Pinetree G6 Bone Conduction Headphone User Manual

Pinetree G6 Bone Conduction Headphone

LIST OF ITEMS

1. Earphone x 1

2. Charging cable x 1

3. User manual x 1

PRODUCT SPECIFICATION

Product material : ABS+PC
BT version : V5.3
Working frequency band : ISM band (2.402-2.480GHZ)
Battery capacity : 140mAh
Rated input : 5V=120mA
Playing time : about 2hours
Product material : about 8hours(70%VOL)
(All technical information is subject to actual performance)

PRODUCT INTRODUCTION

1. Except for the operation methods specifically marked in the manual please do not try to disassemble or replace any parts in the headphone.
2. If any liquid accidentally enters the product, disconnect and separate the product immediately.
3. To avoid electronic shock, please make sure that there is no water on your hands when installing or uninstalling the headphone.
4. Do not place the headphone near a heat source or directly expose them to a fire source.
5. Do not place the headphone in an environment with strong electromagnetic force, otherwise they will malfunction.

PRODUCT OPERATION INSTRUCTIONS

1. POWER ON/OFF
   POWER ON: Press thV+ key 3s, red and blue lights flash alternately
   POWER OFF: Press the V+ key 5s,The red light flash
   

2. BT connection
   After the headset is turned on, turn on the smart device, find the smart device settings, turn on BT(as shown) BT search shows G6 click Red light and blue light-off after the connection is successful

Pairing status Light prompt: Red light and blue light Alternate flashing Pairing successful Light alert: Red light and blue light-off

PRODUCT DIAGRAM

1. Call microphone
2. Indicator light
3. Noise reduction microphone
4. “+” key
5. “_” key

INDICATOR LIGHT DESCRIPTION

Alternating flashing of red and blue

|

pairing status

---|---

Red light and blue light-off

| connected successfully
Red light always-on|

Charging

Blue light always-on

|

fully charged

PRODUCT OPERATION INSTRUCTIONS

After the normal connection, the phone will show the power of the headset, if the power shows red, it means charging is needed Plug the 5V charger into the USB charging cable to charge.

FUNCTION OPERATION

NAME AND CONTENT OF HAZARDOUS SUBSTANCES IN PRODUCTS

Name and content of hazardous substances in products

This form is compiled in accordance with SJ/T 11364.
o: Indicates that the content of the hazardous substance in all homogeneous materials of the part is in Below the limit requirements specified in GB/T 26572.
X Indicates that the content of the hazardous substance in at least one of the homogeneous materials of the part exceeds the limit requirements specified in GB/T 26572.
The parts marked with “x” on the form cannot be replaced by hazardous substances due to restrictions on the global technological development level.
Printed circuit board components* : including printed circuit boards and their parts, electronic components, etc., Depending on the product model, the product you purchase   may not contain all the above components
| Electronic and electrical products sold in the People’s Republic of China must mark this Logo, the number in the logo represents the product under normal use environmental protection use period.

FCC WARNING MESSAGES

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>