
Format Device:
Press the “M Menu” button to enter this menu, and then choose whether to
confirm formatting. Press the “MENU” button to confirm and start formatting.
(Note: Formatting will erase all data, so please remember to back up im-
portant files).
Factory Reset:
This option allows you to restore the device to its factory settings. Press
the “M Menu” button to confirm the factory reset.
Technical specification
Item Name | Digital Voice Recorder |
---|---|
Brand | HIFIWALKER |
Model | V6 |
Dimension | 70l.Smmx32mmx72.Smm |
Display screen | 7-inch TFT true color display Resolution: 728 x 96 |
USB
interface
| TYPE C USB2.0
Storage| Built-in 64GB TF card
Battery| 3.7V/450mAh Polymer Battery
Recording formats| WAV/MP3
Recording bitrate
| WAV:Sl2Kbps/768kbps/ 7024kbps/7S36kbps
MP3:32kbps/64kbps/728kbps
Audio formats| MP3 WMA WAV APE FLAC
Support compression rate
| WAV supports up to 24BIT 48KHz
APE/FLAC support up to 76BIT 48KHz
Continuous recording time|
Approx. 20 hours (Screen Saver/ Noise Reduction On/WAV S72K)
Continuous playback time
|
Approx. 35 hours (screensaver/ headphone playback/volume 20/ lossless music)
Battery charging time|
Approx. 2 hours (using a SV
7000 mA charger)
Signal-to noise ratio|
93dB
Headphone output
| Stereo Output
External audio output|
Supports external audio playback
Operating tempera- ture|
-S to 40 degrees Celsius
Net weight| Approx. 75g (including battery)
Supported Operating Systems|
windows xp/vista/windows 70
Frequently Asked Questions
How to record and play back recordings?
To start recording, please turn on the voice recorder by pushing the power
button (located on the left side) to the “ON” position. Press the “REC” button
to begin recording. Press the “Stop” button briefly to stop recording and save
the current recording file. Press the “Play” button to play the recording
file, and press the “Play” button again to pause playback.
How to fast forward/rewind during playback?
In playback mode, press and hold the up/down buttons to fast forward or
rewind.
How to adjust the volume?
In playback mode, press the volume buttons briefly (do not hold the volume
button). and then press the up/down buttons to adjust the volume. The current
volume value will be displayed in the upper right corner of the screen.
How to set a password?
To set a password, open the voice recorder, go to Settings»> find “Password
Setting” using the up/ down buttons»> turn on the password switch »> set the
password»> enter your password.
Forgot the password?
If you forget the password, enter the password “181818”, then press and hold
the “Stop” button to unlock the voice recorder. After that, you can re-enter
the voice recorder and set a new password.
How to reset the voice recorder after it crashes?
In the event of a crash, press and hold the playback button for 73 seconds to
initiate an automatic system reset.
How to Turn ON Voice Operated Recording Mode (Voice Activated Function)?
To enable Voice Operated Recording Mode (also known as Voice Activated
Function), follow these steps: Select the “Recorder” function on the main
interface. Press the “M Menu” button to access “Record settings.” Briefly
press the “Previous Track” or “Next Track” button to choose “VOR mode.” In
this menu, you’ll find two options: “Switch” and “Sensitivity level.” To use
the voice control recording function, set the “switch” to the “On” position.
In this mode, the recording will be voice-activated, and you can adjust the
sensitivity level based on the ambient noise. There are 7 sensitivity levels
available, ranging from 7 to 7, with higher levels indicating greater
sensitivity.
The voice recorder can be connected to the computer, but it can only charge
and cannot read the disk.
Possible reasons are as follows: A) The Type-C USB cable is damaged or the USB
socket is loose. If so, try using another USB cable (such as your Android
phone cable) connect to another USB socket, or simply restart your computer.
B) Check if the voice recorder’s power switch is in the OFF position when
connecting to the computer. C) There may be a problem with the device. If it
is a quality issue, we can provide replacement services.
How to set the date and time?
Go to “Settings” »> use the up/down buttons to find “Date and Time Setting”>
Set the time/date as desired.
The voice recorder cannot play the recording on the computer.
This may be due to a problem with the media player. Try using another media
player, such as VLC Media Player (Website: http://www.videolan.org/) for Mac
users, or choose “Windows Media Player” for Windows users.
can’t find my recording in the voice recorder.
This may be because the device is reading the “Music” folder. Long press the
“Back/Save” button to switch to the “Recording” folder, where you will find
the recording files. Alternatively, connect the voice recorder to the computer
and check if there are any recording files.
How to use the Recording monitor function?
To utilize the Recording monitor function, follow these steps: Select the
“Recorder” function on the main interface. Press the “M Menu” button to
access “Record settings.” Briefly press the “Previous Track” or “Next Track”
button to choose “Recording monitor.” Press the “M Menu” button to toggle
between the “ON” and “OFF” interfaces. When you select “ON,” you’ll be able to
listen in realtime while recording (this requires plugging in headphones and
enabling the recording function).
Why is the actual capacity of a TF card smaller than the labelled
capacity?
The system software occupies a portion of the device’s space, resulting in a
slight difference from the nominal capacity, which is a normal phenomenon.
Scan QR & Download User Manual
- Website: www.hifiwalker.com
- Facebook: @HIFIWALKER.official
- Youtube: HIFI WALKER
- Email: Support@hifiwalker.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>