JWX SJZBD16 Standing Gaming Desk Installation Guide

JWX SJZBD16 Standing Gaming Desk

Product Information

• Product Name: SJZBD16
• Product Type: Screw Accessories
• Note: The actual number of screws may exceed the mentioned quantity in the instructions.

SCREW ACCESSORIES

Note: The actual number of screws will be more than what is mentioned in the instruction.

PARTS ACCESSORIES

INSTALLATION

1. Connect two crossbars “A” with “P”.
2. Insert the motor axle “C”, and rotate “C” to fix it.
3. Insert the motor axle to “D”, and rotate it counterclockwise to lower the desk legs to the lowest height.
4. Disassemble “D”
5. Install motor “E”
6. Install “C” to another desk leg “L”.
7. At the same, insert the motor axle to “D”, rotate it clockwise to lower the desk legs to the lowest height.
8. Connect the two motor axles by using “D”.
9. Assembly the crossbar “A” with desk legs.
10. Install fixed iron plate “B”
11. Fix crossbar “A” with screws.
12. Fix connector “D” with screws
13. Assembly desk legs.
14. Assembly the pads
15. Assembly desktop holder
16. Connect the desktop.
17. Connect the desk frame and desktop.
18. Tighten the screws.
19. Assemble the controller.
20. Assemble the adapter
21. Assemble the cup holder and headphone holder
22. Assembly of the LED light.
23. Connect the controller with an adapter.
24. Connect the controller to motor
25. Fix the cable by using cable management.
26. Assembly cable management tray.

Side

Middel

Instructions for using the control box

Key Introduction

Up and down key operation

• When pressing and holding the “UP” key for 3 seconds, the desktop automatically runs upward to the highest point, press any key to stop running.
• When holding down the “DOWN” key for 3 seconds, the desktop runs down to the lowest point, press any key to stop running.
• When the “UP” or “DOWN” key is pressed briefly, the desktop runs a small distance accordingly to achieve point movement.

SITTING / STAND key operation

• Sit or stand position modification: When running to sit or stand at the appropriate height position, long press the “SITTING / STAND” key, until the digital numbers flash, then the corresponding position is modified successfully.
  Sitting or standing position run short press the “SITTING / STAND” key, digital tube flashing height 2S,

• the desktop automatically runs to the height of the memory position, running, any key can stop running.

Zero position reset

• Please do this first after the table is installed or if you encounter a malfunction during use
• Press and hold “RESET” 3S and wait for the controller operation indication to flash “- – -“, enter into the reset mode, the desktop automatically runs, and wait for the end of the reset process.

Stand and sit reminder (countdown method)

• Countdown time: provides 3 levels of time, T30 = 30 minutes, T45 = 45 minutes, T60 = 60 minutes.

• Start the countdown timer: Short press “REMINDER” and the display shows T30/T45/T60 in turn, the countdown timer starts.
  Exit countdown:

  • short press “REMINDER” until the display shows the height figure.
  • the timer is turned off after the countdown interval

Attention:

• This product is only applicable to lift table desks, please do not use it for other purposes.
• Before use, please make sure the power supply voltage is under the voltage range indicated on the product label.
• Do not use it in places prone to oxidation and corrosion.
• Do not use at high temperatures or in the sun, indoor use only.
• Do not disassemble the product for non-professional personnel to prevent the risk of electric shock.
• The relevant after-sales service is carried out by the manufacturer or authorized service representative.

Light use instructions

Key operation

• Light mode switch: press the touch button to switch modes, each time you press the light will switch to a different mode.
• Light off and on  long press the touch button for about 3 seconds to achieve the light off and on

Functional features.

• 6 built-in musical effects, 6 static color effects, and 4 regular non-musical pattern dynamic effects.
• With power-down save current mode function.
• With a touch button to switch the light mode as well as the switch function, easy to operate.
• Output of the dual circuit light interface.
• Direct power supply using the Micro USB interface.
• With high-gain pickups to pick up ambient music and realize music with moving light effects to visualize music.

Parameters

• Input voltage: DC 5V
• Input current: 500mA
• Power: 2.5W

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>