ICANONIC Wireless Earbuds with Immersive Sounds True 5.0 Bluetooth in Ear Headphones User Manual
- June 14, 2024
- ICANONIC
Table of Contents
ICANONIC Wireless Earbuds with Immersive Sounds True 5.0 Bluetooth in Ear Headphones
PACKAGE CONTENTS
-
2 Wireless Earbuds
(Left/Right) -
Charging Case
-
Type-C Cable
-
Ear Caps (3 pairs)
-
User Manual
-
Warranty Card
HOW TO ACTIVATE EARBUDS (FIRST TIME USE)
-
Take out the Earbuds and pull the protective adhesive film off of the Earbuds.
-
Please put Earbuds back into the Charging Case and CLOSE it for at least 1 min. and then begin use_
PAIR
-
Open the Charging Case and take out the Earbuds to automatically Power them ON.
-
When the Charging Case is open, the White and Red lights will flash alternately. The voice prompt will say, “Pairing.
-
Go to Settings. Go to Bluetooth. Tap “ICANONIC”.
-
Earbuds are now connected.
What if you cannot find “ICANONIC” in your Bluetooth page?
Reason 1: Earbuds have paired to another device.
Solution: Disconnect the Earbuds by turning OFF the Bluetooth on the
mistaken connected devices, then pair the Earbuds to your preferred device.
Reason 2: The Earbuds has reached 0% battery life.
Solution: Place both Earbuds back into the Charging Case.
Allow the Earbuds to recharge for around 5 mins. If the Charging Case has run
out of battery, plug it into a USB power source with the Earbuds still inside.
(USB Cable provided).
Reason 3 : Earbuds are completely OFF.
Solution: You may have accidentally manually turned off the Earbuds.
Please press and hold the MFB buttons for 3-4
MODE
STEREO MODE
Open Charging Case and Earbuds will begin flashing White and Red and will then
automatically synch and pair.
SINGLE EAR MODE
Put one Earbud into Charging Case and CLOSE it. Your preferred Earbud will
enter Single Ear Mode when successfully paired to your phone.
HOW TO WEAR
STEP 1: Place the !CANONIC Earbud inside your ear.
STEP 2: Twist Earbud slightly forward for a snug fit.
NOTE: All ears are shaped and sized differently. Adjust accordingly.
EXAMPLES OF IMPROPER FIT
Do Not Rotate Earbuds Completely Vertical Or Horizontal (doing so WILL cause Earbuds to fall out).
HOW TO CHARGE EARBUDS AND CASE
-
Properly insert the Earbuds into the Charging Case.
-
CLOSE the Charging Case and plug in the Type-C Cable.
-
Now, the Earbuds and Charging Case are charging simultaneously.
IMPORTANT: If there is a GAP between the cable and case, it is NOT charging proper. Push cable FIRMLY into place and you will hear a loud CLICK sound knowing it’s charging properly. -
4-star LED Light Indicator will show battery percentage.
HOW TO USE THE MULTI-FUNCTION BUTTON
SINGLE PRESS
Music-Play/Pause
DOUBLE PRESS (LEFT/ RIGHT)
Music-Left for Playback. Right for Skip
SINGLE PRESS (LEFT/ RIGHT)
Calls-Answer/ End Calls or Switch Between Calls
SINGLE PRESS (LEFT/ RIGHT)
Calls-Press and Hold For 1 Second Will Reject Call
ACTIVATE VOICE ASSISTANT (SIRI, GOOGLE ASSISTANT)
Tap the MFB 3 times
FACTORY RESET
Follow the 2-Step Process to properly perform a Factory Reset.
IMPORTANT: You MUST turn OFF the earbuds first, before you RESET them. The Factory Reset is a 2-Step Process.
Step 1: TURN OFF (If Earbuds are already OFF, go to Step 2.)
ACTION: Hold MFB buttons for 3-4 seconds.
RESULT: (LED Lights will blink signaling the earbuds are OFF).
Step 2: RESET
ACTION: Hold MFB buttons for 10-15 seconds.
RESULT: (LED Lights will turn on, blink, then eventually stop).
COMPLETE
Earbuds are now RESET and enter OFF state.
IMPORTANT: After Factory Reset is performed, the device name will still
appear in the Bluetooth list. Tap “!CANONIC” and tap “Forget This Device”.
Then, you can try the pairing process again.
ATTENTION: Earbuds will be activated if removed from the Charging Case or if the Charging Case reaches 0% battery. They can be turned off manually by holding the MFB buttons for 3-4 seconds.
