Eleglide S1 PLUS Electric Scooter User Manual

Eleglide S1 PLUS Electric Scooter

Note

This manual was written to help you get the most performance, comfort, enjoyment and safety when riding your new Eleglide electric scooter(hereinafter referred to as e-scooter). It is important for you to understand your new e-scooter. By reading this manual before you go out on your first ride, you’ll know how to get the most from your new e-scooter. It is also important that your first ride on your new e-scooter is taken in a controlled environment, away from cars, obstacles, and other riders.

The e-scooter a recreational product. Before mastering riding skills, you need to practice. Neither Eleglide Team nor its Resellers are responsible for any injuries or damage caused by a rider’s inexperience or failure to follow the instructions in this document.
E-scooter are vehicles with certain risks, please make sure to follow the traffic rules. Also, when emergency braking, apply brakes to the rear wheel first, and only then the front wheel, especially if the cycling speed is too high. If the front brake is used suddenly, you may fall over. Please ride carefully.

The e-scooter is supplied without basic mandatory equipment, which may vary from place to place. Therefore, if you intend using the e-scooter on public roads, it’s necessary to equip the bike with the basic mandatory equipment, in accordance with the relevant laws and regulations.

This product is designed for home use. Do not use it for commercial or other purposes.
Keep this manual in a safe place to be able to find information in the future or for other users.

Packing List

When unpacking your e-scooter, please verify that the above items are included in the package. If you are missing any components, please contact your dealer/distributor or nearest service center (see Contact in the user manual). After verifying that all components are present and in good condition, you can assemble your new e-scooter.

Please retain the box and packaging materials in case you need to ship your e-scooter in the future. Remember to power off your e-scooter and unplug the power cord before assembling, mounting accessories, or cleaning the mainframe.

Diagram

Function Instruction：
On/off : Press on/off button for 3 second, the e-scooter will be of / on.
Mode button: press it could help you to change the speed mode(supports up to 3-level speed) Accelerator: Use it to speed up.
Cruise function: Twist and hold the accelerator for up to 5 second to activate the cruise control  function.
LED Light On/Off: Press the button.

Assembling Your E-scooter

1. Get it out and unfold it: Unfold the handlebar stem and fasten. Then unfold the kickstand to support the e-scooter.
2. Check the handlebar: Lift up the handlebar and check if it’s fasten. If handlebar is loose, Fold the handlebar and fasted the screw with the included hex wrenches.
3. Display Assembling: Put it on the right handlebar and fasten it in the right position with the tool in the package.
4. Battery supply: Use the key to get the battery supply. (Please take care of the key)
5. Finished: The bike is ready for your first ride. Turn on the battery and the bike, go out with it.

First Ride

Warning: Wear an approved helmet and other protective gear to minimize any possible injury. And if you intend using the e-scooter on public roads, it’s necessary to equip the bike with the basic mandatory equipment, in accordance with the relevant laws and regulations.

• A. Power on (Press On/off button for 3 seconds) the E-scooter and check the power level indicator. Charge the E-scooter if the battery level is low.

• B. Stand on the footrest with one foot and push off with another foot to start gliding.

• C. Put your other foot on the footrest to keep both feet stable. Press the throttle on the right hand to speed up when you are balanced.
  Note, for your safety, the motor will not engage until the e-scooter reaches 1.86 mph (3 km/h).

• D. Slow down by releasing the throttle; and brake by squeezing the brake lever.

• E. To turn, shift your body weight and turn the handle slightly.

Folding and Carrying

1. Handlebar Folding: Horizontal slide outward the lock sleeve and put down the handlebar.
2. Put down the telescopic rod: Loose the quick release clip and put the telescopic rod down to a right position.
3. Scooter Folding: Hold the scooter upright rod and pull down the folding handle. Make the kickstand be folded as well.
4. Carrying: Hold the rod and take it to where you want.

Trouble Shooting

LED Display Error Code

Code| Possible Causes| Solutions
ERRO 1| Motor Problem|

• Check and Plug the wire in properly.
• Revise/Replace the Motor

ERRO 2| Accelerator|

• Revise/Replace LED Dispaly

ERRO 3| Controller Problem|

• Revise/Replace controller

ERRO 4| Brake Lever Problem|

• Replace the Brake Lever wire.
• Replace the brake lever
• Contact re-seller.

ERRO 5| Low-voltage protection|

• Charge it.
• Contact re-seller.

ERRO 6| Communication failure, Led display can not receive the instruction from controller|

• Check and Plug the wire in properly.
• Replace the motor
• .Replace the LED display
• Contact re-seller.

ERRO 7| Communication failure, controller can not receive the instruction from Led display|

• Check and Plug the wire in properly.
• Replace the motor
• Replace the LED display
• Contact re-seller.

Other Problem

Problem| Possible Causes| Solutions
Display and power indicator does not work|

• No power supply for vehicles.
• The electric wire is not plugged in properly
• Display is damaged
• Controller burnout or water damage

|

• Charge the battery
• Reconnect the electric wire properly C &
• Contact the re-seller for helping to solve it.

Battery does not charge|

• Charger is not plugged in properly
• Battery if out/below of temperature site.
• Battery is under rated voltage

|

• Plug the wire in properly.
• Contact reseller.

Insufficient Range|

• Battery is not in full charge.
• Tyre pressure is low
• Frequent braking
• Battery aging or attenuation
• Low ambient temperature, battery

|

• Plug in properly and charge.
• Make sure it is the resume Charging temperature.
• Contact re-seller.

Motor does not work|

• The electric wire is not plugged in properly
• Sensor / controller is inefficient

|

• Charge the battery fully.
• Check the pressure before every use.
• Develop good drive habits.
• It’s normal.
• Contact re-seller.

Attention: If any other failures occurred and you can not find any solution above, please contact the re-seller to solve it. And if you need to which need professional tools, in order to avoid danger, the machine must be repaired or replaced by manufacturer, other maintenance offices or professionals from similar offices.

Maintenance

Cleaning and Storage
Use a soft, wet cloth to wipe the mainframe clean. Dirt hard to remove can be scrubbed with a toothbrush and toothpaste, then cleaned with a soft, wet cloth.

NOTE
Do not wash your e-scooter with alcohol, gasoline, acetone, or other corrosive/volatile solvents. These substances
may damage the appearance and internal structure of your e-scooter. Do not wash your e-scooter with a power washer or hose.

WARNING
Make sure the e-scooter is powered OFF, the power cord is unplugged, and the rubber cap on the charge port is tightly sealed before cleaning; otherwise you may damage the electronic components. Store your e-scooter in a cool, dry place. Do not store it outdoors for extended periods of time. Exposure to sunlight and temperature extremes (both hot and cold) will accelerate the aging process of the plastic components and may reduce battery life.

Tire Pressure
Inflate tires to 36 psi. Inflate both tires equally.

Battery Pack Maintenance
Do not store or charge the battery at temperatures outside the stated limits (see Specifications). Do not puncture the battery. Refer to your local laws and regulations regarding battery recycling and/or disposal.
A well maintained battery can perform well even after many miles of riding. Charge the battery after each ride and avoid draining the battery completely. When used at room temperature 25℃ the battery range and performance is at its best; whereas using it at temperatures below 0°C can decrease range and performance. Typically, at -5℃ range can be half that of the same battery at 25°C. Battery range will recover when temperature rises.

NOTE
Typically, a fully charged battery should retain power for 60-120days. A low- power battery should retain power for 30–60 days. Remember to charge the battery after each use. Completely draining the battery may cause permanent damage to the battery. Electronics inside the battery record the charge- discharge condition of the battery; damage caused by over-charging or under- charging will not be covered by the Limited Warranty.

WARNING
Do not attempt to disassemble the battery. Do not touch battery contacts. Do not dismantle or puncture the casing. Keep the battery contacts away from metal objects to prevent short circuit. Risk of fire and electric shock. No user serviceable parts. Do not charge or use your battery if it is damaged or see trace of water.

WARNING
Do not ride when the ambient temperature is outside the machine operation temperature (see Specifications) because low/high temperature will limit the maximum power/torque. Doing so could cause personal injury or property damage due to slips or falls.

Specification

Speed

| Speed 1| 9KM/H| 9KM/H
Speed 2| 18KM/H| 18KM/H
Speed 3| 24KM/H| 24KM/H
Brake| Disk brake and E-brake
Slope| 12°| 12°
Max Mileage| Up to 30KM| Up to 45KM
Brake Distance| 6M| 6M
Max Speed| 24KM/H| 24KM/H

Battery

| Voltage| 36V| 36V
Capacity| 8AH| 12.5AH
Charging time| 3-4H| 6-7H
Motor| Rated Voltage| 36V| 36V
Rated Power| 400W| 400W

NOTE
Above max speed and mileage data are provided by the Eleglide lab. The e-scooter was fully charged under regular environment temperature around 25℃, no wind and with a 70kg load on the e-scooter. Driven on a flat road with an average speed of 20km/h.
The actual data may vary based on different road conditions, temperature, humidity, wind speed, and rider’s habit (whether often use the brakes, frequently shift speeds, etc.) and rider’s weight.

Warranty

This product enjoys one year warranty for the machine and 6 months warranty for the battery service starting from the date of purchase.

Excluded from the guarantee is normal wear, commercial use, alterations to the appliance as purchased, cleaning activities, consequences of improper use or damage by the purchaser or a third person, damage, that can be attributed to external circumstances or caused by the batteries.

• Inappropriate product selection and the fact that the product does not meet your requirement can not be a reason for complaint. Buyers is familiar with the properties of the product.
• Buyer has the right to ask the sellers to check the functionality of the product and become familiar with its operation.
• prerequisite for receiving warranty claims is that the guidelines for operating, servicing, cleaning, storage and maintenance were followed.
• Damage caused by natural wear and tear, overloading, improper use or intervention outside the authorized service during the warranty period, are excluded from the guarantee.
• Warranty does not cover wear and tear of components known as common consumables (e.g., Bearings, carbon brushes, commutators, chains, tires, wheel tubes.
• From the warranty are excluded wear and tear of the product or parts caused by normal use of the product or parts of the product (e.g., low battery or reduce battery capacity after a period of usual life of 6 months) and other parts subject to natural wear and tear.
• Damage resulting from defects in material or manufacturer error will be eliminated free of charge by replacement delivery or repair.
• Maintenance, inspection and alignment tools are not the warranty act.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>