RETROFLAG 74BA-2.4G Classic Wireless 2.4g Gaming Controller User Manual
- June 15, 2024
- RETROFLAG
Table of Contents
RETROFLAG 74BA-2.4G Classic Wireless 2.4g Gaming Controller
Classic 2.46 Controller-M
Switch / Windows / MD mini / MD mini 2
- Connect the 2.4g receiver to your device.
- Press Start to turn on the controller.
- Wait until your device recognizes the controller to play.
Buttons| A| B| C| X| Y| Z| | R|
SELECT| START
---|---|---|---|---|---|---|---|---|---|---
Switch| A| B| R| X| Y| | ZL| ZR| –| +
Windows| A| B| RT| X| Y| RB| LB| LT| View| Menu
MD mini / mini 2| A| B| C| X| Y| Z| Z| C| Mode| Start
*Switch/ Windows: Press & hold SELECT +START= HOME
Remap D-pad
Left+ Select: set D-pad as left analogue stick.
Right + Select: set D-pad as right analogue stick.
Up+ Select: reset D-pad.
- Available for Windows only.
- Press and hold any of the button combinations above for 5 seconds to remap the D-pad.
- LED will blink in blue to indicate the success of D-pad remapping.
- You need to reset the D-pad manually.
Turbo
- Hold L+SELECT first, then press the button you would like to set turbo functionality to.
- Auto-Turbo: Hold L+SELECT first, then double press the A/B/C/X/Y /Z button;
- Pause/Restart Auto-Turbo function via press the button you set.
- Supported buttons: A, B, C, X, Y, Z
- The turbo function will not be saved after you restart the controller.
Button Swapping
Hold any of two buttons you would like to swap, then press and hold L+R+SELECT to complete the button swapping.
- Supported buttons: A, B, C, X, Y, Z
- The button swapping function will not be saved after you restart the controller.
Battery & Status LED
Battery capacity: 480mAh
Charging time: Approx. 1 ~2 hours
Battery life: Approx. 40 hours
Power Status LED
- Red LED flashing — Low battery
- Red LED solid – Charging
- Red LED light out – Fully charged
Controller/Receiver working status LED
- Blue LED slowly flashing – Reconnecting
- Blue LED rapidly flashing ·- Pairing
- Blue LED solid – Connected
Pair with the 2.4g receiver
If the controller loses the connection with the receiver, please shorten the distance between them, hold the SELECT button of the controller for 5 seconds after turn on the controller till the Blue status LED rapidly flashing to reconnect.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>