BARSKA BC137 Laser Green Sight Instruction Manual

BARSKA BC137 Laser Green Sight

Product Information

• The BARSKA Green Laser Sight is constructed with high grade Aluminum.
• The laser sight is powder coated to avoid scratching or chipping.
• Ideal for target shooting in daylight or low light conditions.
• Can reach up to 1000m at night.
• Powered by one 3v (CR 123A) Lithium Battery.
• Visible Laser Class IIIA Laser Product.

Product Usage Instructions

Important Safety Precautions

• Keep out of reach of children.
• Do not point the laser at people, pets, shiny/highly reflective surfaces, or any other object not intended for designated use.

Attaching the Laser Sight to your Firearm

1. Slide the laser sight into the bore of the Picatinny rail.
2. Tighten it in place using an Allen wrench.
3. Slide the rail onto your firearm and tighten it in place with a flathead screwdriver

PRODUCT DIMENSIONS

• Diameter: 31mm
• Length: 28mm
• Width: 50mm
• Height: 60mm
• Model: BC137

DESCRIPTION

The BARSKA Green Laser Sight is easy to use and is constructed with high grade Aluminum. Laser sight has been powder coated, to avoid scratching or chipping. Ideal for target shooting in daylight or low light conditions, and reaches up to 1000m at night.
WARNING: BE CERTAIN THAT YOUR FIREARM IS NOT LOADED AND POINTED AWAY FROM YOU IN A SAFE DIRECTION
ATTENTION: THIS BARSKA LASER SIGHT IS A POWERFUL TARGETING DEVICE THAT REQUIRES SPECIAL ATTENTION WHEN OPERATING.
CAREFULLY READ THE FOLLOWING INSTRUCTIONS AND SAFETY PRECAUTIONS BEFORE USING THIS PRODUCT.
CAUTION: UNAUTHORIZED USE MODIFICATIONS OF ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN SPECIFIED HEREIN MAY RESULT IN DANGEROUS/HAZARDOUS RADIATION EXPOSURE.
LASER LIGHT: AVOID DIRECT EYE EXPOSURE.
WARNING KEEP OUT OF REACH OF CHILDREN.
DO NOT POINT LASER AT PEOPLE, PETS, SHINY/HIGHLY REFLECTIVE SURFACES, OR ANY OTHER OBJECT NOT INTENDED FOR DESIGNATED USE.

MOUNTING

Your laser sight is equipped with a Picatinny Rail. This rail will attach your laser to your firearm.

1. Slide the laser sight into the bore of the Picatinny rail.
2. Once the sight is in the rail tighten it in place by using an Allen wench.
3. Slide the rail onto your firearm, then tighten it in place with a flathead screw driver.

BATTERY INSTALLATION

This device is powered by one 3v (CR 123A) Lithium Battery.

1. Unscrew the cable switch by turning it counter clockwise
2. Insert the battery so that the positive pole of the battery faces out.
3. Replace the switch back on the laser sight. Turn clockwise to tighten the cable switch onto the sight. Make sure that you have screwed the switch on tightly.

WINDAGE & ELEVATION

Adjustments must be made in the shooter’s position of the sight. This laser sight has been factory calibrated. Should you require adjusting the windage and elevation remove turret caps and see chart below to distinguish which of these knobs you need to turn and in which direction.

CC: Counter Clockwise
C: Clockwise
ATTENTION
DO NOT attempt to adjust the screw on the outside of the laser (see image to the right).
Altering this screw may misalign your laser sight. This screw is for factory use only.

ACCESSORIES INCLUDED

• 1 Picatinny Mount
• 1 Cable Switch
• 3v (CR123A) battery

TECHNICAL DATA

• Length                              138 mm
• Weight                              210g
• Tube Diameter              31mm
• Dot Size                          <15mm at 10m
• Output Power                <5mW
• Wavelength                      532+10nm
• Reach                                1000m at night
• Adjustment                      Windage & Elevation
• Housing Material            Aluminum Waterproof
• Battery Type                    CR123A lithium

2008 BARSKA® La Verne, CA 91750, USA
www.barska.com

References

• Barska - Your Ultimate Source for Premium Safes and Outdoor Gear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>