Veise RZ02A Fingerprint Door Lock User Manual

Veise RZ02A Fingerprint Door Lock

TOOL REQUIRED

****Do not use an electric screwdriver during installation

IMPORTANT
Do not load  batteries until lock is completely installed.

INSTALLATION OVERVIEW

Parts List

If any parts are missing or damaged, please contact Customer Support.

Prepare the door and check dimensions

• Measure to confirm that the hole in the door is 2-1/8″ (54mm). Measure to confirm that the hole in the door edge is 1 ” (25mm).

• Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70mm)

• Measure to confirm that the door is 1-3/8″ to 2″ (35 mm or 50mm) thick.

• Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep.

install the latch and strike

• Use a screwdriver to test if deadbolt works smoothly.

• Install strike on the door frame.

Install exterior assembly

• IMPORTANT
  Before installation, make sure the latch is fully retracted (in the unlocked position)

• With the latch fully retracted (in the unlocked position), route the cable below the latch, and insert the torque blade through the slot in the latch.

• Secure the mounting plate with the supplied screws. Do not overtighten screws

Install interior assembly

 Detect left/right hand door installation Reset the lock to teach the

lock the orientation of the door.

• While the door is OPEN and UNLOCKED, load 3 AA batteries into the battery compartment.
• Note
• For long last, please use all new, non-rechargeable Alkaline batteries only. Press and hold the Reset button on the interior assembly by using the reset tool.
• Load the 4th battery and keep holding the reset button for 3 seconds, until you hear the sound of “beep”. The latch bolt will extend to learn the orientation of the door automatically.
• IMPORTANT: This step is required and crucial for the lock to operate properly.

PROGRAMMING INSTRUCTIONS

At a Glance

How to Use

Definitions

• Master Code
  • Required for programming and feature settings. Master code can be used to unlock the door under vacation mode. The default master code needs to be changed before programming. Property owner & manager should keep this information confidential.
• Auto Lock
  • Automatically locks the deadbolt 30 seconds after unlocking. This feature is off by default. You can customize the Auto Lock time delay between 10 and 99 seconds.
• Key Unlock
  • Key Unlock is always available when the batteries are completely dead or valid User Codes are forgotten.
• Low Battery Indicator
  • If you hear 10 beeps along with 10 red light flashing after pressing any key to lock or unlock the door, that’s an alert for replacing batteries. Please replace with 4 brand new AA alkaline batteries and do not mix used and new batteries. All settings are stored in the lock while the batteries are removed and replaced.
• Wrong Entry Limit
  • After 10 unsuccessful attempts at entering an invalid PIN code, the unit will shut down for 3 minutes.
• Silent Mode
  • The beep sounds when pressing keypad can be muted. But you will still hear low battery and system alerts.
• Vacation Mode
  • This is a security feature for you when you are leaving your home for vacation or long trip. Enabling vacation mode will restrict all user codes until master code is entered on keypad. If the lock would be unlocked by the thumb turn from the inside, the lock will sound an alarm.
• One Time User Code
  • This code only can be used once and will be automatically deleted after used.
• Anti-peeping Code
  • User can prevent pin code exposure from strangers by entering random digits before or after pin code.

Code Format

1. Master Code(4 to 10 digits): The default Master Code is II is required that you change ii to a code of your own before programming.
2. User Code: 20 User Codes (4-10 digits), 1 one-time User Code and 20 fingerprints can be programmed and stored in the lock.
3. Both Master Code and User Code don’t support the following combination of numbers.

Quick Set Up

• IMPORTANT
  • The default Master Code is 12345678.  It is required that you change it to a code of your own before programming.

Notes

1. Beeps only sound when the Silent Mode is disabled.
2. If the indicators flash red light, it means your setting failed and it will require to re-enter master mode if you would like to continue your programming.

Factory Default Settings

How to Reset?

IMPORTANT : The resetting will delete  all user  codes stored  in the lock .

1. Step 1. Keep the door open and unlocked.
2. Step 2. Press and hold the Reset button, at the same time take out one battery and then place it back.
3. Step 3. Keep holding the Reset button for 3 seconds, until you hear the sound of “beep” and the latch will extend automatically.

Troubleshooting

Why does not the latch extend but the motor is/isn’t rotating when resetting my keypad lock?|
Improper installation may have caused the issue. Please follow the steps to review

1. 1. Please make sure the latch and strike are aligned. The deadbolt latch should be retracted(unlocked) through all your installation process.

2. Please recheck if the cable is attached completely in Step 4B.
3. Please make sure the thumb turn is vertical in your installation steps 4C and 5A.
4. Please open your door and reset the lock.

Why doesn’t the thumb tum rotate after installation completed?

• When the lock is learning wrong orientation of the door, the thumb turn won’t rotate.

Please reset your lock by following the steps

1. Keep the door opened and make sure the latch is retracted and thumb tum vertical.
2. Press and hold the reset button with one hand and the other hand lake out one battery and place it back.
3. Keep holding the Reset button for 3 seconds, until you hear the sound of rotating and the latch will extend automatically.

If resetting doesn’t solve the issue, you may need to re-install the whole lock.
Please make sure when you start to install, the lock is in unlocked status; Please make sure the thumb tum is vertical

• When I attempt to lock/unlock my deadbolt, why does the latch go in and out for a few times?
  • It happens when the latch and strike are misaligned.
  • Please make sure the bolt hole on the door frame is at least 1 inch deep, so that the bolt can be fully extended.
  • Please check if the door can be closed properly, the deadbolt should not impact the strike or door frame on the door frame side, it should go directly into the hole properly.
• Why does my keypad lock only work properly when the backup key is in? Why am I unable to pull the key out in the unlocked position?
  • You may need to re-install the whole lock.
  • Please make sure when you start to install, the lock is in unlocked status;
  • Please make sure the thumb tum is vertical.
  • Please do not put the backup key in the lock.
• What does 5 short and fast beeps mean while programming?
  • It alerts you either time-0ut or wrong entry.
  • Please be sure to complete each setting step within 5 seconds.
  • Please change the default master code in the first time programming.
• Please be sure the user code is with correct format and with 4 to 10 digits. What if I forget my Master Codes?
  • If you forget your Master code, resetting your lock, then the original master code (12345678) works, and all previous user codes will be erased.

Information & Safety Warnings

• Protect your User Codes and Master Code.
• Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
• Do not use an electric screwdriver during installation.
• This manufacturer advises that no lock can provide complete security by itself.
• This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and common sense
•  Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
•  The lock is water resistant. II can withstand water splashes; however, do not let water and liquids get into the lock.
•  Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>