Heckler Design H756 OnWall Mount for iPad 10th Generation Instructions

: September 24, 2024
: Heckler design

Table of Contents

H756 OnWall Mount for iPad 10th Generation
Specifications
Product Usage Instructions
Mounting the Pocket to Your Wall
Determining Installation Height
Reviewing Hole and Slot Patterns
Mounting Options
Installing iPad 10th Generation
Installing PoE Adapter
Connecting Charging Cable (Optional)

H756 OnWall Mount for iPad 10th Generation

“`html

Specifications

Product Name: H756 OnWall Mount for iPad 10th Generation
Included in the Box:
1. 1 x OnWall mount
2. 2 x Drywall anchors (F155)
3. 2 x Drywall anchor screws (F360)
4. 1 x Set Screw Assembly Key (F914)
5. 1 x Enclosure Assembly Key (F529)
6. 1 x Velcro dot set
7. 1 x Cable Tie (F817)

Product Usage Instructions

Mounting the Pocket to Your Wall

Use the fully assembled OnWall Mount as your hole template.

Determining Installation Height

To install your iPad at an ADA-compliant height, position the
enclosure so that the top edge of the iPad screen is no higher than
48 inches above the finished floor.

Reviewing Hole and Slot Patterns

Hold the enclosure to the drywall at the desired installation
height and mark the two screw positions and CAT cable hole position
as shown.

Mounting Options

Option 1: Mount Directly to Drywall

Install drywall anchors provided. Make sure to shut off
electricity in the installation area before drilling holes or
installing hardware.

Option 2: Mount to a US Gang Box

Route your CAT cable through the wall and out through the gang
box.

Option 3: Mount to a European Wall Box

Route your CAT cable through the wall and out through the wall
box.

Installing iPad 10th Generation

Loosen the top, bottom, and side enclosure brackets.
Position the iPad into the enclosure.
Connect the right-angle USB-C adapter & Apple USB-C
cable.
Tighten the enclosure-bracket screws.

Installing PoE Adapter

Install your PoE adapter inside the pocket.
Connect your CAT cable to your PoE adapter.

Connecting Charging Cable (Optional)

Connect the charging cable to PoE if desired.

Frequently Asked Questions (FAQ)

Q: Can I use different hardware for mounting if I feel the

provided hardware is not suitable?

A: Yes, you can source alternate hardware if you feel the
provided drywall anchors and screws are not appropriate for your
wall.

Q: What is the recommended height for installing the iPad on

drywall?

A: The top edge of the iPad screen should not be higher than 48
inches above the finished floor for ADA-compliant installation.

“`

H756 OnWall Mount for iPad 10th Generation

In the box Mount the pocket to your wall
Determine the height of your installation Review the hole and slot patterns on the pocket Hold the enclosure to the drywall at the desired installation height Remove the tablet enclosure from the pocket Option 1: Mount directly to drywall Option 2: Mount to a US gang box Option 3: Mount to a European wall box Install the iPad 10th Generation Loosen the top, bottom, and side enclosure brackets Position the iPad into the enclosure Tighten the enclosure- bracket screws Install your PoE adapter inside the pocket Install the tablet enclosure to the pocket Connect charging cable to PoE(optional) Hang the enclosure on the pocket Tighten the set screws
In the box

a. 1 x OnWall mount b. 2 x Drywall anchors (F155) c. 2 x Drywall anchor screws (F360) d. 1 x Set Screw Assembly Key (F914) e. 1 x Enclosure Assembly Key (F529) f. 1 x Velcro dot set g. 1 x Cable Tie (F817)
Mount the pocket to your wall
Use the fully assembled OnWall Mount as your hole template.
Determine the height of your installation
To install your iPad to your Drywall at an ADA-compliant height, position the enclosure so that the top edge of the iPad screen is no higher than 48 inches above the finished floor.

Review the hole and slot patterns on the pocket
Hold the enclosure to the drywall at the desired installation height
Mark the two screw positions and the CAT cable hole position as shown.

Remove the tablet enclosure from the pocket

0:00 / 0:05
Option 1: Mount directly to drywall
Install drywall anchors.
For safety, shut off electricity in the installation area before drilling holes or installing hardware into your walls.
For your convenience, two drywall-mounting anchors and screws are provided. If you feel this hardware is not appropriate for use with your wall, please source alternate hardware.

Drill the hole for CAT cable.
Route your CAT cable through the wall and out through this hole.

Mount the pocket on the drywall.

0:00 / 0:05
Option 2: Mount to a US gang box
Route your CAT cable through the wall and out through the gang box.

Option 3: Mount to a European wall box
Route your CAT cable through the wall and out through this wall box.

Install the iPad 10th Generation
Loosen the top, bottom, and side enclosure brackets

0:00 / 0:06
Position the iPad into the enclosure
Connect the right-angle USB-C adapter & Apple USB-C cable.

Position the iPad carefully so it does not drop into the screen-cut-out window
of the stand.
0:00 / 0:04

Tighten the enclosure-bracket screws
0:00 / 0:06
Install your PoE adapter inside the pocket

Connect your CAT cable to your PoE adapter.
Install the tablet enclosure to the pocket
Connect charging cable to PoE(optional)