AMP Motorization AMP28B DC Tubular Motor with Built In Rechargeable Battery User Guide

AMP Motorization AMP28B DC Tubular Motor with Built In Rechargeable

Battery

Product Information

This device is a motorized roller blind system that can be controlled using a remote control. The system is designed to comply with U.S. Radio Frequency FCC rules and regulations, ensuring that it operates without causing harmful interference and accepts any interference received.

The device is also compliant with FCC radiation exposure limits for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator (motor) and the user’s body to ensure safe usage.

The device can be paired with a remote control for easy operation. It has multiple features and settings, including switch rotating direction, setting upper and lower limits, adding or removing favorite positions, roller mode and sheer mode switch, adjusting limits, pairing or unpairing additional emitters, and speed regulation.

Product Usage Instructions

1. Pairing: Press and hold the P1 button for 2 seconds, then press and hold the Stop button for 2 seconds.
2. Switch Rotating Direction: Press and hold the Up and Down buttons together for 2 seconds.
3. Setting Upper & Lower Limits: To set the upper limit, press and hold the Up button for 2 seconds, then press and hold the Up and Stop buttons together for 2 seconds. To set the lower limit, press and hold the Down button for 2 seconds, then press and hold the Down and Stop buttons together for 2 seconds.
4. Add / Remove Favorite Position: Press the P2 button, then press the Stop button twice.
5. Roller Mode & Sheer Mode Switch: Press and hold the Up and Down buttons together for 5 seconds, then press the Stop button.
6. Adjust Limits: To adjust the upper limit, press and hold the Up and Stop buttons together for 5 seconds, then use the Up or Down buttons to adjust. Press and hold the Up and Stop buttons again for 2 seconds to confirm. To adjust the lower limit, press and hold the Down and Stop buttons together for 5 seconds, then use the Up or Down buttons to adjust. Press and hold the Down and Stop buttons again for 2 seconds to confirm.
7. Pair / Unpair Additional Emitter: Press the P2 button (existing), then press the P2 button (existing) again, and finally press the P2 button (new).
8. Speed Regulation: To increase speed, press the P2 button, then press the Up button twice. To decrease speed, press the P2 button, then press the Down button twice.

Troubleshooting

Issue: Built-in battery is depleted or insufficient charging from Solar PV Panel

Possible Causes: Recharge with compatible AC adaptor and check connection and positioning of solar PV panel. Check connection and orientation of solar PV panel.

Issue: Remote control battery is discharged or battery is inserted incorrectly into remote control

Possible Causes: Replace battery. Check battery polarity.

Issue: The motor is not responding

Possible Causes: Radio interference/shielding. Ensure remote control and the antenna on the motor are positioned away from metal objects. Receiver is far away from Remote Control Power failure. Incorrect wiring.

Issue: Motor beeps 10 times when in use or battery voltage is low / PV (solar panel issue)

Possible Causes: Recharge with AC adapter or check connection and positioning of solar PV panel.

Issue: Cannot program a single motor (multiple motors respond)

Possible Causes: Multiple motors are paired to the same channel. Move remote control to a closer position. Check power supply to motor is connected and active. Check that wiring is connected correctly (refer to motor installation instructions).
Always reserve an individual channel for programming functions.
SYSTEM BEST PRACTICE – Provide an extra 15 channel remote in your multi-motor projects that provides individual control for each motor for programming purposes. Place all other motors into sleep mode (refer to 1 button instructions).

Fields of Application

Specifications

• Working temperature: – 10° C ~ +50° C
• Input Voltage: USB 5V 1A / USB 5V 2A
• Radio Frequency: 433.925 MHz
• Maximum Running Time: 6 minutes

The motor is suitable for motorization of roller shades, sheer shades, roman shades, and revolve shades.

Attention
Never drop, knock, drill or submerge the motor. Keep the power cable in the proper position as shown below.
Read all safety instructions before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Safety Instructions

1. Do not expose motor to humid, damp, or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure the power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls should be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11.  Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty.

Charging Instructions

This motor has a built in Li-ion battery pack with integrated charge management.

• Max power input for recharging: 5V 2A.
• Before first use please charge motor for 6 hours using a 5V charger.
• During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and needs to be charged.
• During operation, if the voltage is detected to be too low, the battery stops running and needs to be recharged.

Rechargeable Battery

P1 Button Instructions

1. Test Motor
   Happening as you press for 1 second

2. Activate Pairing Mode
   Happening as you press for 2 seconds

3. Sleep Mode
   Happening as you press for 6 seconds

4. Reverse Direction
   Happening as you press for 10 seconds

5. Reset To Factory Settings
   Happening as you press for 14 seconds

Button Instructions

Essential Settings
The steps in factory mode must be completed to ensure proper operation.

Pair / Unpair Remote Control

• a. Press “p1” button (about 2 sec) on the motor head until motor jog x1 and beep x1.
• b. In the next 10 secs, press and hold “Stop” button on the remote control until motor jog x2 and beep x3.

Repeat the same procedure to unpair remote control.

Change Motor Direction (if necessary)

Press “Up” or “Down” button to check if the shade moves in the desired direction.
If you need to reverse the direction, press and hold (about 2 sec) “Up” and “Down” buttons simultaneously until motor jog x1 and beep x1.

The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing P1 button (See P1 button instructions).

Setting the Upper and Lower Limits

Set Upper Limit

• a. Press “Up” button to raise the shade, then press “Stop” button when it is in the desired upper limit.
• b. Press and hold (about 2 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

Set Lower Limit

• a. Press “Down” button to lower the shade, then press “Stop” button when it is in the desired lower limit.
• b. Press and hold (about 2 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

If you exit the limit setting status before you finish the limit settings, the motor will  take the previous existing limits.

Adjust Limits

Adjust the Upper Limit

• a. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
• b. Use “Up” button to raise the shade to the desired highest position, and use “Up” or “Down” button to do the final adjustment if necessary.
• c. Press and hold (about 2 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

Adjust the Lower Limit

• a. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
• b. Use “Down” button to lower the shade to the desired lowest position, and use “Up” or “Down” button to do the final adjustment if necessary.
• С. Press and hold (about 2 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

Favorite Position

Set Favorite Position

• a. Use “Up” or “Down” button to move the shade to desired Favorite position.
• b. Press one “P2” button on the back of remote control until motor jog x1 and beep x1.
• c. Press and hold (about 2 sec) “Stop” button until motor jog x1 and beep x1.
• d. Once more, press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.

Send Shade to Favorite Position
Press and hold (about 2 sec) “Stop” button, motor will move to Favorite position.

Delete Favorite Position

• a. Press one “P2” button until motor jog and beep x1.
• b. Press and hold (about 2 sec) “Stop” button until motor jog and beep x1.
• c. Once more, press and hold (about 2 sec) “Stop” button until motor jog x1 and long beep x1.

Roller Mode and Sheer Mode

Roller Shade Mode – continue movement after a short press – Default Mode

• a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1
• b. Press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.

Sheer Shade Mode – jog movement after a short press (continue movement after a long press)

• a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1.
• b. Press and hold (about 2 sec) “Stop” button until motor jog x1 and beep x1.

Add or Remove Additional Remote

Using Current Remote Control

• a. On the current remote control, press one “P2” button until motor jog x1 and beep x1.
• b. Once more, on the current remote control, press one “P2” button until motor jog x1 and beep x1.
• c. On the New remote control, press one “P2” button until motor jog x2 and beep x3.
  Repeat the same procedure to remove additional remote control.

New Remote Control

• Follow instructions under the section 1.
• Pair / Unpair Remote Control

Adjust Motor Speed

Acceleration Speed

• a. Press one “P2” button until motor jog x1 and beep x1.
• b. Press “Up” button until motor jog x1 and beep x1.
• c. Once more, press “Up” button until motor jog x2 and beep x1.

Deceleration Speed

• a. Press one “P2” button until motor jog x1 and beep x1.
• b. Press “Down” button until motor jog x1 and beep x1.
• c. Once more, press “Down” button until motor jog x2 and beep x1.
  If the motor has no response, it already has a Maximum or Minimum speed.

Declarations
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. onnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
   Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
   FCC RF Radiation Exposure Statement:
   This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAN ICES-003 (B)/NMB-003(B)

Quick Index

Troubleshooting

Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.

Please scan QR code to see more AMP’™* product information

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>