Lavales B06T2 Wireless Transmitter and Receiver User Manual
- June 14, 2024
- Lavales
Table of Contents
Wireless
Transmitter and Receiver
User Manual
In the box
Product overview
| Button | Function | Operation |
|---|---|---|
| Power on | Press for about Is | |
| Enter pairing mode | Press for about 2s | |
| Power off | Press for about 4s | |
| TX | Transmitter mode | side to TX to enter transmitter mode: |
| RX | Receiver mode | slide to RX to enter receiver mode |
| Reset | Press for about 2s |
Tx mode
Rx mode
Instructions
TX Mode:
- Flip the mode button to “TX”. Press the button for 2s.When LED light flashes between red and blue the adapter will automatically enter into pair mode .
- Put your Bluetooth device such as Bluetooth headphones/earbuds/ speaker as close as possible with this adapter.
- Turn on your device’s Bluetooth and pair with BO6T2 Bluetooth adapter. They will pair automatically.
- Connect BO6T2 with your Phone / Tv / Tablet / PC / Laptop / MP3 / MP4 Projector through 3.5mm jack.
- Enjoy the music
RX Mode
- Flip the mode button to “Rx”. Press the button for 2s.When LED light flashes between red and blue the adapter will automatically enter into pair mode .
- Put your Bluetooth device such as TV/Tablet/PC/Laptop/Phone as close as possible with this adapter
- Turn on your device’s Bluetooth and pair with BO6T2 named adapter.
- Connect B06T2 with your speaker/headphone/ through 3.5mm jack.
- Enjoy the music.
How to enter pairing mode?
Press and hold the button for 2 seconds after powered on,BO6T2 will enter the
pairing mode (LED lights flashing red and blue).
How to pair the second device?
- Set BO6T2 to pairing mode again (press and hold the button for 2 seconds until the LED flashes red and blue).
- Activate the Bluetooth of the second mobile phone, find “BO6T2’, click connect, and wait for the pairing to succeed.
- Enjoy your music.
Note: You can only play music on one device at a time, so if you want to
play music on the second device, you need to pause the music on the first
device before playing it on the second device.
Charging method
-Plug in the charging cable to charge the BO6T2, and the LED will be steady
red.
-When the battery is fully charged, the LED indicator will turn off.
How to reset the device?
lf BO6T2 cannot be connected or does not work normally, please refer to the
following methods to reset the device:
Long press RESET button for 2 seconds, the white indicator light flashes 3
times at the same time, then it will enter pairing mode.
Control function
Note: In RX mode, if
there is a sound delay, please double-click button to improve the sound
quality.
CE
ANKBIT international. hereby declares that this product is in compliance with
the essential requirements and other relevant provisions of Directive
2014/53/EU.
In accordance with Article 10(2) and Article 10(10), this product is allowed
to be used in all EU member states.
Warranty
Warranty service is limited to normal use. Any man-made damages such as from
connecting to an unsuitable power source, using an unsuitable device, or not
following the instructions, as well as damages that did not occur during
shipping, repairs, and adjustments not approved by the company, darnages from
misuse, inattention, or improper installation may cause the warranty to be
ineffective immediately. This warranty does not include shipping fees.
Disposal
Always dispose of the used appliance at a recycling centre.
Do not dispose the used appliance together with household waste.
eVatmastes Consulting GmbH
Gettinastr. 30
60325 Frankfurt am Main,Germany
contact@evatmaster.com
Operator: Ankbit International Limited
Address: 45-51 Chatham Road South, Tsim Sha Tsui, Kowloon, Hong Kong
Manufacturer: Shenzhen Ankbit Electronics Limited
Address: Runfeng industrial Park, No. 4197 Baoan Blvd, xixiang St, Baoan
Dist, Shenzhen, China
FCC ID: 2AUFR-RTSOI3 IC: 29252-B03 HVIN: BOG
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>