U-tec ULTRALOQ U-Bolt Pro Smart Lock Bridge WiFi Adaptor Installation Guide
- June 14, 2024
- U-tec
Table of Contents
U-tec ULTRALOQ U-Bolt Pro Smart Lock Bridge WiFi Adaptor
Important Notes
- Do not use a power drill for installation.
- Install and test the lock with the door open to avoid being locked out.
- Please read all the instructions before contacting customer support.
- Please contact customer support before returning the product to the store.
- DO NOT install the batteries before installing the lock!
- Follow the instructions in sequential order!
- This lock is designed for the following operating temperatures: Outside Lock Body: -31° F(-35°C) to 158° F (70°C) Inside Lock Body: 14° F (-10°C) to 131° F (55°C)
- Please use an AA Alkaline Battery and don’t use a Lithium Battery or Rechargeable Battery.
Statements
To ensure the best service, please register your account at www.u-tec.com/register.html
ULTRALOQ Terms & Policies
Before using all ULTRALOQ products, please read all applicable terms, rules, policies and usage provisions found at www.u-tec.com/company/privacy. By using your ULTRALOQ, you agree to be bound by the U-tec Privacy Policy.
Need Help?
For technical documents and more Please visit
support.u-tec.com
Packing List
Installation Guide
Installation Video
Please scan this QR code to watch the easy step-by-step installation video before attempting to install ULTRALOQ U-Bolt Pro. You can also view the website directly. www.u-tec.com/lock/U-bolt_pro/guide
Preparing Door Check the door’s dimensions.
Step1
Measure to confirm that the door is between P/a”~ 1¾” (35 mm- 45 mm) thick.
Step2
Measure to confirm that the diameter of the hole is 21/a” (53 mm) or ½” (38
mm)
Step 3
Measure to confirm that the backset is either 2 % “or 2 W’ (60 mm or 70 mm).
Step4
Measure to confirm that the diameter of the hole in the door edge is 1″ (25
mm).
Steps 5
Measure to confirm the depth of the hole in the frame is at least 1″(25mm).
If you have a new door, please drill the holes according to the Drill Template.
INSTALLATION INSTRUCTION
Installing Bolt and Strike
Step1
Install a Bolt into the door. Make sure the UP t icon goes up.
Note: Bolt is set for 2 %” backset initially. It can be adjusted to 2 ¾” if needed. To adjust it please make sure the bolt is retracted, then, press it, twist and pull it or push it to your desired length.
Step2
Install Strike into the door frame.
Installing Exterior Assembly
Step1
Keep the Bolt retracted and the cylinder tailpiece horizontal. Install
Exterior Assembly. Please do not insert the mechanical key during
installation.
Step2
Align its two sticks with two holes on Bolt. The cable goes through the hole
below Bolt.
If your door has a 1 ½”(38 mm) borehole, remove the spacer as shown.
Installing Interior Assembly Mounting Plate
Step1
Route the cable through the hole on the Interior Assembly Mounting Plate.
Step2
Secure Interior Assembly Mounting Plate to Exterior Assembly using Screws
D.
Installing Interior Assembly
Step1
Remove the battery cover of the Interior Assembly.
Step2
Insert the connector of the cable into the socket on the Interior Assembly.
Press the connector in firmly until it is completely seated.
Step3
Rotate the knob and keep it in a vertical position to stay unlocked.
Step4
Attach Interior Assembly to Mounting Plate and tighten 2
Installing the Batteries and Performing the Door Handing Process
This step will teach your lock the orientation of your door and is crucial to lock operation.
Step1
Rotate the knob and keep it in a horizontal position to stay locked.
Step2
Insert 4 AA Alkaline Batteries.
Note: Anytingerprint or code can unlock U-Bolt Pro in Factory Default Mode.
Step 3
Install battery cover.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>