Heckler H891 AV Credenza Mini for Video Conferencing Meeting Rooms User Guide

Heckler H891 AV Credenza Mini for Video Conferencing Meeting Rooms

In the box

• A. 1 x main body (R502-1)
• B. 1 x front panel (R509)
• C. 1 x mounting bracket for Rally Bar & Rally Bar Mini (R502-2)
• D. 2 x mounting bracket for Google Meet Series One Room Kit Audio Bar (R502-3)
• E. 1 x wall-mounting template (K394)
• F. 2 x mounting screw for camera brackets (F036)
• G. 2 x mounting screw for Rally Bar & Rally Bar Mini (F038)
• H. 2 x mounting screw for Google Meet Series One Room Kit Audio Bar (F775)
• I. 1 x hex key for installing camera brackets (F776)
• J. 1 x set screw for mounting PTZ cameras (F040)
• K. 1 x wingnut for mounting PTZ cameras (F041)
• L. 1 x spacer for mounting PTZ cameras (F042)
• M. 4 x screw for mounting VESA-compatible NUCs (F869)
• N. 4 x thumb nut for mounting VESA-compatible NUCs (F838)
• O. 4 x drywall-mounting screw (F039)
• P. 4 x drywall-mounting washer (F035)
• Q. 4 x drywall-mounting spacer (F034)
• R. 4 x drywall-mounting wall anchor (F037)
• S. 5-foot roll of hook & loop strap (F947)
• T. 5 x strapping buckle (F751)
• U. 2 x key (F033)
  Keys for all Heckler AV Credenza Mini’s are identical and interchangeable.

Tools needed

• Power drill
• 1/2-inch drill bit
• Philips screwdriver
• Masking tape
• Level
• Tape measure
• Stud finder

Install wall anchors

Tape the wall-mounting template(E) to the wall. Use a level.

• We recommend mounting the credenza with its top surface at 36 inches above the finished floor (AFF). This aligns the credenza well with wall outlets at 18 inches AFF.
• Mark the locations of wall studs on the mounting template.
• The weight of AV Credenza Mini does not require mounting to wall studs. The wall-mounting hole pattern is designed to enable you to mount the credenza to your preferred wall location while mounting exclusively to drywall.
• Mark the hole locations on the wall. Select one hole location for each corner of the credenza.
• Remove the template from the wall.
• Drill holes in the drywall. Use a 1/2-inch diameter drill bit.
• Install the wall anchors(R).

How to install a Snaptoggle wall anchors

Pass the wall mounting screws(O) and washers(P) through the white nylon spacers(Q), then fasten loosely into the wall in the upper left and upper right mounting positions.

Do not fully tighten the screws during this step.

Mount devices and cabling

You can mount devices and cabling before or after mounting the credenza to the wall

• Cut the provided hook & loop straps(S) to length as you needed for strapping components and cable management.
• Use buckles(T) to firmly strap components.
• Strap components to the grid of large rectangular holes on the rear and bottom surfaces of the credenza body.
• Fasten NUCs and other VESA-compatible devices to the VESA-compatible M4 clearance holes located between the large rectangular hole. M4 mounting hardware included(M and N).

Install credenza body

Hang the credenza on the top two anchor screws.

• Fasten mounting screws(O) and washers(P) through the lower corners of the credenza body. Position a white nylon spacer(Q) between the body and the wall in each lower corner.
• Do not tighten the mounting screws.

Install camera bracket for Logitech Rally Bar & Rally Bar Mini

• Fasten the bracket(C) to Rally Bar with the 1/4-20 screws(G) and key(I) provided.

• Fasten mounting screws(F) to the bracket with key(I) provided. Do not tighten the screws at this step.

• This is a good opportunity to connect all cables to the Rally Bar and install its rear hatch.

• Slide the bracket’s mounting screws into the horizontal keyhole slots on the back wall of the credenza.

• Tighten the screws with the provided hex key(I).

Install camera bracket for Google Meet Series One Room Kit

• Fasten the pair of Google Meet mounting brackets(D) to the Google Meet Audio Bar with provided screws(H) and hex key(I). the upper corners of the main body. Position each bracket so the cork liner rests on the top surface of the credenza body.

• Fasten mounting screws(F) to the bracket with key(I) provided. Do not tighten the screws at this step.

• Slide the bracket’s mounting screws into the horizontal keyhole slots on the back wall of the credenza.

• Tighten the screws with the provided hex key.

Install camera bracket for PTZ cameras

• Use the slot on the top surface of the credenza for mounting cameras with 1/4-20 mounting holes on their bottom surface.
• Fasten the provided 1/4-20 set screw(J) and black spacer(L) into your camera.
• Place the camera on the top surface. Use the black spacer provided to lift the camera from the top surface a small distance. Fasten the camera to the credenza body with the provided wing nut(K).
• This space enables the front panel to be installed and removed.

Install front panel

• Lower the front panel onto the body. Rest the four posts on the panel onto the four hooks on the main body.

• Use the provided keys(U) to turn the cam lock on the underside of the credenza body.
• Keys for all Heckler AV Credenza Mini’s are identical and interchangeable.
• The locking feature is a low-security feature intended to reduce end-user tampering.

https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini- 1f0d3ded48d24d04aaf6513838651a72

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>